Mhl; Built-In Avnavigator; Controlling The Rest Of Your System Usb Interface; Usb Interface - Pioneer Elite SC-99 Operating Instructions Manual

Table of Contents

Advertisement

13
Symptom
Remedy
4K video is not output even though a
When the MAIN/HDZONE setting is MAIN and the HDMI output setting is OUT 1+2 and
4K compliant TV is connected.
when the MAIN/HDZONE setting is HDZONE and HDZONE is the same input as with the
main zone, video is output with the lower resolution of the TV connected to HDMI OUT 1
and HDMI OUT 2. When there is only one 4K compliant TV, connect it to HDMI OUT 1
and set the HDMI output setting to OUT 1 or turn off HDZONE so that video is only output
to the 4K compliant TV.
Even though a 4K/60p 4:4:4 24 bit
Set the HDMI 4K/60p signal input setting to 4:4:4
compatible TV is connected, the
When the HDMI cable does not support 4K/60p 4:4:4 24 bit (18 Gbps transmission), video
4K/60p 4:4:4 24 bit video image is not
images may not be output properly. In that case, replace the cable with a compatible
output correctly.
HDMI cable or change the HDMI 4K/60p signal input setting to 4:2:0 to watch the 4K/60p
4:2:0 24 bit video image.
The HDMI OUT 3 terminal does not output a 4K/60p 4:4:4 24 bit video image if
MAIN/HDZONE is set to HDZONE. Set MAIN/HDZONE to MAIN or use the HDMI OUT
1 or HDMI OUT 2 terminals.
You cannot input 4K/60p 4:4:4 24 bit video from HDMI IN 3 to the IN 7 terminal. Use the
BD IN, HDMI IN 1 or HDMI IN 2 terminal.

MHL

Symptom
Remedy
When playing an MHL-compat-
The MHL device will not operate unless power is being supplied from this receiver. When
ible device connected to the
this receiver is in the Standby Through mode, power cannot be supplied due to reduced
HDMI 7/MHL terminal, the Standby
power consumption. Because of this, the MHL device will not operate. This is not a mal-
Through function does not work and
function.
the power turns off.
MHL-compatible device cannot be
Press MHL to set the remote control to the MHL control mode.
operated with the remote control.
MHL POW ERR is displayed on the
There is a problem with the power supply for the MHL device. After turning OFF the
display.
receiver, disconnect the MHL device, connect the MHL device again and then turn ON
the power of the receiver.
If the error is displayed even though the above operation is repeated several times,
there is a problem with the receiver or the MHL device. Disconnect the power cable and
request repair.

Built-in AVNavigator

Symptom
Cause
AVNavigator does not inter-
The receiver's power is not turned on.
act well with the receiver.
The receiver or computer is not con-
nected to the LAN.
The router's power is off.
Network connections could be
restricted due to the computer's net-
work settings, security settings, etc.
(page 94
).
Remedy
Turn the receiver's power on. (Wait about 60 seconds after
the power turns on for network functions to start.)
Connect a LAN cable to the receiver or computer
(page 47
).
Turn the router's power on.
Check the computer's network settings, security settings, etc.
Symptom
Cause
In the middle of
This is to avoid failure of the receiver
Wiring Navi, you are
due to a short-circuit between cables
instructed to turn off the
or from static electricity.
power of the unit and then
connect other equipment or
speakers.
When the Wiring Navi or
This is because of the browser's
security function.
Interactive Operation Guide
is launched, a warning
about security protection
appears on the browser.
AVNavigator screen is not
This receiver's IP address has not
displayed on the browser.
been entered into the browser cor-
rectly.
Receiver settings cannot be
JavaScript is disabled on the internet
made from a browser.
browser.
The browser is not compatible with
JavaScript.

USB interface

Symptom
Cause
The folders/files stored on a
The folders/files are currently stored
USB memory device are not
in a region other than the FAT (File
displayed.
Allocation Table) region.
The number of levels in a folder is
more than 9.
The audio files are copyrighted.
A USB memory device is
The USB memory device does not
not recognized.
support the mass storage class
specifications.
A USB hub is currently being used.
This receiver recognizes the USB
memory device as a fraud.
A USB memory device is
Some formats of USB memory
connected and displayed,
devices, including FAT 12, NTFS, and
but the audio files stored
HFS, cannot be played back on this
on the USB memory device
receiver.
cannot be played back.
The file format cannot be properly
played back on this receiver.
127
FAQ
Remedy
Per the Wiring Navi instructions, turn OFF the power
of the receiver. As long as the browser has not quit,
Wiring Navi resumes guidance upon turning ON the
receiver.
This is not a problem. Perform the operation to authorize
the blocked contents.
Check the receiver's IP address and enter it correctly in the
browser
(page 58
).
Enable JavaScript.
Use an internet browser that is compatible with JavaScript.
Remedy
Store the folders/files in the FAT region.
Limit the maximum number of levels in a folder to 9
(page
66
).
Copyrighted audio files stored on a USB memory device
cannot be played back
(page 66
).
Try using a USB memory device compatible with the mass
storage class specifications. Note that there are cases
where even the audio files stored on a USB memory device
compatible with the mass storage class specifications are
not played back on this receiver
(page 66
).
Connect the USB memory device and switch on this
receiver
(page 48
).
This receiver does not support USB hubs
(page 66
).
Switch off and on again this receiver.
Reconnect the USB device with the receiver switched off.
Change to an input other than iPod/USB, then set the input
back to iPod/USB.
Check whether the format of your USB memory device is either
FAT 16 or FAT 32. Note that the FAT 12, NTFS, and HFS formats
cannot be played back on this receiver
(page 66
).
See the list of file formats that can be played back on this
receiver
(page 67
).
 
 
 
 

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Elite sc-97

Table of Contents