Figures - ABB XAC25354 Operation Manual

Operation Manual / A100-L

Figures

Figures
Fig. 1: Layout and function of the turbocharger ...... 6
Fig. 2: Locations of the rating plates ......................... 8
Fig. 3: Warning plate locations ................................... 13
Fig. 4: Rating plate ........................................................ 13
Fig. 5: Attachment of loads on the crane hook ....... 16
Fig. 6: Attachment angle.............................................. 16
Fig. 7: Fitting the lifting gear ..................................... 26
Fig. 8: Placing the turbocharger................................. 27
Fig. 9: Compressor-end foot...................................... 28
Fig. 10: Turbine-end foot ............................................ 28
Fig. 11: Oil temperature at the outlet ....................... 34
Fig. 12: Layout and overview of the speed measure-
ment system.................................................................. 36
Fig. 13: Replacing the speed sensor ......................... 38
Fig. 14: U-tube manometer at the filter silencer .... 39
Fig. 15: Noise insulation, bellows ............................... 41
Fig. 16: Layout and overview of filter silencer ........ 49
Fig. 17: Dismantling filter ring circumferential part ....
51
Fig. 18: Opening filter ring lock................................... 51
Fig. 19: Attaching new filter ring ............................... 52
Fig. 20: Fitting new filter ring .................................... 52
Fig. 21: Overview of wet cleaning of compressor .. 55
Fig. 22: Filter plug view................................................ 56
Fig. 23: Dry cleaning device ........................................ 58
Fig. 24: Drain pipe diagram ......................................... 61
Fig. 25: Weights of assemblies ................................. 70
Fig. 26: Dismantling the filter silencer casing ......... 71
Fig. 27: Fitting the filter silencer casing ................... 72
Fig. 28: Fitting the filter silencer casing .................. 73
Fig. 29: Fitting the filter silencer casing .................. 73
Fig. 30: Fitting the filter silencer casing .................. 74
Fig. 31: Fitting the filter silencer casing................... 74
Fig. 32: Fitting the bellows .......................................... 75
© Copyright 2021 ABB. All rights reserved.
Fig. 33: Dismantling the filter silencer....................... 76
Fig. 34: Dismantling the filter silencer ...................... 77
Fig. 35: Dismantling the filter silencer with noise
package ........................................................................... 78
Fig. 36: Dismantling the wall insert............................ 79
Fig. 37: Moving out wall insert .................................... 80
Fig. 38: Putting down wall insert ................................ 80
Fig. 39: Putting down wall insert ................................ 81
Fig. 40: Dismantling the diffuser ............................... 82
Fig. 41: Measuring axial clearance A........................... 83
Fig. 42: Removing the insulation (A175-L and smal-
ler)..................................................................................... 84
Fig. 43: Dismantling the gas inlet casing (A175-L and
smaller) ............................................................................ 85
Fig. 44: Dismantling the nozzle ring (A175-L and
smaller) ............................................................................ 86
Fig. 45: Dismantling the gas inlet casing (180-L and
larger)............................................................................... 87
Fig. 46: Fitting the nozzle ring holder........................ 88
Fig. 47: Dismantling the nozzle ring........................... 89
Fig. 48: Put down the nozzle ring ............................... 89
Fig. 49: Fitting the nozzle ring (A175-L and smaller) ...
90
Fig. 50: Fitting the gas outlet casing (A175-L and
smaller) ............................................................................ 91
Fig. 51: Fitting the insulation (A175-L and smaller). 92
Fig. 52: Looping around the nozzle ring (A180-L and
larger)............................................................................... 93
Fig. 53: Fitting the nozzle ring (A180-L and larger). 94
Fig. 54: Fitting the gas inlet casing (A180-L and lar-
ger) ................................................................................... 95
Fig. 55: Measuring axial clearance A .......................... 96
Fig. 56: Fitting the diffuser.......................................... 97
Fig. 57: Positioning wall insert .................................... 98
Fig. 58: Fitting wall insert ........................................... 99
Fig. 59: Fitting the filter silencer .............................. 101
Fig. 60: Fitting the filter silencer .............................. 102
HZTL4034_EN Revision T December 2021