Connecting Speakers - JBL SDR-35 Quick Start Manual

Connecting Speakers

To connect each of the speakers, unscrew the
corresponding terminals on the back of the Receiver, OUTPUT1 ZONE2
OUTPUT2
eARC OUT
insert the speaker wires through the hole in each post
and screw the terminals down. Make sure that the red
Z2 OUT LINE OUT STB GAME AV BD PVR CD
(positive/ ) terminal of the speaker is connected to the
+
red (positive/ ) terminal on the back panel, and the
+
black (negative/ ) terminal of the speaker is connected
–
to the black (negative/ ) terminal on the back panel.
ANALOGUE AUDIO –
SUB2 SPEAKER OUTPUTS
ZONE2 R
8Ω LOAD IMPEDANCE RECOMMENDED
HEIGHT1 R
SR FR C FL SL
SBR
C SBL
SBR
SR FR C FL SL
SUB1 SBR HEIGHT1 R
ZONE2 R
It is important that no stray strands of wire from these
connections are allowed to touch another cable or the back
panel. Failure to ensure this can cause a short circuit and
damage your Receiver.
Ensure the unit is switched off while connecting speakers.
Do not over-tighten the loudspeaker terminals, or use a
wrench, pliers, etc., as this could damage the terminals and
this would not be covered under the product's warranty.
Speaker cables
The speakers should be connected to the amplifier using
high-quality, copper cables. A heavy gauge (thick copper)
and as short as practical is ideal. The gauge should be heavier
(a lower number) for longer runs. Using speaker cables that
are too long and/or thin gauge can significantly degrade the
sound quality.
Connections to the speaker terminals should always be
finger tight, whether using bare wires or spade connectors.
Bi-amping the Front Left & Front Right speakers
Bi-amping is the use of two amplifier channels per speaker. Bi-amping can provide better sound quality than conventional
single wiring. If you do not have Surround Back speakers (i.e. you have a 5.1 surround system, not a 7.1 system) then you
can use the spare Surround Back speaker outputs to bi-amplify the front left and right speakers, if your speakers support bi-
PVR UHD BD SAT AV GAME
amping. The spare channels can alternatively be used to power stereo speakers in another room (Zone 2).
HDMI
Speakers that support bi-amping have two sets of +/- terminals per speaker, usually linked together by metal strips. These
DIGITAL AUDIO
SAT PVR
TRIG Z1 Z1 IR
metal strips MUST be removed when bi-amping; failure to remove them will result in damage to the amplifier that is not
FM/DAB
covered under warranty.
To bi-amp the front left and right speakers, remove the metal strips from the speaker terminals. Connect the woofer or LF
TRIG Z2 Z2 IR
BD CD STB AV OUT
terminals to the FL and FR terminals on the Receiver. Connect the tweeter or HF terminals to the SBL and SBR terminals on
the Receiver. Finally, navigate to the Setup Menu 'Spkr Types' and set the 'Use Channels 6+7 for' menu option to 'BiAmp L+R';
see page EN-32.
ZONE2 L
HEIGHT1 L
SBL
SBL
ETHERNET
HEIGHT1 L
ZONE2 L
USB 5V/0.5A
WI-FI
HEIGHT2 HEIGHT1 Z2 OUT LINE OUT STB GAME
Link MUST
L
LINK MUST BE REMOVED
be removed
R
CH13/14 CH15/16
WI-FI
L
SUB2
Connecting subwoofers
ZONE2 R
R
HEIGHT1 R
SBR
PREAMP OUT
PREAMP OUT
FL SL C SBL
SBR
FR SR SUB1 SBR HEIGHT1 R
ZONE2 R
The Receiver also allows up to four active subwoofers to be connected to the
subwoofer handbook for the correct setting up and connection procedure for your particular subwoofer(s).
STB
WI-FI BLUETOOTH
RS232
SBR FL SBL
FR
OUTPUT1 CAMBRIDGE, CB25 9PB, UK ZONE2
PVR UHD
OUTPUT2
eARC DESIGNED IN THE UK OUT
MADE IN VIETNAM
HDMI
AV BD PVR CD SAT
FM/DAB
ETHERNET
OUTPUT1
OUTPUT2
eARC
USB 5V/0.5A
ANALOGUE AUDIO
BD
HEIGHT2 HEIGHT1 Z2 OUT LINE OUT STB GAME AV BD PVR CD
SPEAKER OUTPUTS
ZONE2 L
L 8Ω LOAD IMPEDANCE RECOMMENDED
HEIGHT1 L
SR C FL SL
FR
SBL
R
ANALOGUE AUDIO
CH13/14 CH15/16
L
SUB2 SPEAKER OUTPUTS
ZONE2 R
8Ω LOAD IMPEDANCE RECOMMENDED
R
HEIGHT1 R
SR FR C
SBR
SBL
SR FR C FL SL
PREAMP OUT
HEIGHT1 L
ZONE2 L
PREAMP OUT
FL SL
C SBL
SBR
SR FR C
FR SR SUB1 SBR HEIGHT1 R
ZONE2 R
EN-16
Using external power amplifiers
The internal power amplifier of the Receiver can be
supplemented or replaced with external power amplification,
such as the JBL Synthesis SDA-7120 or SDA-2200. Connect
ETHERNET
the
WI-FI
HEIGHT2 HEIGHT1
L
R
CH13/14 CH15/16
L
R
PREAMP OUT
FL
BD SAT AV GAME STB
FR
WI-FI
DIGITAL AUDIO
PVR
TRIG Z1 Link MUST Z1 IR FL, FR
be removed
LINK MUST BE REMOVED
Connect these to the equivalent Right and Left front
RS232
channels of your power amplifier.
ZONE2
PVR UHD BD SAT
OUT
TRIG Z2 Z2 IR C
CD STB AV OUT
HDMI
Connect these to the Center front channel of your power
DIGITAL AUDIO
SAT PVR
amplifier.
FM/DAB
SUB
Subwoofer outputs. Connect this to the input of your active
BD CD STB AV OUT
subwoofer(s), if present.
SR, SL
ZONE2 L
Surround Right and Surround Left outputs. Connect these
HEIGHT1 L
FL SL
SBL
to the Surround Right and Left power amplifier inputs.
CAMBRIDGE, CB25 9PB, UK
SBR, SBL
Surround Back Right and Surround Back Left outputs.
or outputs. Refer to your
Connect these to the Surround Back Right and Surround
Back Left power amplifier inputs.
SBL
FL SL
HEIGHT1 L
ZONE2 L Height 1 (Height Front), Height 2 (Height Back)
Height Front and Height Back. Connect these to the Height
channel power amplifier inputs.
All preamplifier analog outputs are buffered, have a low
output impedance and are at line level. They are able to drive
long cables or several inputs in parallel if required.
OUTPUT1 ZONE2
OUTPUT2
eARC OUT
USB 5V/0.5A sockets to your power amplifier inputs:
Z2 OUT LINE OUT STB GAME AV BD PVR CD
ANALOGUE AUDIO
SUB2 SPEAKER OUTPUTS
ZONE2 R
8Ω LOAD IMPEDANCE RECOMMENDED
HEIGHT1 R
SR FR C FL
SBR
PREAMP OUT
SL
C SBL
SBR
SR FR C FL
SR SUB1 SBR HEIGHT1 R
ZONE2 R
BLUETOOTH
AV GAME STB
WI-FI BLUETOOTH
TRIG Z1 Z1 IR
RS232
TRIG Z2 Z2 IR
DESIGNED IN THE UK
MADE IN VIETNAM
CAMBRIDGE, CB25 9PB, UK
DESIGNED IN THE UK
MADE IN VIETNAM
PVR UHD
S
FM/DAB
B
ZONE2 L
HEIGHT1 L
SL
SBL
SBL
SL
HEIGHT1 L
ZONE2 L