Related Manuals for LOCKLY GUARD ATHENA 228SL
Summary of Contents for LOCKLY GUARD ATHENA 228SL
- Page 1 WWW.LOCKLYPRO.COM PGD228W FOR COMMERCIAL USE & PROFESSIONAL INSTALLATION ATHENA (228SL) (228SW) SLIDE & SWING EDITION INSTALLATION GUIDE...
- Page 3 Preparation Prepare door: remove existing deadbolt or use provided template to bore new holes. Installation template Baseline approximately 1 meter from the ground Ø25 Door Handle Hole...
- Page 4 Step 1 DETERMINE DOOR OPENING DIRECTION There are 4 common door-opening directions, the lockset configuration as shown on each diagram below corresponds to the respective door-opening direction. NOTE: If you're installing a Slide Edition, skip these steps and proceed to Step 3 LEFT IN-SWING DOOR RIGHT IN-SWING DOOR Make sure the latch throw is...
- Page 5 Step 2 ADJUSTING THE LATCH THROW Follow the below steps if you're installing ATHENA SWING EDITION with model and backset size: PGMB118 1 1/8" （28mm）, PGMB138 1 3/8" （35mm), PGMB158 1 5/8"（40mm), PGMB134 1 3/4"（45mm), PGMB238 2 3/8"（60mm） Lockset ships default for RIGHT IN-SWING or LEFT OUT-SWING DOORS. Skip this procedure if your door orientation is as stated.
- Page 6 Step 2 ADJUSTING THE LATCH THROW continued FOR MULTI-POINT LOCKSET MODELS: PGMB138H 1 3/8" (35mm) / PGMB158H 1 5/8" (40mm) / PGMB134H 1 3/4" (45mm) Default setting for these lockset models is for RIGHT IN-SWING or LEFT OUT-SWING DOORS. Skip this procedure if your door orientation is as stated. See Step 1 to determine your door direction.
- Page 7 Step 3 CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS The diagram below shows how to shift the door handle from right to left direction. The default setting of the handle is for right handed door. You do not need to change direction if you have a right handed door.
- Page 8 Step 4 INSTALLING THE LOCKSET Make sure your door is prepared for installation. If you need to drill new holes, please use the supplied template for drilling holes. Before installing the Lockset , confirm the door opening direction (Step 1) and ensure latch throw inclined part is positioned opposite to the opening direction.
- Page 9 Step 4 INSTALLING THE LOCKSET continued Cylinder Adapter (x1) Insert cylinder adapter make sure the arrow (red mark)is at the bottom as shown. Use positioning clamp to hold the cylinder adapter in "+" position. To check if the cylinder adapter is properly installed, insert a phillips screwdriver.
- Page 10 Step 5 ATTACHING EXTERIOR PANEL INSTALLATION PARTS Before installing the key cylinder, make sure your door handle have been adjusted to your door opening direction, see Step 2. Install Key Cylinder 1. Measure door thickness and cut off the key cylinder blade (if necessary). PGD228WSWSS-28;...
- Page 11 Step 5 ATTACHING EXTERIOR PANEL INSTALLATION PARTS continued Install Spindle 1. Select spindle A1/A2 according to door thickness. 2. Install at the center hole of the exterior panel. 3. Insert cotter pin and bend both ends. IMPORTANT: Ensure the handle is correctly positioned according to desired direction (L/R) before bending Cotter Pin(X1) the ends of the cotter pin.
- Page 12 Step 5 ATTACHING EXTERIOR PANEL INSTALLATION PARTS continued Before installing the key cylinder, make sure your door handle have been adjusted to your door opening direction, see Step 2. The illustration below applies for All Athena Slide Edition lockset : PGMB118 1 1/8" (28mm), PGMB138 1 3/8"...
- Page 13 Step 6 INSTALLING THE EXTERIOR AND INTERIOR PANEL Install the exterior panel onto door. Ensure the spindle, lock cylinder, positioning rods and cable are inserted on the correct holes and passed through the llockset. Plug the connection cable of the exterior panel to cable of the interior panel.
- Page 14 Step 7 INSTALL DOOR FRAME AND STRIKE Strike Plate Door Frame Wood door frame or non-broken bridge aluminum metal door frame require drilling drilling template. see illustration on the left for locksets: PGMG118 1-1/8" (30mm), PGMG118H 1-1/8" (30mm), PGMG138 1-3/8" (35mm), PGMG138H 1-3/8"...
- Page 15 Door sensors provide real-time door condition status, such as the ability to verify if the door is securely closed. It sends push notifications to your phone whenever your door opens. Lockly Guard Athena comes with a pre-wired door sensors consisting of two parts: Part (V) - Wired Sensor...
- Page 16 Step 8 INSTALLING DOOR SENSORS continued 1、Peel off the paper layer of the 2、Position the wired sensor to the edge of adhesives from the back of the wired the door, avoiding the door strike plate. sensor. Attach and secure with the adhesives. peel off Peel off the paper layer of the adhesives from the...
- Page 17 Step 9 FINAL CHECK AND BATTERY INSTALLATION 1. Open the battery compartmebt and insert 4 AA batteries. Make sure the batteries are correctly positioned. Battery X4 After removing the battery door Tighten the front and rear with a screwdriver, put the battery panel fixing screws (B) and on, and then tighten the battery door with a screwdriver.
- Page 18 Step 10 DOWNLOAD LOCKLY APP Congratulations! You have completed the Lockly Guard physical lock installation. To complete your setup, download the LocklyPro app from the iOS or Google Play app Store and follow on-screen instructions. Scan or visit Locklypro.com/app...
- Page 19 FCC Radiation Exposure Statement Lockly Guard Link+ complies with FCC radiation exposure limits set forth for an uncontrolled environment. It should be installed and operated with minimum distance 20cm between the radiator &...
- Page 20 INSTALLATION OVERVIEW AND PARTS LIST Exterior Parts List Labeled As Description Adapter Positioning Screw (x1) KM4X6mm Screws (x2) 门框 KM4x25mm Screws (x2) Wooden Door / Aluminum Thermal Barrier Door KA4x16mm Screws (x4) Aluminum Door KA3x16mm Screws（x4) J / L Strike Plate（x1） Silicone Screw Caps (x2) M4 (x1) M1 (x2)
- Page 21 INSTALLATION OVERVIEW AND PARTS LIST Can be used for either Slide or Swing Edition (part included as per door thickness specification (A or B) (A) For 35-50mm Door Thickness Key Cylinder (x1) & Keys (x5) PM4x28mm (x1) Escutcheon KM5x46mm (x2) Cotter Pin Screw 62mm Spindle...
- Page 22 INSTALLATION OVERVIEW AND PARTS LIST Parts individually packed and included according to door specifications Slide Edition Door Strike Kit Swing Edition Door Strike Kit Wooden Door Frame Aluminum Door Frame Aluminum Thermal Barrier Strike Plate (x1) Strike Plate Kit Strike Plate Kit Door Strike Plate Kit KA4X25mm Screws(X3)
- Page 24 FOR COMMERCIAL USE & PROFESSIONAL INSTALLATION We’re here to help! prosales@lockly.com locklypro.com/support © Copyright 2022 Lockly All rights reserved USA Patent No. US 9,881,146 B2 | USA Patent No. US 9,853,815 B2 | USA Patent No. US 9,875,350 B2 | USA Patent No. US 9,665,706 B2 | USA Patent No. US 11,010,463 B2 | AUS Patent No.