17. Do not operate washer unless all enclosure panels are properly in place. 18. Do not tamper with controls. 19. To reduce risk of injury do not allow children to play in or on the washer 20. The washer must be connected to a proper electrical outlet with the correct...
2 weeks. This could be explosive and can explode under certain circumstances. If this is the case, before using the washer turn on all the hot faucets and let the hot water run for a few minutes. This will let the trapped hydrogen escape.
Parts and Features Operations Normal Operating Sounds Lint Filter Care and Cleaning Guide Cleaning and Maintenance Moving and Vacationing Storage of Your Washer Troubleshooting INSTALLATION INSTRUCTIONS Tools and Materials Required Unpacking Your Washer Levelling Yo ur Washer Steps for Installation...
OPERATING INSTRUCTIONS Parts and Features Control Panel Pre-wash Normal Hand Wash Heavy Duty Wash Quick wash Rinse Whites Delicate/ Casual Colors Wrinkle Control Spin Wash Extra Cycles Function Rinse Speed 8. Bleach injection inlet 15. Pulsator 1. Top lid 9. Front door 2.
Water level indicator will shut off if only Spin is selected. Extra Rinse Once a program is selected, press this button to have 2nd rinse. The washer will add a 2nd rinse. Wash Speed/Spin Speed For selecting the speed of washing or spinning .
Page 7
Push the Power On/Off button to switch the machine on or off. Start/Pause Once washer is powered and selections are chosen, push this button once to start the wash. While unit is working, push this button once to pause it.
Page 8
They can easily slide into the tub and may damage the tub. Pre-treat all stains and heavily soiled areas for best results. Do not overload your washer . When loading wet items, keep water level high enough so items can float easily in the water.
Note: Use only liquid bleach in dispenser. Warning: Be careful not to spill undiluted bleach on the washer cabinet or on your clothes. As it is a strong chemical, it may damage some of your clothes or the finish of the washer if not properly diluted.
Lint Filter The lint filter must be used during washing. It must be cleaned after each wash. 1.Take off the lint filter. 2.Clean out the lint in the filter. 3.Install the lint filter. Install the inner cover 1.Open the top lid of the washing machine. 2.Put the inner cover component on the outer tub cover, lining up the inner cover shaft to the installation hole of the corresponding outer tub cover shaft groove.
Cleaning and Maintenance Use only damp or sudsy cloth for cleaning control panel. To avoid any kind of damage to cabinet finish, wipe washer cabinet as needed. If you spill liquid/powdered softener bleach or detergent on the cabinet, wipe cabinet immediately because it can damage the finish.
Disconnect the electrical plug Dry the inner wash tub. If you are moving the washer, disconnect the drain hose. Turn the levelling legs clockwise all the way in. Move and store your washer in an upright position only To prevent mould or mildew, leave the lid open so moisture inside the machine can evaporate.
Check if the circuit breaker needs to be reset or if the fuse needs to be replaced. Check if the washer is overloaded: the load may need to be re-balanced and clothes may need to be redistributed. Check if the lid is open. You may have to close the lid properly The washer pauses in some cycles.
Page 14
Washer is making noise: Washer may need to be reinstalled. (Check washer installation section) Washer load may need to be re-balanced, as the load may be uneven. Coins, loose change, buttons or other heavy objects could make noise(read Operating Guide-Normal Operating Sounds).
INSTALLATION INSTRUCTIONS Tools and Materials Required You will need to have the following tools to help you in the installation of your washer: Pliers Wrench Tape Measure Gloves Level Accessories Supplied 1.Hot & Cold inlet hoses 2.Drain Hose Hook 3.Pipe Hoop 4.Inner Tub Cover...
Leveling Your Washer Your washer has 4 leveling legs; which are located on the bottom corners. After properly placing your washer in its final position, you canlevel your washer. Leveling legs can be adjusted by turning them counter clockwise to raise your washer or turning them clockwise to lower your washer.
Steps for Installation Select a away suitable location for the washer on a hard even surface from direct sunlight or heat source e.g. radiators, base board heaters, cooking appliances etc.Any floor unevenness should be corrected with the leveling legs located on the bottom corners of the washer.The washer must be placed at room temperature.You must not place washer...
Page 18
Caution:If, after completing these steps, you are unsure that unit is properly installed, contact a qualified installer.To ensure that your washer is properly installed, it is recommended that it be installed by a certified installer.
Occasionally there may be power interruptions due to thunderstorms or other causes. Remove the power cord from AC outlet when a power outage occurs. When power has been restored re-plug power cord to AC outlet. If outage is for a prolonged period, clean washer before using it again.