Table of Contents
Advertisement
Quick Links
THOMAS APICULTURE
French designer and manufacturer
Of beekeeping equipment
ZA de l'Évangile
321, rue Bernard de la Rochefoucauld
45450 Fay-aux-Loges – France
Tél: +33 (0)2 38 46 88 00
Fax : +33 (0)2 38 59 28 28
E-mail : contact@thomas-apiculture.com
www.thomas-apiculture.com
Adapt'matic
Lid and cross bar
Refs. 750/8025/8026/8028
Non-contractual pictures
USER'S
GUIDE
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Thomas Adaptmatic
Summary of Contents for Thomas Adaptmatic
- Page 1 THOMAS APICULTURE French designer and manufacturer Of beekeeping equipment ZA de l’Évangile 321, rue Bernard de la Rochefoucauld 45450 Fay-aux-Loges – France Tél: +33 (0)2 38 46 88 00 Fax : +33 (0)2 38 59 28 28 E-mail : contact@thomas-apiculture.com www.thomas-apiculture.com...
- Page 2 The motor is also available in 140 W (Ref.751) and can then be adapted to extraction cages with 20 mm axles (24 1/2 Dadant frames and more). The Adapt’matic lid and cross bar are designed for THOMAS extractors. The Adapt’matic lid and cross bar have two rotation directions and a speed variator that can go up to 280 rounds/min.
- Page 3 Adapt’matic cross bar and lid: User’s Guide ASSEMBLY Adapt’matic lid assembly Adapt’matic lid To replace a manual lid by an electric one, different models must be used. - Ref. 8025: for Duomel extractors - Ref. 8026: for Ø 530 mm extractors - Ref.
- Page 4 Adapt’matic cross bar and lid: User’s Guide Remove the lid and place the new one. Place the motor axis (1) and the pin (2), turn the cage until the two elements engage Replace and tighten the (A) and (B) bolts. - Version du 18/06/2020 -...
- Page 5 Adapt’matic cross bar and lid: User’s Guide Adapt’matic cross bar setup Unscrew the manual cross bar by taking off the (B) bolts. Measure the distance between the two sides (3). Measure the same distance on the cross bar and put marks in the centre of it. On each side of the motor, on the mark, drill a 10.5 mm hole and deburr with a larger bit - Version du 18/06/2020 -...
- Page 6 Adapt’matic cross bar and lid: User’s Guide The cross bar is 800 mm long; if needed, the ends can be cut off with a metal saw. In this case, cut the same length on each side. Take out the manual cross bar with two 17-size wrenches. Place the motor axis (1) and the pin (2), turn the cage until the two elements engage.
- Page 7 Adapt’matic cross bar and lid: User’s Guide Frequent questions CAUTION : Unplug the machine before any work is carried out. Problems Possible solutions - Check that the unit is connected to the electrical supply. - Check the power supply (power failure). - Check that the controller (7) is not set to 0.
- Page 8 (Monday - Saturday 8:00 am – 8:00 pm) Off season 8H/24 et 5 days /7 (Monday – Friday from 8:00 to 12:00 And from 1:30 pm to 6:00 pm) assistance-technique@thomas-apiculture.com Customer Service : 02 38 46 88 00 From 8:00 am to 12:00 am...
Need help?
Do you have a question about the Adaptmatic and is the answer not in the manual?
Questions and answers