Table of Contents
Advertisement
Viewfinder Advanced Menu
Advanced menu page 3
P A G E 3 ( N E X T m$ P R E V m4)
mA W B M E M : 2
T O N E : O F F
B A R S : S M P T E
a)
R E M O T E 1 : R E C
R E M O T E 2 : M A R K
B A U D R A T E : 3 8 4 0 0
E X I T M E N U ( Y E S m4)
a) For DXC-D30P: EBU75
Item
Settings
AWB MEM
2 (normal value): No
Selects whether or not to
correspondence with FILTER
make the FILTER knob
knob settings. Only two
settings (1 to 4) correspond
adjustment values (A and B)
to separate white balance
are stored in memory.
2 × 4FL: Correspondence
adjustment values stored in
memory.
with FILTER knob settings.
Each of the four knob
settings can be used to set A
and B adjustment values, for
a total of eight settings.
TONE
ON (normal value): Output
Selects whether or not to
audio signal.
output a 1-kHz audio signal
OFF: Do not output audio
with the color bars when the
signal.
OUTPUT/DL/DCC+ has
been set to BARS.
BARS
SMPTE (normal value for
Selects normal width or
DXC-D30): Normal width
narrower width for color
EBU75 (normal valve for
bars.
DXC-D30P): EBU 75%
EBU100 (for DXC-D30P):
EBU 100%
SPLIT (for DXC-D30P): Not
for normal operation
SNG: Narrower than normal
(used for satellite
communications, etc.)
REMOTE1
REC (normal value):
Sets a function for position 1
Specifies recording start/stop
of a switch connected to the
MARK: Specifies a Mark IN/
REMOTE1 connector.
a)
OUT point.
CUE: Specifies a cue point.
NG: Specifies NG/OK.
REMOTE2
REC: Specifies recording
Sets a function for position 2
start/stop.
of a switch connected to the
MARK (normal value):
REMOTE1 connector.
a)
Specifies a Mark IN/OUT
point.
CUE: Specifies a cue point
NG: Specifies NG/OK.
BAUD RATE
9600, 38400 (normal value)
Sets a baud rate for a
computer connected to the
REMOTE connector 1 (to be
supported in future version).
a) For more information about a connectable switch,
contact your Sony dealer.
58
Chapter 4 Viewfinder Screen Indications and Menus
Advanced menu page 4
P A G E 4 ( N E X Tm$ P R E V m4)
M A R K E R : C E N T / 9 0 %
mZ E B R A : 1
Z E B R A 1 : 7 0 I R E
a)
V F S D T L :± 0
×
V F T A L L Y : 2
E X I T M E N U ( Y E Sm4)
a) For DXC-D30P: 70%
Settings
Item
MARKER
CENT/90% (normal value):
Selects ON/OFF setting for
Displays center marker and
center marker, size setting
safety zone marker at 90%
(percentage of viewfinder
size.
screen area), and display
CENT/80%: Displays center
ON/OFF setting.
marker and safety zone
marker at 80% size.
90%: Displays only safety
zone marker at 90% size.
80%: Displays only safety
zone marker at 80% size.
CENT: Displays only center
marker.
ZEBRA
1 (normal value): Displays
Selects type of zebra pattern
the zebra pattern over parts
display.
having a video level.
between 70 and 90 IRE (or
70 and 90%).
Use the next item (ZEBRA1)
to select the base level.
2: Displays the zebra pattern
over parts having video
levels of 100 IRE or above
( or 100% or above).
1/2: Dual display (both 1
and 2)
ZEBRA1
70 IRE (normal value) to 90
Sets base level for zebra
IRE or 70% (normal value)
pattern 1.
to 90%
Can be set for each IRE
step or 1% step.
VF S DTL
–99 to +0 (normal value) to
Sets the detail level of
+99
images on the viewfinder
Negative values set softer
screen (displayed only when
edges and positive values
the DXF-501/501CE/601/
set sharper edges.
601CE viewfinder is
attached).
×1: Uses only the upper
VF TALLY
Selects whether or not to use
REC/TALLY indicator.
×2 (normal value): Uses
more than one REC/TALLY
indicators in the viewfinder
two REC/TALLY indicators.
(displayed only when the
DXF-701/701CE viewfinder
is attached).
Advanced menu page 5
P A G E 5 ( N E X T m$ P R E V m4)
mS S I N D : A L W A Y S
L L I N D : O N
M I C I N D : O N
I R I S I N D : O N
G A I N I N D : O N
F I L T E R I N D : O N
E X I T M E N U ( Y E S m4)
Item
Settings
SS IND
3SEC: Displays shutter
Selects the mode for
setting for three seconds only
showing the shutter setting
when the setting has been
when displaying the normal
changed.
indications.
ALWAYS (normal value):
Displays the shutter setting at
all times.
LL IND
ON (normal value):
Selects whether or not to
Displays.
show the LOW LIGHT
OFF: Not display.
indication on the normal
indications when inadequate
lighting is detected.
MIC IND
ON (normal value):
Selects whether or not to
Displays.
show the camera
OFF: Not display.
microphone output
indication on the normal
indications.
IRIS IND
ON (normal value):
Selects whether or not to
Displays.
show the lens's F-stop value
OFF: Not display.
(iris indication) on the
normal indications. The F-
stop value is always
displayed when in EZ mode.
GAIN IND
ON (normal value): Always
Selects whether or not to
displays.
always show the gain
OFF: displays for two
setting indication on the
seconds only when the
normal indications.
setting has been changed.
FILTER IND
ON (normal value): Always
Selects whether or not to
displays.
always show the FILTER
OFF: Displays for two
knob setting indication on
seconds only when the
the normal indications.
setting has been changed.
The FILTER knob setting
indicator is always displayed
when in EZ mode.
Advanced menu page 6
P A G E 6 ( N E X Tm$ P R E V m4)
mA U D I O I N D : O N
T A P E I N D : O N
T C I N D : O N
I D I N D : O F F
I D S E T :µ
(
)
E X I T M E N U ( Y E Sm4)
Item
Settings
AUDIO IND
ON (normal value):
Selects whether or not to
Displays.
show the audio level
OFF: Not display.
indication on the normal
indications (valid only when
the DSR-1/1P or PVV-3/3P
is connected).
TAPE IND
ON (normal value):
Selects whether or not to
Displays.
show the VTR's remaining
OFF: Not display.
tape indication on the normal
indications. (valid only when
the DSR-1/1P or PVV-3/3P
is connected).
TC IND
ON (normal value):
Selects whether or not to
Displays.
show the time data indication
OFF: Not display.
on the normal indications
(valid only when the DSR-1/
1P or PVV-3/3P is
connected).
ID IND
ON (normal value):
Selects whether or not to
Displays.
display the camera ID when
OFF: Not display.
displaying color bars.
ID SET
See "To set the camera ID"
Sets the camera ID (up to
on next page.
eight characters, including
alphanumerics, symbols,
and spaces).
59
Chapter 4 Viewfinder Screen Indications and Menus
Advertisement
Table of Contents
