Table of Contents
Advertisement
To some ears the impact of the wrap cir-
cuit may seem subtle, and this is normal.
Remember that how audible the wrap
effect will be varies with the acoustics of
your listening room, the output settings
established during the calibration process,
the system volume and the type of pro-
gram material in use.
Ref
Wrap
A) When the Wrap indicator appears in
the "Reference" position, the special Wrap
circuits are not being used and the unit is
in the pure Pro Logic mode.
Ref
Wrap
B) This display appears when the
maximum Wrap is applied.
Ref
Wrap
C) This display appears in the "Phantom"
mode or when a center channel speaker
is not installed.
Operation
17
Note that the Wrap circuit is not in use
when the
Wrap Indicator ˜
the two lights connected by the REF
bar along with the center, front and
middle LED.
When the
buttons
ˆo
Wrap
pressed when the AVR40 is in the
mode, the circuits are adjusting a con-
trolled amount of level into the rear
channels. The amount of this change
will be indicated in the
Information
. Note that the range of control
Display
for the Wrap circuit in the
will vary depending on other system
settings, and you may find that the
setting cannot be adjusted below a
"+4dB" indication.
Tuner Operation
The AVR40's tuner is capable of tuning
AM, FM and FM Stereo broadcast sta-
tions. Stations may be tuned manually,
or they may be stored as favorite station
presets and recalled from a 30 position
memory.
Station Selection
1. Press the
button
AM/FM
select the tuner as an input.
2. Press the
button
AM/FM
to switch between AM and FM so that the
desired frequency band is selected.
3. Press the
Tuning Mode
select manual or automatic tuning.
When the
indicator is illuminated
AUTO
in the main information display the
tuner will only stop at those stations that
have a strong enough signal to be
received with acceptable quality.
If the
AUTO
displays
ated, the tuner is in a manual mode and
will stop at each frequency increment in
the selected band.
4. To select stations from the front panel
are
press the
indicator is illuminated each press
Hall
AUTO
will cause the tuner to search for the next
highest or lowest frequency station that
has an acceptable signal. When tuning
FM stations in the auto mode, the tuner
will only select Stereo stations. To tune to
mode
the next station, press the button again.
Hall
If the
AUTO
ed, tap the
one frequency increment at a time, or
press and hold it to locate a specific sta-
tion. When the
nates the station is properly tuned and
should be heard with clarity. To listen to
the station in stereo, press the
Mode
indicator illuminates in the front panel
display.
5. To select stations using the remote,
press the
h
to select stations one at a time. After
6d
to
an FM station is selected, the
Mode
the station in stereo, when available.
6d
again
Alternatively, the
››
/
‹‹
scan only those stations with sufficient
strength for proper reception. Each press
button
¸
to
of these buttons will advance the tuner to
the next station. For stereo reception
press the
the
STEREO
NOTE: When the FM reception of a
station is weak, audio quality will be
increased by switching to mono mode by
pressing the
until the
indicator is NOT illumin-
button
Ú
. When
Tuning
indicator is NOT illuminat-
button
Ú
to advance
Tuning
indicator illumi-
TUNED
Tuning
button
¸
until the red
STEREO
buttons
Manual Tune
››
/
‹‹
Tuning
button must be pressed to receive
Automatic Tune
buttons
i
may be used to
button
¸
Tuning Mode
indicator is illuminated.
button
Tuning Mode
indicator goes out.
STEREO
until
¸
Hide quick links:
Advertisement
Table of Contents
