Table of Contents
Advertisement
or
. When either input
AUDIO
VIDEO
type is highlighted in reverse video use
the
or
buttons
to select the
i
‹
›
source you wish to listen to or view.
Remember that the video source should
be selected first when you wish to watch
one source and listen to another.
To select a digital audio input use the
or
buttons
to position the on-
i
⁄
¤
screen cursor
next to
>
DIGITAL
and note that the word
Select j
will be highlighted in reverse
DIGITAL
video. Then use the
or
‹
›
to select the desired digital source. Note
that when any digital source is selected,
the audio source will indicate
You may also use this menu to turn the
attenuation, or ATT, function on or off
for a source by moving the cursor to the
line and using the
or
‹
ATT
to select
or
. When the ATT
i
ON
OFF
function is enabled the input level is
reduced to prevent overloading the input
circuits.
: At this menu (see
SURROUND MODE
figure #15) you may change the
surround mode by using the
buttons
i
to position the on-screen
cursor
next to
and using the
>
MODE
or
buttons
to select the desired
i
‹
›
mode. To change the delay time position
the cursor next to
SURROUND CH
then use the
or
buttons
‹
›
desired delay time for the surround
channels. Note that an adjustment for
the delay time of the center channel is
possible only in the Dolby Digital mode.
: At this menu you
TEST TONE
may adjust the front and surround
speaker output levels. For information
on this procedure, refer to the System
Configuration section of this manual.
On-Screen Display
SET UP MENU
using the Setup menus, refer to the
System Configuration section of this
manual.
SLEEP TIMER SET
to set the sleep timer, which will place the
unit in a standby mode after a set period
of time. To reach this menu, press the
or
buttons
¤
. Press
screen cursor
and press
the
SLEEP TIMER SET
buttons
gure #16) the cursor will be next to
i
TIMER SET
to select the amount of time before
i
.
turn off and note that the time will blink.
**
Press the
cursor
>
is next to
or
buttons
‹
›
buttons
press
Select j
›
stop flashing indicating that the timer
has been started. Press
so that the cursor is next to
TO MAIN MENU
Note that when the
to the screen the time figure
will appear next to the words
or
. You may check the time
⁄
¤
TIMER
remaining before shut off at any time
by pressing the
the remote and viewing the front panel
or on-screen display (see figure #12).
and
to select
Position the on-screen cursor
i
to
MENU OFF
menu system and return to normal
operation.
27
: For information on
: This enables you
to position the on-
i
next to
>
SLEEP TIMER
. At the next screen,
Select j
menu (see fi
. Use the
or
buttons
‹
›
button so that the on-screen
¤
. Use the
TIMER OFF ON
to highlight
i
ON
. The time figure will
one more time
¤
RETURN
and press
Select j
returns
MAIN MENU
SLEEP
button
z
on
Sleep
next
>
at any time to exit the
S U R R O U N D
M O D E
: P R O
D E L A Y
T I M E
C E N T E R
C H
S U R R O U N D
R E T U R N
T O
⁄
Figure 15
S L E E P
T I M E R
T I M E R
S E T
T I M E R
O F F
R E T U R N
T O
Figure 16
and
.
M O D E
L O G I C
C O N T R O L
: N O N E
C H
: 2 m s
M A I N
M E N U
S E T
1 0 m i n
O N
M A I N
M E N U
Hide quick links:
Advertisement
Table of Contents
