Related Manuals for LOCKLY GUARD VISION DUO
Summary of Contents for LOCKLY GUARD VISION DUO
- Page 1 FOR COMMERCIAL USE & PROFESSIONAL INSTALLATION WWW.LOCKLYPRO.COM PGD698D VISION DUO (698D) INTERCONNECTED EDITION INSTALLATION GUIDE ( a p p l i c a t i o n i n p r o g r e s s )
- Page 2 GET THE MOST OUT OF YOUR LOCKLY GUARD ™ Get the latest user/installation manuals , instructional videos, and FAQs SCAN or VISIT Locklypro.com/698D...
- Page 3 Welcome! This guide will walk you through step-by-step how to install and get Lockly Guard up and running. Installation generally ™ takes less than 30 minutes. If you have any questions please call our VIP hotline (855) 562-5599 for help.
- Page 4 Preparation To complete the installation you will need: Flathead Screwdriver Phillips Screwdriver Tape measure or ruler Optional Pliers Screwdriver with drill bits Drilling maybe required to install this lock. If you are installing your lock on a brand new door, a drill is required if there are no holes prepared for lock installation.
-
Page 5: Important Notice
Preparation continued Remove existing door hardware, latch or deadbolts before installing the new lock. Use provided template to bore new holes if needed. Measure and confirm 1- 3/8"—2" your door is between (35mm—50mm) 1-3/8" - 2" ( 35mm - 2-1/8" 50mm). - Page 6 Step 1 INSTALLING THE LOCKSET Measure the distance between center of front door hole to the edge of your door hole to determine the backset. Adjust latchbolt deadbolt according to the backset of your door. Deadbolt Adjustment 2-3/8"(60mm) 2-3/4"(70mm) I. Push the crank (a) to III.
- Page 7 Step 1 INSTALLING THE LOCKSET continued After adjusting the latchbolt , determine the orientation of the latchbolt. Determine the orientation of latchbolt. Facing the door exterior, install the latchbolt according to the opening direction of your door. LEFT OUT-SWING DOOR RIGHT OUT-SWING DOOR Inside Inside...
- Page 8 Step 2 CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS The lock ships with handle default for right in-swing or left out-swing door. Check the diagram below if you are unsure of you door orientation. RIGHT IN-SWING DOOR INTERIOR LEFT IN-SWING DOOR Hinge Side LEFT OUT-SWING DOOR...
- Page 9 Step 2 CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS continued Rotate the handle 180° to the other Confirm that your installation was side of the lock. complete by checking if the pins are flush against the handle, and Using your fingers, press the two pins has popped out.
- Page 10 Step 2 CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS continued At the back of the exterior assembly, remove the screw on point "R". Align the screw hole on point "L" then insert the removed screw and tighten.
- Page 11 Step 2 CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS continued Changing the Interior Handle Orientation Remove the handle retaining screw and detach the handle. Rotate the handle 180° as shown. Insert the handle retaining screw and tighten using a screw driver.
- Page 12 Step 3 PREPARING LOCK FOR INSTALLATION Carefully prepare the lock and ensure the required parts ( ) have been properly attached before installing to door. Slotted Barrel Extension E should be installed accor- ding to upper door hole distance to the bottom door hole (4"...
- Page 13 Step 4 INSTALLING THE LOCK (EXTERIOR) Install fire shield as shown. Note: The fire hood should not press the wire. Use a screwdriver to secure the cables in the fire hood. Ensure that the cables are routed out of the U-shaped slot and the fire hood does not press cables.
- Page 14 Step 4 INSTALLING THE LOCK (EXTERIOR) continued Ensure is securely installed on the correct Exterior position, then insert to top door hole, passing through below part While aligning the lock straight up-and-down, pass the wiring cable under the latchbolt then ensure the Slotted Barrel Extension passes through the hole on the lower part of the deadbolt...
- Page 15 Step 5 INSTALLING INTERCONNECTION PLATE GEAR Select interior cover plate according to door hole distance and install on to door. 4” use cover plate 5.5” use cover plate Insert Positioning Rods into the holes to the left and right of the Spindle .
- Page 16 Step 5 INSTALLING INTERCONNECTION PLATE GEAR continued Install fire shield as shown. Ensure that the cables are routed out of the U-shaped slot and the fire hood does not press cables. Ensure the rods on interior cover plate is inserted on the holes of the deadbolt.
- Page 17 Step 5 INSTALLING INTERCONNECTION PLATE GEAR continued Secure interior cover plate with screws . Remove the position rods and replace them with screws Tighten clockwise until the mounting plate is secure. Hole for screw for 5.5" Secure with Hole for screw for 4"...
- Page 18 Step 5 INSTALLING INTERCONNECTION PLATE GEAR continued Select the side of the interconnection gear according to door handle orientation Left or Right . Insert torque blade to plate according the distance between the latchbolt and deadbolt . Insert for 5.5" Insert for 4"...
- Page 19 Step 5 INSTALLING INTERCONNECTION PLATE GEAR continued Install interconnection plate onto door. Ensure the torque blade is inserted horizontally to the deadbolt. The spindle must pass through the plate. Secure the plate with screws...
-
Page 20: Connect Cable
Step 6 INSTALLING INTERIOR ASSEMBLY (N) Connect cable by hand. Plug into , match red side of plug with red on socket - insert tightly. Secure the lock interior with 3 screws Do not touch pins inside* Call our Customer Care Hotline (669) 500-8835, for help if the pins are not centered or bent. - Page 21 Step 6 INSTALLING INTERIOR ASSEMBLY (N) continued Align the spindle to the lock interior and attach the Interior lock to the interconnection plate. Gently push some of the excess cable through the rectangular hole into the door. Place the remaining cable inside the interior assembly and ensure it sits securely onto the interconnection plate gear.
- Page 22 Step 6 INSTALLING INTERIOR ASSEMBLY (N) continued Insert 8 AA batteries into the lock Secure the battery by sliding the by aligning the positive (+) and cover over the lock and negative (-) markings on the turning the screw clockwise on batteries to the battery chamber.
- Page 23 It also sends push notifications to your phone whenever your door opens and enables voice control. Lockly Guard Vision Duo (698D) comes with a pre-wired door sensors consisting ™ of two parts: Part...
- Page 24 Step 7 PREPARING DOOR SENSORS FOR INSTALLATION continued When you are installing the door sensors, make sure the arrow of the wired sensor is placed next to the arrow of the sensor magnet as close as possible. LEFT RIGHT IMPORTANT: Do not install the sensor close to the strike plate 2-3/8"...
- Page 25 Step 7 PREPARING DOOR SENSORS FOR INSTALLATION continued The interior assembly comes with the pre-installed wired door sensor setup for a right/left swing doors with 2-3/4" (70mm) backset*. Trim excess part for doors with 2-3/8" (60mm) backset as shown below. Trim excess here for 2 ⅜"...
- Page 26 Step 8 INSTALLING THE DOOR STRIKE It is recommended that you use the included strike plate. However, if you find the deadbolt and latchbolt works with your existing strike plate free of any binding or resistance you can use it. Regardless of which strike plate used, deadbolt and latchbolt needs to operate smoothly, free of any binding or resistance.
- Page 27 Step 9 INSTALLING THE DOORS SENSOR Make sure you have prepared the door sensors for installation according to Step 7 Peel off the paper layer of the Position the wired sensor adhesives from the back of the the edge of the door, avoiding wired sensor the door strike plate.
- Page 28 Step 10 DOWNLOAD LOCKLYPRO APP & UNIQUE ACTIVATION CODE Congratulations! You have completed the Lockly Guard Vision Duo (698D) ™ physical lock installation. To complete your setup, download the LocklyPro app from the iOS or Google Play app Store and follow on-screen instruc- tions.
- Page 29 Bluetooth and Wi-Fi enabled ™ ® Vision Connect Lockly Guard Smart Lock Wi-Fi Router 3 feet (1 meters) 100 Feet (30 meters) or less off the ground TIP: Sometimes distances between hub and lock can vary due to circumstances.
- Page 30 Once you have confirmed that your Wi-Fi Hub is ready to connect to your lock, open the LocklyPro App from your smartphone. Make sure you are standing between the Wi-Fi hub and Lockly Guard smart lock, then Add New Device and follow the on screen instructions.
- Page 31 Step 11 SETTING THE VISION CONNECT HUB continued Ensure the TF card that comes Connect LAN cable to closest Wi-Fi with Vision Connect is properly router to the Lockly Guard lock ™ inserted. (<100ft). Always keep the Antenna on UP position...
- Page 32 ™ Launch the LocklyPro App and select "add a new device", then select Lockly Guard Vision Duo (698D). You will be prompted to ™ scan the QR code from the Activation Card or Vision Connect Hub (located at the bottom).
-
Page 33: Led Indicators
Step 13 VISION CONNECT STATUS & TROUBLESHOOTING LED INDICATORS STATUS After connecting LAN cable and power adapter, wait for Power ON/ Solid red ON 2mins for Vision Connect to Successfully paired self calibrate. Yellow slow blinking Network connected READY TO CONNECT If you experience any of the following, power down and disconnect hub, repeat connection process Pairing / Network... - Page 34 Step 14 CONNECTING YOUR LOCKLY GUARD™ VISION DUO (698D) The App will take you through the following steps, make sure the smart lock has been properly installed. You will need your activation card that is included in the box to proceed.
- Page 35 Step 14 CONNECTING YOUR LOCKLY GUARD™ VISION DUO (698D) continued Find fhe Activation Card Scan the QR Code Scan the QR Code 9:44 AM 100% 9:44 AM 100% ●●●●● AT&T 9:45 AM 100% ●●●●● AT&T ●●●●● AT&T KEEP THIS CARD!
- Page 36 Step 14 CONNECTING YOUR LOCKLY GUARD™ VISION DUO (698D) continued Set the Admmin Code Match Admmin Code Successfully Connected 9:46 AM 100% ●●●●● AT&T 9:46 AM 100% 9:47 AM 100% ●●●●● AT&T ●●●●● AT&T Successfully Connected ●●●●● AT&T 9:48 AM...
- Page 37 FCC Warning： This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interfer- ence that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
- Page 38 L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: 1. L’appareil ne doit pas produire de brouillage; 2.
- Page 39 This lock can be installed for both right swing and left swing doors. The lock ships ready for a right swing door installation. If you wish to change the orientation of the lock for a INSTALLATION OVERVIEW & PARTS LIST Left Swing door, follow instructions on Installation Guide (Step 2).
-
Page 40: Important Notes
WAIT. IMPORTANT NOTES Lockly Guard installs differently from other door locks. Professional installer(s) and locksmiths must read and follow Lockly Guard installation and user manuals to prevent damaging the product. Failure to do so may also result in the smart lock not responding correctly to lock and unlocking commands and will require re-installation. -
Page 41: We're Here To Help
FOR COMMERCIAL USE & PROFESSIONAL INSTALLATION We’re here to help! prosales@lockly.com locklypro.com/support © Copyright 2022 Lockly All rights reserved US Patent NO. US 9,881,146 B2 | US Patent NO. US 9,853,815 B2 | US Patent NO. US 9,875,350 B2 | US Patent NO. US 9,665,706 B2 | US Patent NO.