Related Manuals for LOCKLY GUARD DEFENDER 238LM
Summary of Contents for LOCKLY GUARD DEFENDER 238LM
- Page 1 WWW.LOCKLYPRO.COM FOR COMMERCIAL USE & PROFESSIONAL INSTALLATION DEFENDER (238LM/238LE) USER MANUAL...
-
Page 2: Table Of Contents
Section 6 - Important Notes Product Overview- Exterior Section 7 - Cleaning Understanding Your New Lock Locking/Unlocking with App Section 8 - Safety Precautions Rebooting Lockly Guard Low Battery Changing the Battery Section 3 - Using Your Smart Lock Configuring Access Entering Programming Mode... -
Page 3: Product Features
The offline access code can allow owners to issue access codes, set the allowed access duration, all without Lockly Guard ever connecting to the internet, so in case of power outage, you can still magically and remotely issue Access Codes without any connection to the web. -
Page 4: Product Overview- Exterior
2.1 Product Overview- Exterior RFID Card Reader Touchscreen Keypad Battery Indicator OK Button Welcome/ Safe Mode Key Hole Exterior Handle Fingerprint Reader Battery Compartment *Operated by 4 X AA size alkaline batteries Program Button Battery Cover 9V alkaline battery Reboot Button SECTION 2.1... -
Page 5: Understanding Your New Lock
For any questions you can always visit http://LocklyPro.com/support for assistance. 2.3 Locking/Unlocking with App Lockly Guard works best with our iOS and Android app. You must have the LocklyPro iOS or Android app installed in order to lock and unlock with smartphone. Download the app by visiting the link below or search "LocklyPro"... -
Page 6: Rebooting Lockly Guard
Press and release the reboot button when you want to reboot the lock. Your Lockly Guard will beep once after reboot. Only reboot when necessary. To reboot, find the reboot button from the bottom of Lockly Guard. You will need something small such as a paperclip, to press the reboot button. Insert the paper clip and press down firmly. -
Page 7: Low Battery
2.5 Low Battery When the battery is in seriously low condition, Lockly Guard will make continuous beeping sounds in addition to the flashing low battery icon on the touch screen. You should replace batteries immediately to avoid your smart lock from shutting down. -
Page 8: Changing The Battery
2.6 Changing the Battery Open the battery compartment cover and insert 4 AA alkaline battery as shown below. • Make sure the batteries are correctly oriented. • Replacement of batteries does not affect programmed data. • Replace only with new batteries. DO NOT mix with used batteries. Use a screwdriver to push the back screw stopper up then loosen the screw. -
Page 9: Configuring Access
3.1 Configuring Access Your new Lockly Guard Access Code can be any combination of 6 to 8 digits. Once a new Access Code is entered, the Default Access Code of 123456 would be deleted. How to Use the Keypad There are a total of five (5) buttons on the keypad as shown in the example image to the left. -
Page 10: Entering Programming Mode
3.2 Entering Programming Mode To enter Programming Mode, remove the battery compartment cover on the interior side of the Lockly Guard to expose the Program button. Short press the program button to enter program- ming mode. Enter administrator fingerprint, RFID... - Page 11 To pair your smart lock to a new mobile phone, download the LocklyPro app on your new mobile phone then use the same account to login to your LocklyPro App on the new mobile device. If you're pairing your Lockly Guard to a new LocklyPro app account, follow the steps below 1.
-
Page 12: Adding An Access Code
3.4 Adding an Access Code Enter the App Access Management settings then tap "Add New User". Select the the type of user you wish to add access, “Trusted User”, “Guests”, “One-Time Access”. For example, select Trusted User, enter the user’s name and set the Access Code. Re-enter the access code, then tap “Confirm”... -
Page 13: Adding A Fingerprint
Not OK Not OK Your Lockly Guard can register up to ninety-nine (99) fingerprints. Please read the follow- ing sections if you want to add or delete fingerprints. We recommend using your app to add fingerprints, however, the following section can show you without using the app. -
Page 14: Adding/Deleting Fingerprints
3.7 Adding/Deleting Fingerprints Fingerprints can only be added or deleted through the App. On the App Access Management, select Fingerprint, then tap "Add New Fingerprint". Scan your finger by lightly placing your designated finger on the sensor until you hear a beep. Lift your finger and repeat the process until the digit “6”... -
Page 15: Fingerprint Scanning Directions
3.8 Fingerprint Scanning Directions The fingerprint sensor equipped in Lockly Guard is loaded with powerful fingerprint algorithms to extract quality features from fingers, even in poor conditions. Placing your finger on the sensor correctly helps consistency in fingerprint recognition. The following directions and tips will guide you on how to scan an optimal fingerprint image. -
Page 16: Fingerprint Scanning Tips & Troubleshoot
3.9 Fingerprint Scanning Tips & Troubleshoot Tips for Fingerprint Enrollment and Recognition • Place your finger to completely cover the sensor with maximum contact surface. • Position the center of your finger (core) to the center of the sensor. • Hold your finger still for more than a second until you hear a beep. •... -
Page 17: Checking/Deleting An Rfid Card
3.10 Adding an RFID card(Continued) The Lockly Guard keypad will lit up and show the number sequence of the RFIDs to be added. Place the card into RFID card reading area. • When RFID card is successfully added, keypad will display PASS followed by a beep. The display screen will exit automatically and lit up with PIN Genie screen. -
Page 18: Unlocking With Access Codes
Ten consecutive wrong attempts will put Lockly Guard in “Safe Mode”. (See Section 4.6) Lock your Lockly Guard by pressing the OK Button anytime when the door is closed. Lockly Guard will also auto-lock after five (5) seconds after unlocking and opening. -
Page 19: Unlocking/Locking With Fingerprints
Try again or use another registered fingerprint. For best fingerprint scanning practices, see Section 3.8. Locking To lock the Lockly Guard, for the Latch Mortise Edition, press the OK Button anytime when the door is opened. For other editions, you will need to man- ually lift the handle to lock it from exterior assembly. -
Page 20: Unlocking With Rfid
4.3 Unlocking with RFID Push down the handle and open the door after it chimed. Light up the screen by touching the keypad. SECTION 4.3... -
Page 21: Locking/Unlocking With Physical Key
4.4 Locking/Unlocking with Physical Key Exterior View To unlock your Lockly Guard using the physical key (supplied. Insert your key and turn clockwise or counter clockwise to lock or unlock the door. 4.5 Unlock with QR Code If you have multiple Lockly door locks, you can use the Lockly app code scanner to unlock. -
Page 22: Safe Mode
4.6 Safe Mode Lockly Guard will enter Safe Mode when ten (10) consecutive wrong Access Codes are entered within 5 minutes. When in Safe Mode, the lock status icon will start to flash. To disable Safe Mode, you must unlock the door using the correct fingerprint or enter the correct Access Code twice in a row. - Page 23 Option 1 - Lockly Guard Bluetooth App Use the app that is synced to your Lockly Guard to disable Safe Mode by unlocking the door. If you have not downloaded the app to use with your smart lock, you won’t be able to use this option to disable Safe Mode.
-
Page 24: Locking From The Outdoor
4.7 Locking from the Outdoor Lockly Guard smart lock will automatically lock once your door is closed. You can set the Auto Lock timer or you may opt to disable this feature through the APP. When Auto-lock is disabled, you can quickly lock your door with One-Touch anywhere on the keypad or simply press the . -
Page 25: Rain Mode
To protect the lock and extend battery life, you can setup your Lockly Guard to enter Rain Mode to shut off keypad and fingerprint reader whenever rain or water is detected. -
Page 26: Shine Mode
4.9 Shine Mode Lockly Guard touchscreen keypad brightness was designed for optimum battery life. However, some users may need to adjust the brightness to their convenience to enter access codes. Swipe your fingers across the keypad to light up to its normal brightness. -
Page 27: Offline Access Code
OAC are issued to the guest by asking them to enter 4-12 digit number after a double randomly generates the Offline Access Code - click on the . Your Lockly Guard which can be shared to your guests together with the instructions generated using the LocklyPro app. , touchscreen will display numbers on Fixed Digit mode,... - Page 28 It is very crucial that you do not lose this card. Please store this card safely as you will need the default Activation Code on that card to master reset your lock in case, for any reason, you have lost the phone paired to Lockly Guard and also forgot your Access Code.
- Page 29 7.1 Cleaning Making sure your Lockly Guard is clean is best practice to ensure optimal product use. Follow the DOs and DON’Ts below. • Rinse the touchscreen with warm water prior to cleaning. • Use the application of soap with a damp, lukewarm cloth.
- Page 30 FCC Warning： This device complies with Part 15 of the FCC Rules. Operation is subject to the follow- ing two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Page 31 applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: 1. L’appareil ne doit pas produire de brouillage; 2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. IC Radiation Exposure Statement This equipment meets the exemption from the routine evaluation limits in section 2.5 of RSS-102.
- Page 32 For digital versions and instructional videos, please visit the following link LocklyPro.com/support © Copyright 2022 Lockly Guard All rights reserved USA Patent NO. US 9,881,146 B2 |USA Patent NO. US 9,853,815 B2 |USA Patent NO. US 9,875,350 B2 | USA Patent NO. US 9,665,706 B2 | USA Patent NO. US 11,010,463 B2 | AU Patent NO.