Table of Contents
Advertisement
9. Enter the information for the
. speaker by using the
SURROUND CH
or
buttons
on the remote to
i
‹
›
select the type of surround channel
speaker that will be used. Press the
buttons so that
,
LARGE
SMALL
is highlighted to match the speak-
NONE
er type you will use as described
in #7 above. The
setting sends a
LARGE
full range output to the left/right
surround speakers, while the
setting sends low-frequency sounds to
the subwoofer output or to the front
speakers when no subwoofer is selected.
If the surround speakers will not be used,
the
setting will send the audio for
NONE
the surround channels to the front
left/right speakers. When the selection
has been made, press the
¤
so that the on-screen cursor
ing to
GO TO SETUP MENU 2
to move to the next menu.
Select j
10. At
(see figure #3),
SETUP MENU 2
you enter information that configures
the AVR75 for the type of center channel
speaker to be used, and whether or not a
subwoofer is in use. While the on-screen
cursor is pointing to
CENTER CH
the
or
buttons
on the remote to
i
‹
›
select the correct type of center channel
speaker as described in #7. When
is highlighted a full-range sig-
LARGE
nal will be sent to the center channel.
When
is highlighted the audio
SMALL
to the center channel will be cut at
100Hz and low-frequency information
will be routed to the subwoofer output or
to the front left/right speakers if no sub-
woofer is selected. When the selection has
been made, press the
button once so
¤
that the on-screen cursor
>
the
line of the display.
SUBWOOFER
11. At the
line use
SUBWOOFER
the
or
buttons
on the remote
i
‹
›
System Configuration
to highlight
an optional external subwoofer is con-
nected to the
Output ⁄
highlight
or
frequency sounds (below 100Hz) will be
routed to the front left/right speakers.
Note that the subwoofer cannot be set to
when the front speakers are set to
O F F
in
SMALL
selection has been made press the
SMALL
button once so that the on-screen cursor
is pointing to
>
. Press
Select j
3
menu.
12. At
SETUP MENU 3
various control functions will be set.
The first item is the
button once
CONTROL
is point-
>
Effects channel that is used when Dolby
. Press
Digital signals are present. The normal
setting for LFE is 0dB, but the control
may also be set to -10dB
for reduced output when an LFE signal
is present. The LFE may also be turned
to reduce low-frequency repro-
OFF
duction. When the LFE level is set, or
. press
to bypass this setting, press the
button
i
the next setting.
NOTE: When the LFE is set to
LFE output is cut, and not sent to any
other speaker.
13. The next line is the
setting. This feature reduces the input
is pointing to
19
or
. Select
when
ON
OFF
ON
Subwoofer Preamp
. If a subwoofer is not used,
. In this position all low-
OFF
. When the
SETUP MENU 1
¤
GO TO SETUP MENU
to move to the next
(see figure #4),
LFE LEVEL
. "LFE" is the Low-Frequency
¤
on the remote to move to
the
OFF
NIGHT MODE
level for Dolby Digital sources only by
/
to
/
at their loudest thresholds,
1
3
1
4
preventing unwanted bursts of loud
sounds without restricting the dynamic
range or volume of other sounds or at
less than maximum levels. The feature
may be turned
by pressing the
OFF
or
buttons
on the remote until
i
‹
›
is highlighted. The Night mode
OFF
may also be turned on and off at any
time by pressing the
Night
on the remote. When the Night mode is
set, or to bypass this setting, press the
button
to move to the next setting.
i
14. The
prevents any of
SETUP LOCK
the major control settings from being
changed once it is engaged. This feature
is set at the factory to
UNLOCK
all settings may be adjusted. If you wish
to prevent settings from being easily or
inadvertently being changed, use the
or
buttons
on the remote until
i
‹
›
is highlighted. Once the
LOCK
setting is engaged and you exit
, no changes may be made to
MENU 3
any of the Setup menus. To make
changes to these menus you must return
to
and use the
SETUP MENU 3
buttons
on the remote until
i
is highlighted. When the
UNLOCK
setting is engaged, the word
LOCK
will appear at the top of the
LOCK
menus to remind you that no changes
may be made. When all adjustments
have been made, press the
¤
twice and then press
Select j
RETURN TO THE MAIN MENU
At this point you may wish to adjust
the delay time settings, although it is
button
e
¤
, so that
LOCK
SETUP
or
‹
›
button
i
to
.
Hide quick links:
Advertisement
Table of Contents
