Harman Kardon DVD 27 Owner's Manual page 10

REMOTE CONTROL FUNCTIONS REMOTE CONTROL FUNCTIONS
0 Power On: Turns on the player when it is in
Standby mode (Harman Kardon logo appears on-
screen).
1 Open/Close: Press to open or close the
disc tray.
2 Audio Select: Press to access various audio lan-
guages on a DVD (if the DVD contains multiple audio
streams). This button may also allow you to access
other audio formats on DVD discs, such as linear PCM
or Dolby Digital 5.1 tracks (or other formats), if they've
been recorded on the disc.
3 Clear: Press this button to remove on-screen
menus or banners from the display screen. Press this
button to clear the current play order displayed next to
a track while programming a playlist. In Stop mode
and with all menus and banners removed from the
display, press and hold this button for five seconds
to reset all settings to their factory defaults.
4 Playlist: Press this button to access the Playlist
on-screen menu, which enables you to change the
order in which tracks are played on a CD. (See page
33 for more information on creating and playing
playlists.)
5 Repeat: Each press of this button changes the
playback mode to repeat a chapter or track or the
entire disc. A repeat icon will appear in the upper right
corner of the screen indicating the current repeat
mode. If the Player Information Screen is active, the
changes will be displayed on screen.
6 A-B Repeat: Press this button to enter the start-
ing point of a section on a disc you wish to repeat.
The second press enters the end of the selection to
be repeated. Once the "A" (start) and "B" (end) points
have been entered the player will repeat the selection
until the Play Button L3 is pressed or the disc is
stopped. If the Player Information Screen is active, the
changes will be displayed on screen.
7 Random: Each press of this button starts or
stops playback in random order. The Random function
is only available when playing CDs, but not when a
Playlist is active (the Player Information screen indi-
cates Programmed Order on the Playlist line).
8 Info: Press once to access the Player Information
menu for information on the current disc and the play-
back mode settings. Press again to remove informa-
tion from screen. See page 17 for more information
on the Player Information menu.
10 REMOTE CONTROL FUNCTIONS
9 Setup: Press this button to use the DVD 27's
on-screen menu system to adjust the player's configu-
ration settings. Note that the Info Button 8 must
be pressed to access the DVD 27's Player Information
menu to obtain detailed disc information, and to con-
figure the playback mode of the disc.
A Previous Step/Skip: Press this button once to
skip back to the beginning of the current chapter on
a DVD or track on a CD. Press it again to continue
to skip back through the previous chapters or tracks.
After first pressing the Pause Button J, press this
button to step backwards through a DVD or VCD as a
series of still image frames.
B Search/Slow Reverse: This button initiates fast
or slow play in the reverse mode. For fast reverse play,
each press of the button when playing DVD or VCD
discs changes the speed as indicated by the number
appearing in the upper right corner of the screen. For
slow reverse play, first press the Pause Button J
and each subsequent press of this button will change
the slow play speed as indicated by the number
appearing in the upper right corner of the screen.
C Angle: Press this button to change the camera
angle on discs programmed for multiple-angle views.
When a JPEG is being displayed, pressing the Angle
Button C repeatedly causes the on-screen image
to rotate clockwise by 90 degrees each press. The
current orientation in degrees will be displayed in
the upper right corner of the screen.
D M NK LNavigation Buttons: Use to move
the cursor in the on-screen menu system.
E Light: Press to illuminate the buttons on the
remote controller.
F Video Off: Press this button to turn off the video
output for improved audio performance when playing
discs. Press it again to view the on-screen menus. It
is highly recommended that you use this function to
prevent "burn-in" of your plasma video display.
G Dimmer: Press to change the brightness of the
front panel display or to turn the display off completely
in the following order: FULL BRIGHTNESS
BRIGHTNESS OFF FULL BRIGHTNESS
H Progressive Scan/Interlaced Button: Each
press of this button selects between the progressive
scan and interlaced modes for the Component Video
Outputs ∞.
I Enter: Press this button to enter a setting in the
DVD 27 menu system or to confirm a menu selection
choice in a disc's on-screen menu.
J Pause: Press this button to pause the disc and
freeze the picture during DVD or VCD playback, or to
pause the playback of a CD. To play a DVD or VCD in
the slow, forward or reverse mode, first press this but-
ton and then press either the Search/Slow Forward
M or Reverse Button B.
K Zoom: Press this button to zoom in on the
image from a DVD, VCD or JPEG image. The image
may be expanded by a factor of x2, x3, x4 or x5.
Once the on-screen indication of the zoom ratio disap-
pears from the screen you may use the Navigation
Buttons D to explore the picture.
L Play: Press this button to begin the playback of
a disc, or to resume normal playback when a disc has
been paused or scanned.
M Search/Slow Forward: This button initiates fast
or slow play in the forward mode. For fast forward play,
each press of the button when playing DVD or VCD
discs changes the speed as indicated by the number
appearing in the upper right corner of the screen. For
slow forward play, first press the Pause Button J
and each subsequent press of this button will change
the slow play speed as indicated by the number
appearing in the upper right corner of the screen.
N Stop: When a DVD is playing, press this button
once to place the disc in the Resume mode, which
means that playback will stop. However, as long as
the disc drawer is not opened, playback will continue
from the point where the disc was stopped when the
Play Button L3 is pressed again, as indicated by
the LAST SCENE message (for DVDs) or the
RESUME message (for CDs, MP3 files, JPEG files
and VCDs with PBC) in the Information Display
Resume will not operate for WMA files or VCDs that
do not have playback control. Pressing the button
twice will stop the disc and play will start from the
beginning of the disc when the Play Button L3
is pressed again.
O Next Step/Skip: Press this button once to
advance to the beginning of the next chapter on a
DVD or track on a CD. Press it again to continue to
advance through the remaining chapters or tracks.
After first pressing the Pause Button J, press this
button to step through a DVD as a series of still-image
frames.
P Disc Menu: While a DVD is playing, press this
button to view the disc's main menu.
HALF
Q Status: Press while a disc is playing to view the
on-screen status banner display. The first press will
display the current title and chapter, the play mode
icon and the elapsed time, along with a "temperature
bar" display of the time elapsed. You may use the
M NK LNavigation Buttons D and the Enter
Button I to select and change the current title
or chapter, or the time display. The Status Banner is
only available for DVDs and VCDs when PBC is turned
off. Press the button one more time to remove the
status displays from the screen. More detailed infor-
mation about the disc is available by pressing the
Info Button 8.
R Numeric Keys: Press these buttons to enter a
number.
.