Usb Interface; Ipod; Network - Pioneer sc-lx87 Operating Manual

13

USB interface

Symptoms Causes
The folders/files stored on a The folders/files are currently stored
USB memory device are not in a region other than the FAT (File
displayed. Allocation Table) region.
The number of levels in a folder is
more than 9.
The audio files are copyrighted.
A USB memory device is The USB memory device does not
not recognized. support the mass storage class
specifications.
A USB hub is currently being used.
This receiver recognizes the USB
memory device as a fraud.
A USB memory device is Some formats of USB memory
connected and displayed, devices, including FAT 12, NTFS, and
but the audio files stored HFS, cannot be played back on this
on the USB memory device receiver.
cannot be played back.
The file format cannot be properly
played back on this receiver.
The USB memory cannot be —
operated with the remote
control.

iPod

Symptoms Causes
iPod is not recognized. This receiver recognizes the iPod as
a fraud.
iPod touch/iPhone/iPad is The iPod's operation may be
not recognized or otherwise unstable.
does not operate properly.
iPod cannot be operated —
with the remote control.
Remedies
Store the folders/files in the FAT region.
Limit the maximum number of levels in a folder to 9 (page
52).
Copyrighted audio files stored on a USB memory device
cannot be played back (page 52).
Try using a USB memory device compatible with the mass
storage class specifications. Note that there are cases
where even the audio files stored on a USB memory device
compatible with the mass storage class specifications are
not played back on this receiver (page 52).
Connect the USB memory device and switch on this
receiver (page 41).
This receiver does not support USB hubs (page 52).
Switch off and on again this receiver.
Reconnect the USB device with the receiver switched off.
Change to an input other than iPod/USB, then set the input
back to iPod/USB.
Check whether the format of your USB memory device is
either FAT 16 or FAT 32. Note that the FAT 12, NTFS, and
HFS formats cannot be played back on this receiver (page
52).
See the list of file formats that can be played back on this
receiver (page 53).
Press iPod USB to set the remote control to the iPod USB
control mode.
Remedies
Switch off and on again this receiver.
Reconnect the iPod with the receiver switched off.
Change to an input other than iPod/USB, then set the input
back to iPod/USB.
Try performing the operation below.
1. Press the sleep/sleep cancel button on the iPod touch/
iPhone/iPad simultaneously with the home button for at
least 10 seconds to restart the device.
2. Turn this receiver's power on.
3. Connect the iPod touch/iPhone/iPad to this receiver.
Press iPod USB to set the remote control to the iPod USB
control mode.

Network

Symptoms Causes
Cannot access the network. The LAN cable is not firmly con-
nected.
The router is not switched on.
Internet security software is cur-
rently installed in the connected
component.
The audio component on the net-
work which has been switched off is
switched on.
Playback does not start The component is currently discon-
while "Connecting..." con- nected from this receiver or the
tinues to be displayed. power supply.
The network function can- —
not be operated with the
remote control.
The PC or Internet radio is The corresponding IP address is not
not properly operated. properly set.
The IP address is being automati-
cally configured.
The audio files stored on Windows Media Player 11 or
components on the net- Windows Media Player 12 is not cur-
work, such as a PC, cannot rently installed on your PC.
be played back.
Audio files recorded in MPEG-4
AAC or FLAC are being played back
on Windows Media Player 11 or
Windows Media Player 12.
The component connected to the
network is not properly operated.
The component connected to the
network does not permit file sharing.
The folder stored on the component
connected to the network has been
deleted or damaged.
Network connections could be
restricted due to the computer's net-
work settings, security settings, etc.
Supported file formats vary by server.
As such, files not supported by your
server are not displayed on this unit.
The audio files are copyrighted.
116
FAQ
Remedies
Firmly connect the LAN cable (page 39).
Switch on the router.
There are cases where a component with Internet security
software installed cannot be accessed.
Switch on the audio component on the network before
switching on this receiver.
Check whether the component is properly connected to
this receiver or the power supply.
Press NET to set the remote control to the network function
control mode.
Switch on the built-in DHCP server function of your router,
or set up the network manually according to your network
environment (page 102).
The automatic configuration process takes time. Please
wait.
Install Windows Media Player 11 or Windows Media Player
12 on your PC (page 65).
Audio files recorded in MPEG-4 AAC or FLAC cannot be
played back on Windows Media Player 11 or Windows
Media Player 12. Try using another server. Refer to the
operation manual supplied with your server.
Check whether the component is affected by special cir-
cumstances or is in the sleep mode.
Try rebooting the component if necessary.
Try changing the settings for the component connected to
the network.
Check the folder stored on the component connected to
the network.
Check the computer's network settings, security settings,
etc.
For more information check with the manufacturer of your
server.
DRM-protected audio files cannot be played back on this
receiver.