Related Manuals for Genie PWIPNW4B
Summary of Contents for Genie PWIPNW4B
- Page 1 4MP H.265 IP IR Bullet Camera with 2.8mm Lens and Wi-Fi PWIPNW4B User Manual Please read these instructions carefully before operating the unit and keep for further reference.
- Page 2 Notes on Safety This product is intended to be supplied by a Listed Power Unit, marked with 'Limited Power Source', 'LPS' on unit, output rated minimum 12V/2 A or POE 48V/ 350mA(depending on models), no more than 2000m altitude of operation and Tma=60 Deg.C.
- Page 3 Disclaimer With regard to the product with internet access, the use of product shall be wholly at your own risks. Our company shall be irresponsible for abnormal operation, privacy leakage or other damages resulting from cyber attack, hacker attack, virus inspection, or other internet security risks;...
- Page 4 against harmful interference. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. The user will be required to correct the interface at his own expense in case the harmful interference occurs.
-
Page 5: Table Of Contents
Table of Contents Introduction ........................1 Network Configuration ....................2 Wired Network Connection ................2 2.1.1 Access through IP-Tool ................2 2.1.2 Directly Access through IE ............... 4 2.1.3 WAN ......................5 Wi-Fi Connection ....................7 Live View ........................10 Network Camera Configuration ................. - Page 6 Network Camera User Manual 4.5.11 QoS ....................36 4.5.12 Wi-Fi ....................37 Security Configuration ..................37 4.6.1 User Configuration ................. 37 4.6.2 Online User ..................... 38 4.6.3 Block and Allow Lists ................39 4.6.4 Security Management ................39 Maintenance Configuration................39 4.7.1 Backup and Restore ................
-
Page 7: Introduction
Network Camera User Manual 1 Introduction This IP-CAMERA (short for IP-CAM) is designed for high performance CCTV solutions. It adopts state of the art video processing chips, integrated with the most advanced technologies (like video encoding and decoding technology) to make the image transmission more stable and smooth. -
Page 8: Network Configuration
Network Camera User Manual 2 Network Configuration You may connect IP-Cam via the wired network or wireless network. The details are as follows: 2.1 Wired Network Connection In LAN, there are two ways to access IP-Cam: 1. access through IP-Tool; 2. directly access through IE browser. - Page 9 Network Camera User Manual For example, the IP address of your computer is 192.168.1.4. So the IP address of the camera shall be changed to 192.168.1.X. After modification, please enter the password of the administrator and click the “Modify” button to modify the setting. ...
-
Page 10: Directly Access Through Ie
Network Camera User Manual The system will pop up the above-mentioned textbox to ask you to change the default password. It is strongly recommended to change the default password for account security. If “Do not show again” is checked, the textbox will not appear next time. 2.1.2 Directly Access through IE The default network settings are as shown below: IP address: 192.168.226.201... -
Page 11: Wan
Network Camera User Manual ② Open the IE browser and enter the default address of IP-CAM and confirm. ③ Follow directions to download and install the Active X control. ④ Enter the default username and password in the login window and then enter to view. 2.1.3 WAN ... - Page 12 Network Camera User Manual IP Setup ③ Go to the router’s management interface through IE browser to forward the IP address and port of the camera in the “Virtual Server”. Router Setup ④ Open the IE browser and enter its WAN IP and http port to access. (for example, if the http port is changed to 81, please enter “192.198.1.201:81”...
-
Page 13: Wi-Fi Connection
Network Camera User Manual ② Go to Config NetworkTCP/IPPPPoE Config menu. Enable PPPoE and then enter the user name and password from your internet service provider. ③ Go to Config NetworkDDNS menu. Before configuring the DDNS, please apply for a domain name first. - Page 14 Network Camera User Manual then find the IP address of the camera. The default IP address of this camera is 192.168.226.201. Modify the IP address and gateway of the camera and make sure its network address is in the same local network segment as the computer’s. Then double click it. This will bring you to the login interface of the camera.
- Page 15 Network Camera User Manual APP Monitoring ① Enable Wi-Fi function in your mobile phone. ② Open your phone’s APP store and search “Surperlive Plus”. ③ Install this APP in your phone. ④ Run this APP and then add the IP address, username and password of the IPC or scan the QRcode of the IPC (Go to ConfigSystemBasic Information interface through Web Client.
-
Page 16: Live View
Network Camera User Manual 3 Live View After logging in, the following window will be shown. The following table is the instructions of the icons on the live view interface. Icon Description Icon Description Original size Zoom out Fit correct scale Abnormal clarity indicator Auto (fill the window) Scene change indicator... -
Page 17: Network Camera Configuration
Network Camera User Manual 4 Network Camera Configuration In the Webcam client, choose “Config” to go to the configuration interface. Note: Wherever applicable, click the “Save” button to save the settings. 4.1 System Configuration 4.1.1 Basic Information In the “Basic Information” interface, the system information of the device is listed. Some versions may support device ID and QR code. -
Page 18: Local Config
Network Camera User Manual Select the time zone and DST as desired. Click the “Date and Time” tab to set the time mode. 4.1.3 Local Config Go to ConfigSystem Local Config to set up the storage path of captured pictures and recorded videos on the local PC. - Page 19 Network Camera User Manual Video Quota: Set the capacity proportion of record files on the SD card. Schedule Recording Settings 1. Go to ConfigSystemStorageRecord to go to the interface as shown below. 2. Set record stream, pre-record time and cycle writing. Pre Record Time: Set the time to record before the actual recording begins.
-
Page 20: Image Configuration
Network Camera User Manual “Erase”: Delete the schedule. Drag the mouse to erase the time on the timeline. Manual Input: Click it for a specific day to enter specific start and end times. This adds more granularities (minutes). Day schedule Set the alarm time for alarm a special day, such as a holiday. -
Page 21: Display Configuration
Network Camera User Manual 4.2.1 Display Configuration Go to ImageDisplay interface as shown below. The image’s brightness, contrast, hue and saturation and so on for common, day and night mode can be set up separately. The image effect can be quickly seen by switching the configuration file. Brightness: Set the brightness level of the camera’s image. -
Page 22: Video Configuration
Network Camera User Manual HLC: lowers the brightness of the entire image by suppressing the brightness of the image’s bright area and reducing the size of the halo area. BLC: If enabled, the auto exposure will activate according to the scene so that the object ... -
Page 23: Osd Configuration
Network Camera User Manual Three video streams can be adjustable. Resolution: The size of image. Frame rate: The higher the frame rate, the video is smoother. Bitrate type: CBR and VBR are optional. Bitrate is related to image quality. CBR means that no matter how much change is seen in the video scene, the compression bitrate will be kept constant. -
Page 24: Video Mask
Network Camera User Manual Set time stamp, device name and OSD content here. After enabling the corresponding display and entering the content, drag them to change their position. Then click the “Save” button to save the settings. 4.2.4 Video Mask Go to ImageVideo Mask interface as shown below. -
Page 25: Roi Configuration
Network Camera User Manual To clear the video mask: Click the “Clear” button to delete the current video mask area. 4.2.5 ROI Configuration Go to ImageROI Config interface as shown below. An area in the image can be set as a region of interest. -
Page 26: Alarm Configuration
Network Camera User Manual 4.3 Alarm Configuration 4.3.1 Motion Detection Go to AlarmMotion Detection to set motion detection alarm. 1. Check “Enable” check box to activate motion based alarms. If unchecked, the camera will not send out any signals to trigger motion-based recording to the NVR or CMS, even if there is motion in the video. -
Page 27: Other Alarm
Network Camera User Manual interface as shown below. Move the “Sensitivity” scroll bar to set the sensitivity. Higher sensitivity value means that motion will be triggered more easily. Select “Add” and click “Draw”. Drag the mouse to draw the motion detection area; Select “Erase”... -
Page 28: Alarm Server
Network Camera User Manual 3. Click “Enable” and set the alarm holding time. 4. Set alarm trigger options. Trigger Email and FTP. The setup steps are the same as motion detection. Please refer to motion detection chapter for details. 4.3.3 Alarm Server Go to AlarmAlarm Server interface as shown below. - Page 29 Network Camera User Manual 1. Enable object removal detection and then select the detection type. Enable Left Detection: Alarms will be triggered if there are items left in the pre-defined area. Enable Item Missing Detection: Alarms will be triggered if there are items missing in the pre-defined area.
-
Page 30: Exception
Network Camera User Manual the schedule recording (See Schedule Recording). ※ The configuration requirements of camera and surrounding areas 1. The range of the detection object should occupy from 1/50 to 1/3 of the entire image. 2. The detection time of objects in the camera shall be from 3 to 5 seconds. 3. -
Page 31: Line Crossing
Network Camera User Manual 4. Set the sensitivity of the exception detection. Click “Sensitivity” tab to go to the interface as shown below. Drag the slider to set the sensitivity value or directly enter the sensitivity value in the textbox. Click “Save”... -
Page 32: Intrusion
Network Camera User Manual Set the alarm line number and direction. Only one line can be added. Multiple lines cannot be added simultaneously. Direction：A<->B, A->B and A<-B optional. This indicates the direction of the intruder who crosses over the alarm line that would trigger the alarm. A<->B: The alarm will be triggered when the intruder crosses over the alarm line from B to A or from A to B. - Page 33 Network Camera User Manual Go to ConfigEventIntrusion interface as shown below. 1. Enable region intrusion detection alarm and set the alarm holding time. 2. Set alarm trigger options. The setup steps are the same as motion detection. Please refer to motion detection chapter for details.
-
Page 34: Network Configuration
Network Camera User Manual 4. Keep the mounting angle of the camera at about 45° . 5. The detected objects should not be less than 1% of the entire image and the largest sizes of the detected objects should not be more than 1/8 of the entire image. 6. -
Page 35: Port
Network Camera User Manual Click “IP Change Notification Config” to go to the interface as shown below. Trigger Email: when the IP address of the device is changed, the new IP address will be sent to the email address that has been set up. Trigger FTP: when the IP address of the device is changed, the new IP address will be sent to FTP server that has been set up. -
Page 36: Ddns
Network Camera User Manual 1. Check “Enable”. 2. Check the IP address and port of the transfer media server in the ECMS/NVMS. Then enable the auto report in the ECMS/NVMS when adding a new device. Next, enter the remaining information of the device in the ECMS/NVMS. After that, the system will automatically allot a device ID. -
Page 37: 802.1X
Network Camera User Manual Create domain name. After the domain name is successfully applied for, the domain name will be listed as below. 3. Enter the username, password, domain you apply for in the DDNS configuration interface. 4. Click the “Save” button to save the settings. 4.5.5 802.1x IEEE802.X is an access control protocol. -
Page 38: Rtsp
Network Camera User Manual ① The network camera initiates the authentication of 802.1x protocol via web client and then the authentication is received by the switch supporting 802.1x protocol. ② The switch provides the camera with a physical or logic local network interface and verifies the camera. -
Page 39: Upnp
Network Camera User Manual If “auto start” is enabled, the multicast received data should be added into a VLC player to play the video. If “Allow anonymous login…” is checked, there is no need to enter the username and password to view the video. -
Page 40: Ftp
Network Camera User Manual Sender Address: sender’s e-mail address. User name and password: sender’s user name and password. Server Address: The SMTP IP address or host name. Select the secure connection type at the “Secure Connection” pull-down list according to what’s required. -
Page 41: Https
Network Camera User Manual Server Name: The name of the FTP server. Server Address: The IP address or domain name of the FTP. Upload Path: The directory where files will be uploaded to. Port: The port of the FTP server. Use Name and Password: The username and password that are used to login to the FTP server. -
Page 42: Qos
Network Camera User Manual * If there is a signed certificate, click “Browse” to select it and then click “Install” to install it. * Click “Create a private certificate” to enter the following creation interface. Click the “Create” button to create a private certificate. Enter the country (only two letters available), domain (camera’s IP address/domain), validity date, password, province/state, region and so on. -
Page 43: Wi-Fi
Network Camera User Manual Video/Audio DSCP: The range is from 0 to 63. Alarm DSCP: The range is from 0 to 63. Manager DSCP: The range is from 0 to 63. Generally speaking, the larger the number is, the higher the priority is. 4.5.12 Wi-Fi Click ConfigNetworkWIFI to go to the Wi-Fi configuration interface. -
Page 44: Online User
Network Camera User Manual video. Advanced user has the same permissions as an Administrator except for; user, backup settings, factory reset, and upgrading the firmware. 5. Enter the MAC address of the PC in “Bind MAC” textbox. If this option is enabled, only the PC with the specified MAC address can access the camera for that user. -
Page 45: Block And Allow Lists
Network Camera User Manual 4.6.3 Block and Allow Lists Go to ConfigSecurityBlock and Allow Lists as shown below. The setup steps are as follows: Check the “Enable address filtering” check box. Select “Block/Allow the following address”, IPv4/IPv6/MAC and then enter IP address or MAC address in the address box and click the “Add”... -
Page 46: Reboot
Network Camera User Manual Import & Export Settings Configuration settings of the camera can be exported form a camera into another camera. 1. Click “Browse” to select the save path for import or export information on the PC. 2. Click the “Import Setting” or “Export Setting” button. Default Settings ... -
Page 47: Operation Log
Network Camera User Manual 1. Click the “Browse” button to select the save path of the upgrade file 2. Click the “Upgrade” button to start upgrading the firmware. 3. The device will restart automatically Caution! Do not close the browser or disconnect the camera from the network during the upgrade. -
Page 48: Search
Network Camera User Manual 5 Search 5.1 Image Search Click Search to go to the interface as shown below. Images that are saved on the SD card can be found here. Local Image Search Choose “Picture”—“Local”. Set time: Select date and choose the start and end time. Click to search the images. - Page 49 Network Camera User Manual Set time: Select date and choose the start and end time. Choose the alarm events at the bottom of the interface. Click to search the images. Double click a file name in the list to view the captured photos. Click to return to the previous interface.
-
Page 50: Video Search
Network Camera User Manual 5.2 Video Search Local Video Search Click Search to go to the interface as shown below. Videos were recorded locally to the PC can be played in this interface. Choose “Record”—“Local”. Set search time: Select the date and choose the start and end time. Click to search the images. - Page 51 Network Camera User Manual Icon Description Icon Description Play button. After pausing the video, click this button to Pause button continue playing. Stop button Speed down Speed up Watermark display Enable / disable audio; drag the slider to adjust the volume after enabling audio (only available for some models) .
- Page 52 Network Camera User Manual The time table can be shown in 24H/12H/2H/1H format by clicking the corresponding buttons. Video clip and downloading Search the video files according to the above mentioned steps. Select the start time by clicking on the time table. Click to set the start time and then this button turns blue ( Select the end time by clicking on the time table.
-
Page 53: Appendix
Network Camera User Manual Appendix Appendix 1 Q & A How to find the password? A：Reset the device to the default factory settings. Default IP: 192.168.226.201; User name: admin; Password: 123456 Fail to connect devices through IE browser. A: Network is not well connected. Check the connection and make sure it is connected well. B: IP address is not available. - Page 54 Network Camera User Manual Q：No sound can be heard. A：Audio input device is not connected. Please connect and try again. B: Audio function is not enabled at the corresponding channel. Please enable this function. Q：Wi-Fi cannot be connected. A: 1. Check whether Wi-Fi is enabled. 2.
- Page 55 Network Camera User Manual...
-
Page 56: Appendix 2 Specifications
Network Camera User Manual Appendix 2 Specifications Specification /Model IR Water-proof Bullet Network Camera Image Sensor 1/2.7＂CMOS Image Size 2592× 1944 Electronic Shutter 1/25s~1/100000s Iris Type Fixed Iris 0.011 lux@F1.2, AGC ON: 0 lux with IR Min. llumination 0.04 lux@F2.26, AGC ON: 0 lux with IR 2.8mm@F2.0, horizontal field of view: 110°... - Page 57 Network Camera User Manual Power Consumption < 5W Operating Temperature: -30° C~60° C; Relative humidity : less than 95% (non-condensing) Environment Dimension (mm) 167.6× 74.7× 148.2 Weight(net） Approx. 0.465KG Installation Wall mounting; ceiling mounting...
- Page 58 Sales +44(0)1707 330541 Enquiries sales@genieproducts.co.uk Website www.genieproducts.co.uk...
Need help?
Do you have a question about the PWIPNW4B and is the answer not in the manual?
Questions and answers