Table of Contents
Advertisement
System Setup
Once the speakers have been placed in
the room and connected, the final step
is to enter the configuration information
and balance the speaker output levels.
Before proceeding further this is a good
time to review the installation section
of the manual to make certain that all
connections are properly made.
1. Plug the unit into an AC wall outlet
and press the
button on the
Power
front panel
. Note that the ring sur-
1
rounding the front panel switch will
turn red, then green, and the front panel
display will illuminate.
2. Install the supplied AAA batteries in
the remote as shown on page 15.
3. Turn on the TV connected to the
receiver. Select the appropriate video
input on the TV.
NOTE: Although the unit will switch
S-Video signals, the on-screen menus
control system is NOT visible on the
S-Video output.
4. Press the
button
j
Select
remote to bring the
MAIN MENU
your video screen.
5. Press the
button four times until
¤
the on-screen cursor
is pointing to
>
(see figure #1).
SET UP MENU
6. Press
to move to the
Select j
next screen,
SET UP MENU 1
figure #2).
System Configuration
7.
SET UP MENU 1
information that tells the AVR75 which
type of front and surround speakers
will be used. In turn, these settings will
determine which speakers receive low
frequency (bass) information. For the
purposes of establishing proper bass
reproduction, use the
the speaker being used at any position
is a traditional full-range loudspeaker
that is capable of reproducing sounds
below 100Hz. Use the
smaller, frequency-limited satellite
speakers that are not able to reproduce
sounds below 100Hz. Note that when
"small" speakers are used it is advisable
to install a separate subwoofer.
8. Enter the information for the
. speaker by using the
CH
on the remote to select the type of
i
front channel speaker that will be used.
Press the buttons so that
is highlighted to match the
SMALL
speaker type you will use as described in
item #7 above. The
a full-range output to the front left/right
speakers, while the
on the
low-frequency sounds to the subwoofer
up on
output. When the selection has been
made, press the
the on-screen cursor
to the
SURROUND CH
display.
(see
18
enters the
settings if
LARGE
setting for
SMALL
FRONT
or
buttons
‹
›
or
LARGE
setting sends
LARGE
setting sends
SMALL
button once so that
¤
is pointing
>
. line of the
M A I N
M E N U
I N P U T
S E L E C T O R
S U R R O U N D
M O D E
T E S T
T O N E
M U L T I
R O O M
S E L : O F F
S E T
U P
M E N U
S L E E P
T I M E R : O F F
M E N U
O F F
Figure 1
S E T U P
M E N U
S P E A K E R
S E T T I N G
F R O N T
C H .
S U R R O U N D
C H .
G O
T O
S E T
U P
R E T U R N
T O
M A I N
Figure 2
S E T U P
M E N U
C E N T E R
C H .
S U B W O O F E R
G O
T O
S E T
U P
R E T U R N
T O
M A I N
Figure 3
S E T U P
M E N U
L F E
L E V E L
C O N T R O L
O F F : 0 d B
N I G H T
M O D E
: O F F
S E T U P
L O C K
: L O C K
R E T U R N
T O
M A I N
Figure 4
T E S T
T O N E
O F F
O N
F R O N T
L
0
d B
Figure 5
1
L A R G E
S M A L L
L A R G E
S M A L L
N O N E
M E N U
2
M E N U
2
L A R G E
S M A L L
N O N E
O N
O F F
M E N U
3
M E N U
3
-
1 0 d B
O N
U N L O C K
M E N U
Hide quick links:
Advertisement
Table of Contents
