Table of Contents
Advertisement
Available languages
Available languages
Quick Links
MODELS 7802R AND 7802R–EU HEAVY–DUTY
Models 7802R and 7802R–EU Reversible Drills are designed for drilling, honing,
reaming and hole sawing.
Ingersoll–Rand is not responsible for customer modification of tools for applications
on which Ingersoll–Rand was not consulted.
IMPORTANT SAFETY INFORMATION ENCLOSED.
READ THIS MANUAL BEFORE OPERATING TOOL.
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THE INFORMATION
IN THIS MANUAL INTO THE HANDS OF THE OPERATOR.
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
PLACING TOOL IN SERVICE
•
Always operate, inspect and maintain this tool in
accordance with all regulations (local, state,
federal and country), that may apply to hand
held/hand operated pneumatic tools.
•
For safety, top performance, and maximum
durability of parts, operate this tool at 90 psig
(6.2 bar/620 kPa) maximum air pressure at the
inlet with 3/8" (10 mm) inside diameter air supply
hose.
•
Always turn off the air supply and disconnect the
air supply hose before installing, removing or
adjusting any accessory on this tool, or before
performing any maintenance on this tool.
•
Do not use damaged, frayed or deteriorated air
hoses and fittings.
•
Be sure all hoses and fittings are the correct size
and are tightly secured. See Dwg. TPD905–1 for a
typical piping arrangement.
•
Always use clean, dry air at 90 psig (6.2 bar/
620 kPa) maximum air pressure. Dust, corrosive
fumes and/or excessive moisture can ruin the
motor of an air tool.
•
Do not lubricate tools with flammable or volatile
liquids such as kerosene, diesel or jet fuel.
•
Do not remove any labels. Replace any damaged
label.
USING THE TOOL
•
Always wear eye protection when operating or
performing maintenance on this tool.
The use of other than genuine Ingersoll–Rand replacement parts may result in safety hazards, decreased tool
performance, and increased maintenance, and may invalidate all warranties.
Repairs should be made only by authorized trained personnel. Consult your nearest Ingersoll–Rand Authorized
Servicenter.
Refer All Communications to the Nearest
Ingersoll–Rand Office or Distributor.
Ingersoll–Rand Company 2000
Printed in U.S.A.
INSTRUCTIONS FOR
REVERSIBLE AIR DRILLS
TPD1447
•
•
•
•
•
•
•
•
•
•
03534468
Always wear hearing protection when operating
this tool.
Keep hands, loose clothing and long hair away
from rotating end of tool.
Note the position of the reversing lever before
operating the tool so as to be aware of the direction
of rotation when operating the throttle.
Anticipate and be alert for sudden changes in
motion during start up and operation of any power
tool.
Keep body stance balanced and firm. Do not
overreach when operating this tool. High reaction
torques can occur at or below the recommended
air pressure.
Tool accessory may continue to rotate briefly after
throttle is released.
Air powered tools can vibrate in use. Vibration,
repetitive motions or uncomfortable positions may
be harmful to your hands and arms. Stop using
any tool if discomfort, tingling feeling or pain
occurs. Seek medical advice before resuming use.
Use accessories recommended by Ingersoll–Rand.
This tool is not designed for working in explosive
atmospheres.
This tool is not insulated against electric shock.
Form P6775
GB
Edition 7
April, 2000
Advertisement
Table of Contents
Related Manuals for Ingersoll-Rand 7802R
Summary of Contents for Ingersoll-Rand 7802R
- Page 1 MODELS 7802R AND 7802R–EU HEAVY–DUTY REVERSIBLE AIR DRILLS TPD1447 Models 7802R and 7802R–EU Reversible Drills are designed for drilling, honing, reaming and hole sawing. Ingersoll–Rand is not responsible for customer modification of tools for applications on which Ingersoll–Rand was not consulted.
-
Page 2: Warning Label Identification
Type of Handle Free Speed Chuck Capacity dB (A) Level •Power in (mm) Pressure 7802R, 7802R–EU pistol 2,000 3/8 (10) 92.8 105.8 Tested in accordance with ANSI S5.1–1971 at free speed ♦ Tested in accordance to ISO8662–1 at 80% rated free speed •... -
Page 3: Declaration Of Conformity
Ingersoll–Rand, Co. (supplier’s name) Swan Lane, Hindley Green, Wigan WN2 4EZ (address) declare under our sole responsibility that the product, Model 7802R–EU Reversible Air Drill to which this declaration relates, is in compliance with the provisions of 98/37/EC Directives. EN292 ISO8662 By using the following Principle Standards: (1994 →... -
Page 4: Utilisation De L'outil
PERFORMANCE MODÈLES 7802R ET 7802R–EU TPD1447 NOTE Les perçeuses réversibles Modèles 7802R et 7802R–EU sont destinées aux opérations de perçage, de rodage, d’alésage et de sciage de trou. Ingersoll–Rand ne peut être tenu responsable de la modification des outils par le client pour les adapter à... -
Page 5: Mise En Service De L'outil
Vitesse à vide Capacité du mandrin dB (A) vibration •Puissance tr/mn pouces (mm) Pression 7802R, 7802R–EU pistolet 2.000 3/8 (10) 92,8 105,8 Testé conformément à ANSI S5.1–1971 en vitesse libre ♦ Testé conformément à ISO8662–1 a 80% vitesse libre nominale •... -
Page 6: Certificat De Conformité
(nom du fournisseur Swan Lane, Hindley Green, Wigan WN2 4EZ (adresse déclarons sous notre seule responsabilité que le produit: Perçeuse Pneumatique Réversible Modèle 7802R–EU objet de ce certificat, est conforme aux prescriptions des Directives: 98/37/CE EN292 ISO8662 en observant les normes de principe suivantes: (1994 →... - Page 7 UMSTEUERBARE HOCHLEISTUNGS–BOHRMASCHINEN DER BAUREIHE 7802R UND 7802R–EU TPD1447 HINWEIS Umsteuerbare Bohrmaschinen der Baureihe 7802R und 7802R–EU werden eingesetzt zum Bohren, Honen, Räumen und Lochsägen. Ingersoll–Rand lehnt jede Haftung für Veränderungen an Werkzeugen ab, die ohne vorherige Rücksprache mit Ingersoll–Rand vorgenommen werden.
-
Page 8: Technische Daten
Griffart Freie Spannfutter– Drehzahl kapazität dB (A) gungs– intensität •Leistung U/min Zoll (mm) Druck 7802R, 7802R–EU Pistolengriff 2.000 3/8 (10) 92,8 105,8 Gemäß ANSI S5.1–1971 bei freier Drehzahl getestet ♦ Gemäß ISO8662–1 bei 80% der freien Nenndrehzahl getestet • ISO3744... - Page 9 (Name des Herstellers) Swan Lane, Hindley Green, Wigan WN2 4EZ (Adresse) erklären hiermit, gemäß unserer alleinigen Verantwortung, daß die Geräte: Umsteuerbare Hochleistungs–Bohrmaschinen der Baureihe 7802R–EU auf die sich diese Erklärung bezieht, den Richtlinien: 98/37/EG unter Anlehnung an die folgenden Grundnormen...
- Page 10 Modulo P6775 Edizione 7 Aprile, 2000 ISTRUZIONI PER TRAPANI PNEUMATICI REVERSIBILE HEAVY–DUTY MODELLI 7802R E 7802R–EU TPD1447 AVVISO I trapani modelli 7082R e 7082R–EU sono stati progettati per la trapanatura, smerigliatura, alesatura e segatura a tazza La Ingersoll–Rand non è responsabile delle modifiche apportate agli attrezzi dai clienti per adattarli ad applicazioni per le quali la Ingersoll–Rand non sia stata interpellata.
- Page 11 Capacità del mandrino dB (A) vibrazione •Potenza giri/min in (mm) Pressione 7802R, 7802R–EU Impugnatura 2.000 3/8 (10) 92,8 105,8 Collaudato secondo i criteri ANSI S5.1–1971 a velocità libera ♦ Collaudato secondo i criteri ISO8662–1 a velocità libera nominale dell’80% •...
-
Page 12: Dichiarazione Di Conformità
(nome del fornitore) Swan Lane, Hindley Green, Wigan WN2 4EZ (indirizzo) dichiariamo sotto la nostra unica responsabilità che il prodotto: Trapani pneumatici reversibile modelli 7802R–EU a cui si riferisce la presente dichiarazione è conforme alle normative delle direttive: 98/37/CE EN292 ISO8662 secondo i seguenti standard: (1994 →... -
Page 13: Uso De La Herramienta
MODELOS 7802R Y 7802R–EU TPD1447 NOTA Los Taladros Reversibles Modelos 7802R y 7802R–EU están diseñados para taladrado, rectificación, rebordeado y serrado de agujeros. Ingersoll–Rand no aceptará responsabilidad alguna por la modificación de las herramientas efectuada por el cliente para las aplicaciones que no hayan sido consultadas con Ingersoll–Rand. -
Page 14: Etiquetas De Aviso
Empuñadura Libre Portabrocas dB (A) Vibraciones •Potencia pulg. (mm) Presión 7802R, 7802R–EU pistola 2.000 3/8 (10) 92,8 105,8 Probado en conformidad con ANSI S5.1–1971 a velocidad libre ♦ Probado en conformidad con ISO8662–1 80% de la velocidad libre nominal •... -
Page 15: Declaracion De Conformidad
(nombre del proveedor) Swan Lane, Hindley Green, Wigan WN2 4EZ (domicilio) Declaramos que, bajo nuestra responsabilidad exclusiva, el producto: Taladro Reversible Modelo 7802R–EU a los que se refiere la presente declaración, cumplen con todo lo establecido en las directivas: 98/37/CE EN292 ISO8662 conforme a los siguientes estándares:... - Page 16 VOOR ZWAAR WERK TPD1447 LET WEL De Typen 7802R en 7802R–EU Omkeerbare Boormachines zijn bedoeld voor het boren, honen, ruimen en gatzagen. Ingersoll–Rand is niet aansprakelijk voor door de klant aangebrachte veranderingen aan de gereedschappen voor toepassingen waarover met Ingersoll–Rand geen voorafgaand overleg werd gepleegd.
- Page 17 Type Soort Hendel Onbelast Capaciteit toerental Houder dB (A) niveau •Vermogen in (mm) Deuk 7802R, 7802R–EU pistool 2.000 3/8 (10) 92,8 105,8 Getest volgens ANSI S5.1–1971 bij vrije snelheid ♦ Getest volgens ISO8662–1 bij 80% nominale vrije snelheid • ISO3744...
- Page 18 Ingersoll–Rand, Co. (naam leverancier) Swan Lane, Hindley Green, Wigan WN2 4EZ (adres) verklaren, onder onze uitsluitende aansprakelijkheid, dat het produkt: Typen 7802R–EU Omkeerbare Boormachines voor Zwaar Werk waarop deze verklaring betrekking heeft overeenkomt met de bepalingen van directieven: 98/37/EG EN292 ISO8662 overeenkomstig de volgende hoofdstandaards: (1994 →...
- Page 19 7802R–EU . . . EU–99 Rotor ..... . 7802R–53 Inlet Bushing ....7802–465 Vane Packet (set/5) .
- Page 20 Service Centers Centres d’entretien Niederlassungen Centri di Assistenza Centros de Servicio Service Centra Ingersoll–Rand Nederland Produktieweg 10 2382 PB Zoeterwoude Nederland Tel: (31) 71 452200 Fax: (31) 71 5218671 Ingersoll–Rand Company Ingersoll–Rand Company SA 510 Hester Drive PO Box 3720 White House Alrode 1451 TN 37188...
- Page 21 MODEL 7802R OG 7802R–EU TPD1447 BEMÆRK Reversible boremaskiner model 7802R og 7802R–EU er designet til boring, honing, fræsning og hulsavning. Ingersoll–Rand påtager sig intet ansvar for eventuelle ændringer af værktøjer udført af brugeren i forbindelse med anvendelsesområder, som Ingersoll–Rand ikke på...
- Page 22 Fri hastighed Borepatrons– kapacitet dB (A) niveau •Effekt o/min. tommer (mm) Tryk 7802R, 7802R–EU pistolgreb 2.000 3/8 (10) 92,8 105,8 Afprøvet i overensstemmelse med ANSI S5.1–1971 ved fri hastighed ♦ Afprøvet i overensstemmelse med ISO8662–1 ved 80% af dimensioneret fri hastighed •...
- Page 23 (leverandørens navn) Swan Lane, Hindley Green, Wigan WN2 4EZ (adresse) erklærer som eneansvarlig, at nedenstående produkt, Ekstra kraftige, reversible boremaskiner, model 7802R–EU som denne erklæring vedrører, overholder bestemmelserne i følgende direktiver 98/37/EC ved at være i overensstemmelse med følgende hovedstandard(er): EN292 ISO8662 (1994 →) XUA XXXXX →...
- Page 24 MODELLER 7802R OCH 7802R–EU TPD1447 OBS! Reversibla borrmaskiner, modeller 7802R och 7802R–EU är tillverkade för borrning, finslipning, upprymning och utsågning av hål. Ingersoll–Rand är inte ansvarigt för verktyg som har modifierats av kunden för att anpassas till andra användningar, om inte kunden har konsulterat Ingersoll–Rand.
- Page 25 Hastighet nivå dB (A) •Kraft varv/min. mm (tum) Tryck 7802R, 7802R–EU pistol 2 000 10 (3/8) 92,8 105,8 G Testad i enlighet med ANSI S5.1–1971 vid fri hastighet ♦ Testad i enlighet med ISO8662–1 vid 80% beräknad fri hastighet •...
-
Page 26: Försäkran Om Överensstämmelse
Ingersoll–Rand, Co. (leverantörens namn) Swan Lane, Hindley Green, Wigan WN2 4EZ (adress) intygar härmed, i enlighet med vårt fullständiga ansvar, att produkten, Reversibla tryckluftsborrar, modeller 7802R–EU som detta intyg avser, uppfyller kraven i 98/37/EG Direktiven. EN292 ISO8662 Genom at använda följande principstandard: (1994 →... -
Page 27: Bruk Av Verktøy
EKSTRA KRAFTIG REVERSERBAR, TRYKKLUFTDREVEN DRILL, MODELL 7802R OG 7802R–EU TPD1447 MERK Ekstra kraftig reverserbar trykkluftdreven drill, modell 7802R og 7802R–EU, er konstruert for boring, honing, opprømming og hullsaging. Ingersoll–Rand er ikke ansvarlig for verktøymodifikasjoner som utføres av kunden hvor Ingersoll–Rand uten at er rådspurt. - Page 28 Hastighet Chuck–kapasitet snivå dB (A) •Styrke o/min mm (tomme) Trykk 7802R, 7802R–EU pistol 2 000 10 (3/8) 92,8 105,8 G Testet i følge ANSI S5.1–1971 ved fri hastighet ♦ Testet i henhold til ISO8662–1 ved 80 % nominell fri hastighet •...
- Page 29 Ingersoll–Rand, Co. (leverandørens navn) Swan Lane, Hindley Green, Wigan WN2 4EZ (adresse) erklærer som eneansvarlig at produktet, Reverserbare trykkluftdrevne driller, modell 7802R–EU som denne erklæringen gjelder for, oppfyller bestemmelsene i EU–direktivene 98/37/CE ved å bruke følgende prinsipielle standarder: EN292 ISO8662 (1994 →...
- Page 30 7802R– JA 7802R–EU –SARJAN KAKSISUUNTAISIIN ERIKOISVAHVOIHIN PAINEILMALLA TOIMIVIIN PORAKONEISIIN TPD1447 HUOMAA 7802R– ja 7802R–EU –sarjan kaksisuuntaiset porakoneet on tarkoitettu poraamiseen, hoonaamiseen, avartamiseen ja reikien sahaamiseen. Ingersoll–Rand ei ole vastuussa työkalujen mahdollisista modifikaatioista muihin sovelluksiin, joista Ingersoll–Randille ei ole tiedoitettu. VAROITUS OHJEISSA ON MUKANA TÄRKEITÄ...
- Page 31 GMelutaso Malli Kädensijan Vapaa Istukan koko tyyppi nopeus dB (A) •Teho 1/min mm (tuumaa) Paine 7802R, 7802R–EU pistooli 2 000 10 (3/8) 92,8 105,8 G Koestettu ANSI S5.1–1971 mukaisesti vapaalla kierrosnopeudella ♦ Koestettu ISO8662–1 mukaisesti 80%:sella vapaalla kierrosnopeudella • ISO3744...
- Page 32 Ingersoll–Rand, Co. (toimittajan nimi) Swan Lane, Hindley Green, Wigan WN2 4EZ (osoite) vakuutamme ja kannamme yksin täyden vastuun siitä, että tuote 7802R–EU –sarjan kaksisuuntaiset ilmanpaineella toimivat porakoneet johon tämä vakuutus viittaa, täyttää direktiiveissä 98/37/EY esitetyt vaatimukset seuraavia perusnormeja käytettäessä: EN292 ISO8662 (1994 →...
- Page 33 TRABALHOS PESADOS MODELOS 7802R E 7802R–EU TPD1447 AVISO Os berbequins Reversiveis Modelos 7802R e 7802R–EU são concebidos para perfuran, afiar a largan e cortar fanos A Ingersoll–Rand não é responsável por modificações, feitas pelo cliente em ferramentas, nas quais a Ingersoll–Rand não tenha sido consultada.
- Page 34 Encabadouro dB (A) Punho Vibrações •Potência mm (pol.) Pressão 7802R, 7802R–EU pistola 2 000 10 (3/8) 92,8 105,8 Testada de acordo com a ANSI S5,1–1971 com velocidade livre ♦ Testada de acordo com a ISO8662–1 com 80% da velocidade livre •...
-
Page 35: Declaração De Conformidade
(nome do fornecedor) Swan Lane, Hindley Green, Wigan WN2 4EZ (endereço) declaramos sobre nossa única responsabilidade que o produto, Berbequins Pneumáticos Reversíveis Modelo 7802R–EU ao(s) qual(is) esta declaração se refere, está (ão) de acordo com as provisões da 98/37/CE Directivas EN292 ISO8662 Ao se utilizar os seguintes Princípios Standards:...