Ingersoll-Rand 7804R Instructions Manual
  1. Manuals
  2. Brands
  3. Ingersoll-Rand Manuals
  4. Drill
  5. 7804R
  6. Instructions manual

Ingersoll-Rand 7804R Instructions Manual

Reversible angle drill
Hide thumbs Also See for 7804R:
Table of Contents

Advertisement

Available languages
  • EN

Available languages

  • ENGLISH, page 1

Quick Links

Model 7804R and 7804R–EU Drills are designed for drilling, honing, reaming and hole
sawing.
Ingersoll–Rand is not responsible for customer modification of tools for applications
on which Ingersoll–Rand was not consulted.
IMPORTANT SAFETY INFORMATION ENCLOSED.
READ THIS MANUAL BEFORE OPERATING TOOL.
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THE INFORMATION
IN THIS MANUAL INTO THE HANDS OF THE OPERATOR.
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
PLACING TOOL IN SERVICE
•
Always operate, inspect and maintain this tool in
accordance with all regulations (local, state,
federal and country), that may apply to hand
held/hand operated pneumatic tools.
•
For safety, top performance, and maximum
durability of parts, operate this tool at 90 psig
(6.2 bar/620 kPa) maximum air pressure at the
inlet with 5/16" (8 mm) inside diameter air supply
hose.
•
Always turn off the air supply and disconnect the
air supply hose before installing, removing or
adjusting any accessory on this tool, or before
performing any maintenance on this tool.
•
Do not use damaged, frayed or deteriorated air
hoses and fittings.
•
Be sure all hoses and fittings are the correct size
and are tightly secured. See Dwg. TPD905–1 for a
typical piping arrangement.
•
Always use clean, dry air at 90 psig maximum air
pressure. Dust, corrosive fumes and/or excessive
moisture can ruin the motor of an air tool.
•
Do not lubricate tools with flammable or volatile
liquids such as kerosene, diesel or jet fuel.
•
Do not remove any labels. Replace any damaged
label.
The use of other than genuine Ingersoll–Rand replacement parts may result in safety hazards, decreased tool
performance, and increased maintenance, and may invalidate all warranties.
Repairs should be made only by authorized trained personnel. Consult your nearest Ingersoll–Rand Authorized
Servicenter.
Refer All Communications to the Nearest
Ingersoll–Rand Office or Distributor.
 Ingersoll–Rand Company 2000
Printed in U.S.A.
INSTRUCTIONS FOR
MODEL 7804R AND 7804R–EU
REVERSIBLE ANGLE DRILL
03539962
USING THE TOOL
•
Always wear eye protection when operating or
performing maintenance on this tool.
•
Always wear hearing protection when operating
this tool.
•
Keep hands, loose clothing and long hair away
from rotating end of tool.
•
Anticipate and be alert for sudden changes in
motion during start up and operation of any power
tool.
•
Keep body stance balanced and firm. Do not
overreach when operating this tool. High reaction
torques can occur at or below the recommended
air pressure.
•
Tool accessory may continue to rotate briefly after
throttle is released.
•
Air powered tools can vibrate in use. Vibration,
repetitive motions or uncomfortable positions may
be harmful to your hands and arms. Stop using
any tool if discomfort, tingling feeling or pain
occurs. Seek medical advice before resuming use.
•
Use accessories recommended by Ingersoll–Rand.
•
This tool is not desgined for working in explosive
atmospheres.
•
This tool is not insulated against electric shock.
Form P7115
GB
Edition 5
June, 2000

Advertisement

Table of Contents
loading

Related Manuals for Ingersoll-Rand 7804R

Summary of Contents for Ingersoll-Rand 7804R

  • Page 1 INSTRUCTIONS FOR MODEL 7804R AND 7804R–EU REVERSIBLE ANGLE DRILL Model 7804R and 7804R–EU Drills are designed for drilling, honing, reaming and hole sawing. Ingersoll–Rand is not responsible for customer modification of tools for applications on which Ingersoll–Rand was not consulted.

  • Page 2: Warning Label Identification

    Chuck Capacity Sound Level dB (A) Level • in (mm) pressure power 7804R, 7804R–EU pistol 1200 3/8 (10) 91.4 104.4 Tested in accordance with ANSI S5.1–1971 at free speed ♦ Tested in accordance to ISO8662–1 at 80% rated free speed •...

  • Page 3: Declaration Of Conformity

    Ingersoll–Rand, Co. (supplier’s name) Swan Lane, Hindley Green, Wigan WN2 4EZ (address) declare under our sole responsibility that the product, Model 7804R–EU Reversible Angle Drill to which this declaration relates, is in compliance with the provisions of 98/37/EC Directives. EN292 ISO8662 By using the following Principle Standards: (1994 →...
  • Page 4 DE LA PERCEUSE D’ANGLE RÉVERSIBLE MODÈLE 7804R ET 7804R–EU NOTE La perçeuse Modèle 7804R et 7804R–EU est destinée aux opérations de perçage, de rodage, d’alésage et de sciage de trou. Ingersoll–Rand ne peut être tenu responsable de la modification des outils par le client pour les adapter à...

  • Page 5: Mise En Service De L'outil

    Niveau de son levier mandrin dB (A) vibration • tr/mn pouces (mm) Pression Puissance 7804R, pistolet 1200 3/8 (10) 91,4 104,4 7804R–EU Testé conformément à ANSI S5.1–1971 en vitesse libre ♦ Testé conformément à ISO8662–1 a 80% vitesse libre nominale •...

  • Page 6: Certificat De Conformité

    (nom du fournisseur Swan Lane, Hindley Green, Wigan WN2 4EZ (adresse déclarons sous notre seule responsabilité que le produit: Perceuse D’Angle Réversible Modèle 7804R–EU objet de ce certificat, est conforme aux prescriptions des Directives: 98/37/CE EN292 ISO8662 en observant les normes de principe suivantes: (1994 →...
  • Page 7 GEBRAUCHSANWEISUNG FÜR HOCHLEISTUNGS–WINKELBOHRMASCHINE DER BAUREIHE 7804R UND 7804R–EU HINWEIS Winkelbohrmaschinen der Baureihe 7804R und 7804R–EU werden eingesetzt zum Bohren, Honen, Räumen und Lochsägen. Ingersoll–Rand lehnt jede Haftung für Veränderungen an Werkzeugen ab, die ohne vorherige Rücksprache mit Ingersoll–Rand vorgenommen werden.

  • Page 8: Technische Daten

    Bohrfutter– Schallpegel Drehzahl kapazität gungs– dB (A) intensität • U/min Zoll (mm) Druck Leistung 7804R, 7804R–EU Pistolengriff 1200 3/8 (10) 91.4 104.4 Gemäß ANSI S5.1–1971 bei freier Drehzahl getestet ♦ Gemäß ISO8662–1 bei 80% der freien Nenndrehzahl getestet • ISO3744...
  • Page 9 (Name des Herstellers) Swan Lane, Hindley Green, Wigan WN2 4EZ (Adresse) erklären hiermit, gemäß unserer alleinigen Verantwortung, daß die Geräte: Hochleistungs–Winkelbohrmachine Der Baureihe 7804R–EU auf die sich diese Erklärung bezieht, den Richtlinien: 98/37/EG unter Anlehnung an die folgenden Grundnormen EN292 ISO8662 entsprechen: (1994 →...
  • Page 10 ISTRUZIONI PER TRAPANI AD ANGOLO REVERSIBILE MODELLI 7804R E 7804R–EU AVVISO Il trapano modello 7804R e 7804R–EU è stato progettato per la trapanatura, smerigliatura. alesatura e segatura a tazza. La Ingersoll–Rand non è responsabile delle modifiche apportate agli attrezzi dai clienti per adattarli ad applicazioni per le quali la Ingersoll–Rand non sia stata interpellata.
  • Page 11 Capacità del d’impugnatura mandrino vibrazione dB (A) •Potenza giri/min poll. (mm) Pressione 7804R, Impugnatura 1200 3/8 (10) 91.4 104.4 7804R–EU Collaudato secondo i criteri ANSI S5.1–1971 a velocità libera ♦ Collaudato secondo i criteri ISO8662–1 a velocità libera nominale dell’80% •...

  • Page 12: Dichiarazione Di Conformità

    (nome del fornitore) Swan Lane, Hindley Green, Wigan WN2 4EZ (indirizzo) dichiariamo sotto la nostra unica responsabilità che il prodotto: Trapani ad angolo reversibile modelli 7804R–EU a cui si riferisce la presente dichiarazione è conforme alle normative delle direttive: 98/37/CE EN292 ISO8662 secondo i seguenti standard: (1994 →...
  • Page 13 TALADRO ANGULARES REVERSIBLE MODELO 7804R Y 7804R–EU NOTA Los Taladros Angulares Modelos 7804R y 7804R–EU están diseñados para taladrado, rectificación, rebordeado y serrado de agujeros. Ingersoll–Rand no aceptará responsabilidad alguna por la modificación de las herramientas efectuada por el cliente para las aplicaciones que no hayan sido consultadas con Ingersoll–Rand.

  • Page 14: Etiquetas De Aviso

    Capacidad de Libre Portapuntas Vibraciones dB (A) •Potencia pulg. (mm) Presión 7804R, pistola 1200 3/8 (10) 91.4 104.4 7804R–EU Probado en conformidad con ANSI S5.1–1971 a velocidad libre ♦ Probado en conformidad con ISO8662–1 80% de la velocidad libre nominal •...

  • Page 15: Declaracion De Conformidad

    (nombre del proveedor) Swan Lane, Hindley Green, Wigan WN2 4EZ (domicilio) Declaramos que, bajo nuestra responsabilidad exclusiva, el producto: Taladros Angulares de Modelo 7804R–EU a los que se refiere la presente declaración, cumplen con todo lo establecido en las directivas: 98/37/CE EN292 ISO8662 conforme a los siguientes estándares:...
  • Page 16 TYPEN 7804R EN 7804R–EU OMKEERBARE HAAKSE BOORMACHINES LET WEL De Typen 7804R en 7804R–EU Haakse Boormachines zijn bedoeld voor het boren, honen, ruimen en gatzagen. Ingersoll–Rand is niet aansprakelijk voor door de klant aangebrachte veranderingen aan de gereedschappen voor toepassingen waarover met Ingersoll–Rand geen voorafgaand overleg werd gepleegd.
  • Page 17 Onbelast Capaciteit toerental Houder niveau dB (A) •Vermogen in (mm) Deuk 7804R, 7804R–EU pistool 1200 3/8 (10) 91.4 104.4 Getest volgens ANSI S5.1–1971 bij vrije snelheid ♦ Probado en conformidad con ISO8662–1 80% de la velocidad libre nominal • ISO3744...
  • Page 18 Ingersoll–Rand, Co. (naam leverancier) Swan Lane, Hindley Green, Wigan WN2 4EZ (adres) verklaren, onder onze uitsluitende aansprakelijkheid, dat het produkt: Typen 7804R–EU Omkeerbare Haakse Boormachines waarop deze verklaring betrekking heeft overeenkomt met de bepalingen van directieven: 98/37/EG EN292 ISO8662 overeenkomstig de volgende hoofdstandaards: (1994 →...
  • Page 19 MAINTENANCE INSTRUCTIONS SECTION D’ENTRETIEN WARTUNG SEZIONE DI MANUTENZIONE INSTRUCCIONES DE MANTENIMIENTO ONDERHOUD (TPA1392)
  • Page 20 Throttle Lever Pin ... 107–120 Arbor ..... . 7804R–4 Reverse Valve Spring ..7804R–664 Bearing Case .
  • Page 21 Service Centers Centres d’entretien Ingersoll–Rand Niederlassungen Centri di Assistenza Centros de Servicio Service Centra Ingersoll–Rand Nederland Produktieweg 10 2382 PB Zoeterwoude Nederland Tel: (31) 71 45220 Fax: (31) 71 218671 Ingersoll–Rand Company 510 Hester Drive Ingersoll–Rand Company SA White House, TN 37188 PO Box 3720 Airode 1451 Tel: (615) 672 0321...
  • Page 24 REVERSIBLE VINKELBOREMASKINER, MODEL 7804R OG 7804R–EU BEMÆRK Vinkelboremaskiner model 7804R og 7804R–EU er designet til boring, honing, fræsning og hulsavning. Ingersoll–Rand påtager sig intet ansvar for eventuelle ændringer af værktøjer udført af brugeren i forbindelse med anvendelsesområder, som Ingersoll–Rand ikke på forhånd er blevet konsulteret om.
  • Page 25 Fri hastighed Borepatrons– kapacitet dB (A) niveau •Effekt o/min. tommer (mm) Tryk 7804R, 7804R–EU pistolgreb 1.200 3/8 (10) 91,4 104,4 Afprøvet i overensstemmelse med ANSI S5.1–1971 ved fri hastighed ♦ Afprøvet i overensstemmelse med ISO8662–1 ved 80%af dimensioneret fri hastighed •...
  • Page 26 (leverandørens navn) Swan Lane, Hindley Green, Wigan WN2 4EZ (adresse) erklærer som eneansvarlig, at nedenstående produkt, Reversible vinkelboremaskiner, model 7804R–EU som denne erklæring vedrører, overholder bestemmelserne i følgende direktiver 98/37/EF ved at være i overensstemmelse med følgende hovedstandard(er): EN292 ISO8662 (1994 →) XUA XXXXX →...
  • Page 27 BORRMASKINER REVERSIBEL, MODELLER 7804R OCH 7804R–EU OBS! Vindelborrmaskiner, modeller 7804R och 7804R–EU är tillverkade för borrning, finslipning, upprymning och hålsågning. Ingersoll–Rand är inte ansvarigt för verktyg som har modifierats av kunden för att anpassas till andra användningar, om inte kunden har konsulterat Ingersoll–Rand.
  • Page 28 Chuck–kapacitet handtag tions–nivå dB (A) •Kraft varv/min. mm (tum) Tryck 7804R, 7804R–EU pistol 1 200 10 (3/8) 91,4 104,4 G Testad i enlighet med ANSI S5.1–1971 vid fri hastighet ♦ Testad i enlighet med ISO8662–1 vid 80% beräknad fri hastighet •...

  • Page 29: Försäkran Om Överensstämmelse

    Ingersoll–Rand, Co. (leverantörens namn) Swan Lane, Hindley Green, Wigan WN2 4EZ (adress) intygar härmed, i enlighet med vårt fullständiga ansvar, att produkten, Vindelborrmaskiner reversibel, model 7804R–EU som detta intyg avser, uppfyller kraven i 98/37/EG Direktiven. EN292 ISO8662 Genom at använda följande principstandard: (1994 →...
  • Page 30 INSTRUKSJONER FOR MODELL 7804R OG 7804R–EU REVERSERBAR VINKELDRILLER MERK Bor i serien 7804R og 7804R–EU er konstruert for boring, opprømming, honing, stålbørstearbeider og hullsaging. Ingersoll–Rand er ikke ansvarlig for verktøymodifikasjoner som utføres av kunden, hvor Ingersoll–Rand ikke er rådspurt. ADVARSEL INNEHOLDER VIKTIG SIKKERHETSINFORMASJON.
  • Page 31 Type håndtak Hastighet Chuck–kapasitet jonsniva dB (A) •Styrke mm (tomme) Trykk 7804R, 7804R–EU pistol 1 200 10 (3/8) 91,4 104,4 G Testet i følge ANSI S5.1–1971 ved fri hastighet ♦ Testet i henhold til ISO8662–1 ved 80% nominell fri hastighet •...
  • Page 32 Ingersoll–Rand, Co. (leverandørens navn) Swan Lane, Hindley Green, Wigan WN2 4EZ (adresse) erklærer som eneansvarlig at produktet, Modell 7804R–EU reverserbar vindeldriller som denne erklæringen gjelder for, oppfyller bestemmelsene i EU–direktivene 98/37/CE EN292 ISO8662 ved å bruke følgende prinsipielle standarder: (1994 → ) XUA XXXXX →...
  • Page 33 Versio 5 Kesäkuu, 2000 OHJEITA 7804R– JA 7804R–EU –SARJAN VARUSTETUILLE KULMAPORAKONEILLE HUOMAA 7804R– ja 7804R–EU –sarjan porakoneet on tarkoitettu poraustöihin, hoonaukseen, avarrukseen ja reikien sahaamiseen. Ingersoll–Rand ei ole vastuussa työkalujen mahdollisista modifikaatioista muihin sovelluksiin, joista Ingersoll–Randille ei ole tiedoitettu. VAROITUS OHJEISSA ON MUKANA TÄRKEITÄ...
  • Page 34 ♦Värinä Malli Kädensija– Vapaa Istukan koko tyyppi nopeus dB (A) •Teho 1/min mm (tuumaa) Paine 7804R, 7804R–EU pistooli 1 200 10 (3/8) 91,4 104,4 G Koestettu ANSI S5.1–1971 mukaisesti vapaalla kierrosnopeudella ♦ Koestettu ISO8662–1 mukaisesti 80%:sella vapaalla kierrosnopeudella • ISO3744...
  • Page 35 Ingersoll–Rand, Co. (toimittajan nimi) Swan Lane, Hindley Green, Wigan WN2 4EZ (osoite) vakuutamme ja kannamme yksin täyden vastuun siitä, että tuote 7804R–EU –sarjan varustetut kulmaporakoneet johon tämä vakuutus viittaa, täyttää direktiiveissä 98/37/EY EN292 ISO8662 esitetyt vaatimukset seuraavia perusnormeja käytettäessä: (1994 → ) XUA XXXXX →...
  • Page 36 OS BERBEQUINS ANGULARES REVERSÍVEIS MODELOS 7804R E 7804R–EU AVISO Os Berbequins Angulares Reversíveis Modelos 7804R e 7804R–EU são concebidos para perfurar, afiar, alargar e rectificar furos. A Ingersoll–Rand não é responsável por modificações, feitas pelo cliente em ferramentas, nas quais a Ingersoll–Rand não tenha sido consultada.
  • Page 37 Bucha dB (A) Punho Vibrações •Potência mm (pol.) Pressão 7804R, 7804R–EU pistola 1 200 10 (3/8) 91,4 104,4 Testada de acordo com a ANSI S5.1–1971 com velocidade livre ♦ Testada de acordo com a ISO8662–1 com 80% da velocidade livre •...

  • Page 38: Declaração De Conformidade

    (nome do fornecedor) Swan Lane, Hindley Green, Wigan WN2 4EZ (endereço) declaramos sobre nossa única responsabilidade que o produto, Berbequins Angulares Reversíveis Modelo 7804R–EU ao(s) qual(is) esta declaração se refere, está (ão) de acordo com as provisões da 98/37/CE Directivas EN292 ISO8662 Ao se utilizar os seguintes Princípios Standards:...

This manual is also suitable for:

7804r–eu

Table of Contents