Summary of Contents for Hand Held Products IMAGETEAM 3800E
Page 1
IMAGETEAM™ 3800E Linear Imager Engine ™ User’s Guide...
Page 2
Hand Held Products. Hand Held Products shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material.
Page 3
Information on FCC Class B and Canadian ICES-003 This equipment has been tested at the component level and found to meet the limits for a Class B digital device pursuant to part 15 of the FCC Rules and Canadian ICES-003. Users are responsible for testing for compliance in the end product.
Table of Contents Chapter 1 - Terminal Interfaces About This Manual ... 1-1 Scanner Identification... 1-1 Mounting Information ... 1-2 Specular Zone... 1-3 Terminal ID ... 1-3 Supported Terminals... 1-5 Keyboard Wedge Connection... 1-6 Keyboard Style ... 1-7 Keyboard Modifiers... 1-7 Serial Port Connection...
Page 6
Chapter 3 - Data Editing Prefix/Suffix Overview... 3-1 To Add a Prefix or Suffix: ... 3-2 To Clear One or All Prefixes or Suffixes:... 3-3 To Add a Carriage Return Suffix to all Symbologies ... 3-3 Prefix Selections... 3-4 Suffix Selections ... 3-4 Symbology Chart ...
Page 9
Chapter 6 - Visual Menu Visual Menu Introduction ... 6-1 Temporary Visual Menu Configuration ... 6-1 Installing Visual Menu from the Web... 6-1 Chapter 7 - Interface Keys Keyboard Function Relationships... 7-1 Supported Interface Keys ... 7-3 Chapter 8 - Utilities To Add a Test Code I.D.
Terminal Interfaces The IMAGETEAM™ (IT) 3800E is a high performance linear imaging scanner engine from Hand Held Products. Linear imaging technology is defined by a bright and sharply focused aiming line, high resolution imaging, and fast reading speed. About This Manual This User’s Guide provides installation and programming instructions for the...
Terminal ID IMAGETEAM 3800E scanners are factory programmed for a serial port interface, 9600 baud, even parity, 7 data bits, 1 stop bit. If this is your interface and you do not need to modify the settings, skip to Chapter 2 - Output.
Page 16
Discard code on the back cover, scan the Terminal ID bar code, scan the digits, and the Save code again. Terminal ID Save Note: After scanning one of these codes, you must re-boot your computer. 1 - 4 IMAGETEAM™ 3800E User’s Guide...
This selection can only be used with systems that have an LED which notes the Caps Lock status. Automatic Caps Lock Keyboard Modifiers This modifies special keyboard features, such as CTRL+ ASCII codes and Turbo Mode. IMAGETEAM™ 3800E User’s Guide 1 - 7...
Page 20
Default = Off Turbo Mode On * Turbo Mode Off Numeric Keypad Mode: Sends numeric characters as if entered from a numeric keypad. Default = Off Numeric Keypad Mode On * Numeric Keypad Mode Off 1 - 8 IMAGETEAM™ 3800E User’s Guide...
Connect Mode On * Automatic Direct Connect Mode Off Serial Port Connection All communication parameters between the scanner and terminal must match for correct data transfer through the serial port using RS-232 protocol. IMAGETEAM™ 3800E User’s Guide 1 - 9...
Baud Rate sends the data from the scanner to the terminal at the specified rate. The host terminal must be set for the same baud rate as the scanner. Default = 9600. 1200 4800 19200 1 - 10 2400 * 9600 38400 IMAGETEAM™ 3800E User’s Guide...
RS-232 handshaking is a set of rules concerning the exchange of data between serially communicating devices. Default = RTS/CTS, XON/XOFF and ACK/ NAK Off RTS/CTS On * RTS/CTS Off XON/XOFF On * XON/OFF Off ACK/NAK On * ACK/NAK Off IMAGETEAM™ 3800E User’s Guide 1 - 13...
Default = 25 inches/second. Wand Emulation Polarity The Polarity can be sent as standard with black bars high, or reversed with white bars high. Default = Black High. * Black High 1 - 14 * 25 White High IMAGETEAM™ 3800E User’s Guide...
When in Wand Emulation mode, you must set the scanner’s idle state to match the idle state for the device to which the scanner is connected. Default = Idle High . * Idle High Idle Low IMAGETEAM™ 3800E User’s Guide 1 - 15...
Setting a reread delay protects against accidental rereads of the same bar code. Longer delays are effective in minimizing accidental rereads at POS (point of sale). Use shorter delays in applications where repetitive bar code scanning is required. Default = Short. IMAGETEAM™ 3800E User’s Guide 2 - 3...
Extra Long Good Read Delay This sets the minimum amount of time before the scanner can read another bar code. Default = No Delay. * No Delay Short Delay Medium Delay Long Delay 2 - 4 IMAGETEAM™ 3800E User’s Guide...
Caution: Do not select Manual Trigger unless you have provided a means to trigger the scanner. The 3800E does not have a manual trigger switch. To operate in this trigger mode, users must provide a switch to ground the trigger line or use serial trigger commands via the serial...
Page 34
Caution: Do not select Presentation Mode unless you have provided a means to trigger the scanner. The 3800E does not have a manual trigger switch. To operate in Presentation Mode with low ambient light, users may have to provide a switch to ground the trigger line or use serial trigger commands via the serial port interface Commands"...
Step 3. Scan the 2 hex digits from the Programming Chart inside the back cover or scan 9, 9 for all symbologies. IMAGETEAM™ 3800E User’s Guide Scanned Data Suffix...
Page 36
Chart (page 3-6) for the CR (carriage return). Step 5. Scan 0, D from the Programming Chart (inside back cover). Step 6. Scan Save, or scan Discard to exit without saving. 3 - 2 IMAGETEAM™ 3800E User’s Guide (page 3-5)
Scan the following bar code if you wish to add a Carriage Return Suffix to all symbologies at once. This action first clears all current suffixes, then programs a carriage return suffix for all symbologies. IMAGETEAM™ 3800E User’s Guide Add CR Suffix All Symbologies...
You can program up to 99 steps (of 5 ms each). Scan the Intercharacter Delay bar code below, then scan the number of steps, and the SAVE bar code from the inside back cover. IMAGETEAM™ 3800E User’s Guide 3 - 7...
To remove this delay, scan the Delay Length bar code, and set the number of steps to 00. Scan the SAVE bar code from the inside back cover. 3 - 8 Prefix Scanned Data Intercharacter Delay page 3-5). IMAGETEAM™ 3800E User’s Guide Suffix Intercharacter Delay Delay Length...
To remove this delay, scan the Intermessage Delay bar code, then set the number of steps to 00. Scan the SAVE bar code from the inside back cover. IMAGETEAM™ 3800E User’s Guide If you make an error while scanning the...
Refer to the Format Editor Commands Chart bols that represent the command you want to enter. 94 alphanumeric characters may be entered for each symbology data format. Step 7. Scan Save to save your entries. IMAGETEAM™ 3800E User’s Guide page 4-4. (page 4-4).
F7 Move the cursor to the beginning of the data string. Syntax = F7. EA Move the cursor to the end of the data string. Syntax = EA 4 - 2 page 1-5), Code I.D. and the page 3-6, and nn is the numeric IMAGETEAM™ 3800E User’s Guide page 3-6.) page 3-6.)
Page 47
If character is not numeric, format is aborted. Syntax = EC . ED Check to make sure there is a non-numeric ASCII character at the current cursor position. If character is numeric, format is aborted. Syntax = ED . IMAGETEAM™ 3800E User’s Guide page 3-6.) ...zz...
When Data Formatter is turned off, the bar code data is output to the host as read (including prefixes and suffixes). Choose one of the following options. Default = Data Formatter On. * Data Formatter On, but Not Required Data Formatter Off 4 - 4 IMAGETEAM™ 3800E User’s Guide...
The scanner will scan the next bar code, formatting the data with the selected alternate format, then revert immediately to the primary format. Alternate Data Format 1 Alternate Data Format 2 Alternate Data Format 3 IMAGETEAM™ 3800E User’s Guide 4 - 5...
All Symbologies If you want to decode all the symbologies allowable for your scanner, scan the All Symbologies On code. All Symbologies On IMAGETEAM™ 3800E User’s Guide • EAN/JAN • IATA Code 2 of 5 • Interleaved 2 of 5 •...
* On Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/Stop characters. Default = Don’t Transmit . Transmit * Don’t Transmit 5 - 2 IMAGETEAM™ 3800E User’s Guide...
Codabar symbol having a “D” start character, adjacent to a symbol having a “D” stop character. In this case the two messages are concatenated into one with the “D” characters omitted. Default = On. Start Stop Start Stop Character Codabar A12D D34A IMAGETEAM™ 3800E User’s Guide 5 - 3...
Discard on the back cover, scan the Minimum or Maximum bar code, scan the correct digits, and Save again. Minimum (Default =4) 5 - 4 Max. length = 20 Max. length = 15 Maximum (Default =60) IMAGETEAM™ 3800E User’s Guide...
* On Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/Stop characters. Default = Don’t Transmit. Transmit * Don’t Transmit IMAGETEAM™ 3800E User’s Guide 5 - 5...
Code 39 bar codes printed with a check character, and will transmit this character at the end of the scanned data. Default = No Check Character. * No Check Character Validate, but Don’t Transmit Validate and Transmit 5 - 6 IMAGETEAM™ 3800E User’s Guide...
Note: If you make an error while scanning the digits (before scanning Save), scan Discard on the back cover, scan the Minimum or Maximum bar code, scan the correct digits, and Save again. Minimum (Default =0) IMAGETEAM™ 3800E User’s Guide Max. length = 20 Max. length = 15 Maximum (Default =48)
Default = Off. Base 32 Base 32 is a form of the Code 39 symbology used by Italian pharmacies. This is also known as PARAF. 5 - 8 * Off * Off IMAGETEAM™ 3800E User’s Guide...
ESC %A Character pairs /M and /N decode as a minus sign and period respectively. Character pairs /P through /Y decode as 0 through 9. * Full ASCII On IMAGETEAM™ 3800E User’s Guide SPACE 0 < %G L %H M >...
Interleaved 2 of 5 bar codes printed with a check digit, and will transmit this digit at the end of the scanned data. Default = No Check Digit. * No Check Digit Validate, but Don’t Transmit Validate and Transmit 5 - 10 IMAGETEAM™ 3800E User’s Guide...
When Strict Decoding is used, the scanner only reads bar codes that are close to spec. This reduces the number of misreads, but also reduces the tolerance for bar codes that are slightly out of spec. IMAGETEAM™ 3800E User’s Guide Max. length = 20 Max. length = 15...
Discard on the back cover, scan the Minimum or Maximum bar code, scan the correct digits, and Save again. Minimum (Default =0) 5 - 12 Max. length = 20 Max. length = 15 Maximum (Default =80) IMAGETEAM™ 3800E User’s Guide...
Note: If you make an error while scanning the digits (before scanning Save), scan Discard on the back cover, scan the Minimum or Maximum bar code, scan the correct digits, and Save again. Minimum (Default =4) IMAGETEAM™ 3800E User’s Guide Max. length = 20 Max. length = 15 Maximum (Default =48)
Discard on the back cover, scan the Minimum or Maximum bar code, scan the correct digits, and Save again. Minimum (Default =4) 5 - 14 Max. length = 20 Max. length = 15 Maximum (Default =48) IMAGETEAM™ 3800E User’s Guide...
Note: If you make an error while scanning the digits (before scanning Save), scan Discard on the back cover, scan the Minimum or Maximum bar code, scan the correct digits, and Save again. Minimum (Default =4) IMAGETEAM™ 3800E User’s Guide Max. length = 20 Max. length = 15 Maximum (Default =80)
* On Check Digits Required This option sets whether 1 or 2 check digits are required with Code 11 bar codes. Default = Two Check Digits. One Check Digit * Two Check Digits 5 - 16 IMAGETEAM™ 3800E User’s Guide...
Note: If you make an error while scanning the digits (before scanning Save), scan Discard on the back cover, scan the Minimum or Maximum bar code, scan the correct digits, and Save again. Minimum (Default =4) IMAGETEAM™ 3800E User’s Guide Max. length = 20 Max. length = 15 Maximum (Default =80)
Code 128 <Default All Code 128 Settings> Code 128 * On <GS> Substitution When enabled, the scanner substitutes a <GS> for Function Character 1 when decoding EAN 128. Default =Off. * Off 5 - 18 IMAGETEAM™ 3800E User’s Guide...
Note: If you make an error while scanning the digits (before scanning Save), scan Discard on the back cover, scan the Minimum or Maximum bar code, scan the correct digits, and Save again. Minimum (Default =0) IMAGETEAM™ 3800E User’s Guide Max. length = 20 Max. length = 15 Maximum (Default =80)
Telepen Output is selected, the scanner reads symbols with start/stop pattern 1 and decodes them as compressed numeric with optional full ASCII (start/stop pattern 2). Default = AIM Telepen Output. * AIM Telepen Output Original Telepen Output 5 - 20 IMAGETEAM™ 3800E User’s Guide...
Note: If you make an error while scanning the digits (before scanning Save), scan Discard on the back cover, scan the Minimum or Maximum bar code, scan the correct digits, and Save again. Minimum (Default =1) IMAGETEAM™ 3800E User’s Guide Max. length = 20 Max. length = 15 Maximum (Default =60)
Default = On. * On Number System The numeric system digit of a UPC symbol is normally transmitted, but the unit can be programmed so it will not transmit it. Default = On. * On 5 - 22 IMAGETEAM™ 3800E User’s Guide...
Addenda Required When Addenda Required is set to on, the scanner will only read UPC A bar codes that have addenda. Default = Off. IMAGETEAM™ 3800E User’s Guide * 2 Digit Addenda Off * 5 Digit Addenda Off * Off...
When UPC Strict Decoding is used, the scanner only reads bar codes that are close to spec. This reduces the number of misreads, but also reduces the tolerance for bar codes that are slightly out of spec. * Off 5 - 24 IMAGETEAM™ 3800E User’s Guide...
UPC E0 Off UPC E1 On * UPC E1 Off UPC E Expand UPC E Expand expands the UPC E code to the 12 digit, UPC A format. Default = Off. * Off IMAGETEAM™ 3800E User’s Guide 5 - 25...
Default = On. * On Number System The numeric system digit of a UPC symbol is normally transmitted, but the unit can be programmed so it will not transmit it. Default = On. * On 5 - 26 IMAGETEAM™ 3800E User’s Guide...
Addenda Required When Addenda Required is set to on, the scanner will only read UPC E bar codes that have addenda. Default = Off. IMAGETEAM™ 3800E User’s Guide * 2 Digit Addenda Off * 5 Digit Addenda Off * Off...
When this feature is on, there is a space between the data from the bar code and the data from the addenda. When turned off, there is no space. Default = On. * On 5 - 28 IMAGETEAM™ 3800E User’s Guide...
EAN/JAN 13 * On Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On. * On IMAGETEAM™ 3800E User’s Guide 5 - 29...
When Addenda Required is set to on, the scanner will only read EAN/JAN 13 bar codes that have addenda. Default = Off. 5 - 30 * 2 Digit Addenda Off * 5 Digit Addenda Off * Off IMAGETEAM™ 3800E User’s Guide...
When turned off, there is no space. Default = On. * On ISBN Enable This symbology allows the scanner to read ISBN codes on books. Default = Off. * Off IMAGETEAM™ 3800E User’s Guide 5 - 31...
EAN/JAN 8 * On Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On. * On 5 - 32 IMAGETEAM™ 3800E User’s Guide...
Addenda Required When Addenda Required is set to on, the scanner will only read EAN/JAN 8 bar codes that have addenda. Default = Off. IMAGETEAM™ 3800E User’s Guide * 2 Digit Addenda Off * 5 Digit Addenda Off * Off...
When this feature is on, there is a space between the data from the bar code and the data from the addenda. When turned off, there is no space. Default = On. * On 5 - 34 IMAGETEAM™ 3800E User’s Guide...
When Check Character is set to Validate and Transmit , the scanner will only read MSI bar codes printed with the specified type check character, and will transmit this character at the end of the scanned data. IMAGETEAM™ 3800E User’s Guide 5 - 35...
2-digit value and Save bar codes on the Programming Chart inside the back cover. Minimum and Maximum lengths = 4-48. 5 - 36 Validate Type 10 and Transmit Validate Type 11 and Transmit Max. length = 20 Max. length = 15 IMAGETEAM™ 3800E User’s Guide...
Page 87
Note: If you make an error while scanning the digits (before scanning Save), scan Discard on the back cover, scan the Minimum or Maximum bar code, scan the correct digits, and Save again. Minimum (Default =4) IMAGETEAM™ 3800E User’s Guide Maximum (Default =48) 5 - 37...
Discard on the back cover, scan the Minimum or Maximum bar code, scan the correct digits, and Save again. Minimum (Default =4) 5 - 38 Max. length = 20 Max. length = 15 Maximum (Default =48) IMAGETEAM™ 3800E User’s Guide * Off...
RSS-14 < Default All RSS-14 Settings > RSS-14 Reduced Space Symbology (RSS) is a family of linear bar codes that meets restricted space requirements, while still providing full product identification. * Off IMAGETEAM™ 3800E User’s Guide 5 - 39...
Note: If you make an error while scanning the digits (before scanning Save), scan Discard on the back cover, scan the Minimum or Maximum bar code, scan the correct digits, and Save again. Minimum (Default =4) IMAGETEAM™ 3800E User’s Guide Max. length = 20 Max. length = 15 Maximum (Default =74)
Discard on the back cover, scan the Minimum or Maximum bar code, scan the correct digits, and Save again. Minimum (Default =4) 5 - 42 Max. length = 20 Max. length = 15 Maximum (Default =80) IMAGETEAM™ 3800E User’s Guide * Off...
2-digit value and Save bar codes on the Programming Chart inside the back cover. Minimum and Maximum lengths = 1-2750. IMAGETEAM™ 3800E User’s Guide Max. length = 20 Max. length = 15...
When on, the “\” is used as an escape character and natural occurrences of “\” in data are replaced by “\\”. Default = Off . 5 - 44 Maximum (Default =2750) * Off IMAGETEAM™ 3800E User’s Guide...
When you turn on the PDF Learn Mode, the IT3800E’s light becomes very bright when you are at the best distance for reading the PDF417 code. Default = Off. IMAGETEAM™ 3800E User’s Guide * Off * Off...
Visual Menu settings. Installing Visual Menu from the Web 1. Use the following link to access the Developer’s Area of the Hand Held Prod- ucts web site: http://www.handheld.com/Site.aspx/na/en/developers/ download_software/?product=21 IMAGETEAM™ 3800E User’s Guide Visual Menu 6 - 1...
Page 98
7. To start Visual Menu, from the Start Menu click on Programs, Visual Menu, Visual Menu. Note: If you wish, you can create a shortcut to the Visual Menu executable on your desktop. 6 - 2 IMAGETEAM™ 3800E User’s Guide...
Keyboard Function Relationships The following Keyboard Function Code, Hex/ASCII Value, and Full ASCII “CTRL”+ relationships apply to all terminals that can be used with the scanner. Function Code HEX/ASCII Value IMAGETEAM™ 3800E User’s Guide Full ASCII “CTRL” + 7 - 1...
Page 100
The following chart indicates the equivalents of these five characters for different countries. Country United States Belgium Scandinavia France Germany Italy Switzerland United Kingdom Denmark Norway Spain 7 - 2 Codes < < Ã < ‘ IMAGETEAM™ 3800E User’s Guide...
Reserved Delete CR/Enter Insert Escape Home Print Back Space Back Tab * IBM 3191/92, 3471/72, 3196/97, 3476/77, Telex (all models) IMAGETEAM™ 3800E User’s Guide IBM XTs and IBM, DDC, Memorex Compatibles Telex, Harris* Reserved Reserved CR/Enter Enter Caps Lock Reserved...
Page 102
Reserved Enter New Line Tab/Field Forward Delete Field Exit Insert Clear Error Reset Home Print Back Space Back Tab IMAGETEAM™ 3800E User’s Guide Memorex Telex (88)** Reserved Enter PF10 PF11 PF12 Reserved Reserved New Line Field Forward Field Forward Reserved...
Page 103
Supported Interface Keys Supported Interface Keys IMAGETEAM™ 3800E User’s Guide Esprit 200, 400 Esprit 200, 400 ANSI ASCII Reserved Reserved New Line New Line New Line New Line New Line New Line Escape Escape Insert Insert Back Space Back Space...
Page 104
Apple Mac Interface Keys (not iMac) Reserved Enter/Numpad Enter CAPS ALT make ALT break CNTRL make CNTRL break RETURN APPLE make APPLE break RETURN Ins Help Home Prnt Scrn BACKSPACE LSHIFT TAB BACKSPACE 7 - 6 IMAGETEAM™ 3800E User’s Guide...
Show Software Revision Scan the bar code below to output the current software revision. Show Revision Show Data Format Scan the bar code below to show current data format settings. Data Format Settings IMAGETEAM™ 3800E User’s Guide 8 - 1...
When the On code is scanned, the first pass read rate and voting threshold are increased. Default = Off. * Off Note: If you want to further limit specular effects, reduce the scan speed using "Scan Rate" on page 2-1. 8 - 2 IMAGETEAM™ 3800E User’s Guide...
Keyboard Country Keyboard Style Keyboard Modifiers Communication (RS-232) Selections Baud Rate Word Length Data Bits Word Length Stop Bits Parity IMAGETEAM™ 3800E User’s Guide Factory Default Settings Default Setting Regular Control+ASCII Off Turbo Off Numeric Keypad Off Auto Direct Connect Off...
RTS/CTS off XON/XOFF off ACK/NAK off 25 inches/second Black High High 270 scans/second High Normal Voting Normal Don’t Reduce Short No Delay Automatic 0 (infinite) None CR LF Enable On/None IMAGETEAM™ 3800E User’s Guide Page 1-13 1-13 1-13 1-14 1-14 1-15...
Interleaved 2 of 5 Check Digit Message Length Strict Decoding Code 93 Selections Code 93 Message Length IMAGETEAM™ 3800E User’s Guide Default Setting Don’t Transmit No Check Character Min 4, Max 60 Don’t Transmit No Check Character Min 0, Max 48...
Default Setting Min 4, Max 48 Min 4, Max 48 Min 4, Max 80 Min 4, Max 80 Min 0, Max 80 AIM Telepen Min 1, Max 60 IMAGETEAM™ 3800E User’s Guide Page 5-12 5-13 5-13 5-14 5-14 5-15 5-15...
Message Length 9 - 6 Default Setting Validate Type 10, but Don’t Transmit Min 4, Max 48 Min 4, Max 48 Min 4, Max 74 Min 4, Max 80 IMAGETEAM™ 3800E User’s Guide Page 5-32 5-32 5-33 5-33 5-33 5-34 5-35...
A period (.) performs the command’s operation on the device’s non-volatile menu configuration table. Use the non-volatile table only for semi-permanent changes you want saved through a power cycle. (The non-volatile table allows only a limited number of writes.) IMAGETEAM™ 3800E User’s Guide 10 - 1...
NAK Indicates the command was good, but the Data field entry was out of the allowable range for this Tag and SubTag combination, e.g., an entry for a minimum message length of 100 when the field will only accept 2 characters. 10 - 2 IMAGETEAM™ 3800E User’s Guide...
Page 117
Check Character (CK2) is set to 0, or Not Required; concatenation (CCT) is set to 1, or Enabled; the Minimum Message Length (MIN) is 2 characters; the Maximum Message Length (MAX) is 60 characters; and the Default setting (DFT) has no value. IMAGETEAM™ 3800E User’s Guide 10 - 3...
Page 118
The scanner scans until a bar code has been read, until the deactivate com- mand is sent, or until the serial time out has been reached (see "Serial Trigger Time Out" on page 2-5 for a description, and the serial command on page 10- 10 - 4 IMAGETEAM™ 3800E User’s Guide...
Page 119
Factory Default Settings Terminal Interfaces Terminal ID Program Keyboard Country Keyboard Style Keyboard Modifiers Serial Port Connection Baud Rate IMAGETEAM™ 3800E User’s Guide Setting * Indicates default setting Default *Regular Caps Lock Shift Lock Automatic Caps Lock *Control + ASCII Off...
Page 120
*XON/XOFF Off XON/XOFF On *ACK/NAK Off ACK/NAK On Same Code Format *Code 39 Format *Black High White High Idle Low *Idle High IMAGETEAM™ 3800E User’s Guide Serial Command # Indicates a numeric entry 232WRD3 232WRD0 232WRD6 232WRD12 232WRD9 232WRD4 232WRD1...
Page 121
Reduce Quiet Zone Reread Delay Good Read Delay Trigger Mode Trigger Time Out Prefix/Suffix Selections Add CR Suffix to All Symbologies Prefix Suffix IMAGETEAM™ 3800E User’s Guide Setting * Indicates default setting 67 s/s 135 s/s *270 s/s Medium *High *Normal Beep...
Page 122
All Symbologies On Default All Codabar Settings *Don’t Transmit Transmit *No Check Char. Validate Modulo 16, But Don’t Transmit Validate Modulo 16, and Transmit IMAGETEAM™ 3800E User’s Guide Serial Command # Indicates a numeric entry RMVFNC0 RMVFNC1 DLYCHR## DLYCRX## DLY_XX## DLYFNC## DLYMSG##...
Page 123
Interleaved 2 of 5 Interleaved 2 of 5 Interleaved 2 of 5 Check Digit Interleaved 2 of 5 Message Length Interleaved 2 of 5 Strict Decoding IMAGETEAM™ 3800E User’s Guide Setting * Indicates default setting Require Minimum Maximum Default All Code 39 Settings *Don’t Transmit...
Page 124
Settings Minimum Maximum Default All Code 11 Settings 1 Check Digit *2 Check Digits Minimum Maximum Default All Code 128 Settings IMAGETEAM™ 3800E User’s Guide Serial Command # Indicates a numeric entry C93DFT C93ENA0 C93ENA1 C93MIN## C93MAX## R25DFT R25ENA0 R25ENA1...
Page 125
UPC A 5 Digit Addenda UPC A Addenda Required UPC A Addenda Separator UPC Strict Decoding UPC E UPC E0 UPC E1 IMAGETEAM™ 3800E User’s Guide Setting * Indicates default setting *Off Minimum Maximum Default All Telepen Settings *AIM Telepen Output...
Page 126
*Off *Off *Off *Off Default All EAN/ JAN 13 Settings *Off *Off *Off *Off Default All EAN/ JAN 8 Settings IMAGETEAM™ 3800E User’s Guide Serial Command # Indicates a numeric entry UPEEXP0 UPEEXP1 UPECKX0 UPECKX1 UPENSX0 UPENSX1 UPEAD20 UPEAD21 UPEAD50...
Page 128
Maximum Default All China Postal Code Settings *Off Minimum Maximum Default All PDF417 Settings Minimum Maximum *Off *Off *Off IMAGETEAM™ 3800E User’s Guide Serial Command # Indicates a numeric entry RSEDFT RSEENA0 RSEENA1 RSEMIN## RSEMAX## CPCDFT CPCENA0 CPCENA1 CPCMIN## CPCMAX##...
Page 129
Power Supply Noise Rejection Triggering Temperature Ranges: Operating Storage Humidity MTBF IMAGETEAM™ 3800E User’s Guide Specification 1.0 inches (2.5 cm) 3.5 inches (8.9 cm) 2.3 + .5 ounces ( 64.4 + 14 g) 2.5 inches ( 6.35 cm) 630 nm visible red LED Programmable to 270 scans per second ±30 degrees...
You need to program a suffix. Programming a suffix enables the scanner to output the bar code data plus the key you need (such as “CR”) to enter the data into your application. Refer to "Prefix/Suffix Overview" on page 3-1 for further information. IMAGETEAM™ 3800E User’s Guide 12 - 1...
Page 134
If you aren’t sure what programming options have been set in the scanner, or if you want the factory default settings restored, scan page 9-1. 12 - 2 Chapter "All Symbologies "Factory Default Settings" on IMAGETEAM™ 3800E User’s Guide "Terminal Chapter...
Hand Held Products provides service for all its products through service centers throughout the world. To obtain warranty or non-warranty service, return the unit to Hand Held Products (postage paid) with a copy of the dated purchase record attached. Contact the appropriate location below to obtain a Return Material Authorization number (RMA #) before returning the product.
You can also access product service and repair assistance online at www.handheld.com. Technical Assistance If you need assistance installing or troubleshooting your scanner, please call your Distributor or the nearest Hand Held Products technical support office: North America/Canada: Telephone: (800) 782-4263, option 4 (8 a.m. to 6 p.m. EST)
(C) static electricity or electro-static discharge, (D) operation under conditions beyond the specified operating parameters, or (E) repair or service of the product by anyone other than Hand Held Products or its authorized representatives. This warranty shall extend from the time of shipment for the duration published by Hand Held Products for the product at the time of purchase ("Warranty...
Page 138
Hand Held Products, Inc. extends these warranties only to the first end- users of the products. These warranties are nontransferable. The limited duration of the warranty for the 3800E is for two (2) years. 13 - 4 IMAGETEAM™ 3800E User’s Guide...