Advertisement
Loading the Dishwasher
Before placing the dishes in the dishwasher, remove the larger
food particles to the prevent the filter from becoming clogged, which
results in reduced performance.
If the pots and pans have baked-on food that is extremely hard to
remove, we recommend that they be allowed to soak before they
are washed. This will eliminate the need for extra wash cycles.
Pull out the rack to facilitate loading the dishwasher.
How to Use the Lower Rack
We recommend that you place the most difficult to clean items on
the bottom rack: pots, pans, lids, serving dishes and bowls, as
shown in the figure to the right.
It is preferable to place serving dishes and lids on the sides of the
racks in order to avoid blocking the rotation of the top spray arm.
- Pots, serving bowls, etc. must always be placed face down.
- Deep pots should be slanted to allow the water to flow out.
- The silverware basket can be doubled (see fig. A) so that only
one section may be used when the silverware load is light. This
also makes space for additional pots and pans and it can also be
placed in the upper rack.
- Silverware should be placed in the silverware basket with the
handles at the bottom; if the rack has side baskets, the spoons
should be located individually into the appropriate slots. Espe-
cially long utensils should be placed in the horizontal position at
the front of the upper rack.
How to Use the Upper Rack
The upper rack is designed to hold more delicate and lighter
dishware, such as glasses, coffee and tea cups and saucers, as
well as plates, small bowls and shallow pans (as long as they are
not too dirty).
- Position the dishes and cookware so that they do not get moved
by the spray of water.
The upper rack can be adjusted for height (see fig.B).
Lower Rack
Upper Rack
Load for 12 Standard Settings
fig.A
.5.
Turning on the Appliance
Starting a wash cycle
After having completed all of the installation steps in the preced-
ing paragraphs, turn on the water all the way and press the ON-
OFF button (B) located on the control pannel. The "A" indicator
light will come on. At this point, the appliance is on but you must
wait a few seconds before programming the setting for the cycle.
Setting and Starting a wash Cycle
Select the desired cycle by pressing the selector button (I). Each
time the button is pressed, one of the "J" cycle indicator lights will
come on in succession. Choose the wash cycle you feel is most
appropriate for the type of dishes that need washing (consult the
wash cycle table contained in this manual, especially when first
using the appliance). After a few seconds, the wash cycle has
begun and can no longer be changed. If necessary, read the para-
graph entitled "Cancelling or modifying a cycle while underway "
Cancelling or modifying a cycle while underway
Premise : A cycle that is underway can only be modified if it has
only been running for a short time. Otherwise, the detergent may
have already been used, and the appliance mayhave already
drained the wash water. If this is the case, the detergent dis-
penser must be refilled (see the paragraph entitled, "Loading
the Detergent"). To modify a cycle that is already underway,
press the ON/OFF button (B) that all of the settings will be
cancelled. To set a new cycle, following the instructions con-
fig.B
tained in the paragraph entitled "setting and starting a wash
cycle".
Wash cycle Program Light
The dishwasher is equipped with a LED indicator light (J) that
turns on blinks when the appliance is running the wash cycle indi-
cated by the light itself.
At the end of the wash cycle
As six acoustic signals will indicate that the wash cycle has fin-
ished and the cycle indicator light (J) for the cycle will begin to
die out. Turn off the appliance using the ON-OFF button. Turn
off the water supply to the appliance and open the door. Wait a
few minutes before unloading the dishwasher to avoid handling
the dishes and utensils while they are still hot and more suscep-
tible to breakage. They will also dry better.
GB
GB
Setting the Wash Cycle with a Delayed Start Time
By pressing the "D" button (see close-up view-'Control panel")
the start of wash cycle can be delayed for between 1 to 9 hours.
Each time the button is pressed, the display (C) will show the
number of hours for the delay period. Choose the amount of
time desired. After selecting the wash cycle, a short acoustic sig-
nal will sound and after a few seconds, the delay time on the dis-
play will blink indicating that the countdown has begun.
After the time has lapsed, the cycle will start.
NOTE:
During the delay period, it is preferable not to change any of the
settings, If this is necessary, all of the settings must be cancelled
by pressing the ON/OFF button (B).
At this point, all of the steps for "setting the wash cycle with a
Delayed Start Time" and "Setting and Starting a wash cycle" must
be repeated, following the instructions contained in the correspond-
ing sections.
If the door is opened to the unit during the delay period, the count-
down will stop. It wil begin again when the door is closed.
All of the wash cycle set to reverse time function, we may in
focus stat circulate time.
Wash Cycle adjustment Buttons
1/2 load Button
This button (see "close-up View - Control Panel", letter"E") make
it possible to wash dishes using only the upper rack if there are
not enough dishes for a full load. This will allow you to save on
water and eletrical energy. It can be used before setting any of
the wash cycle, except for the intensive cycle ( if included in the
wash cycle table). Please keep in mind that the amount of deter-
gent should also be cut in half.
.6.
Hide quick links:
Advertisement
