Table of Contents
Advertisement
Quick Links
DUCT TYPE AIR CONDITIONER
INSTRUCTION
MANUAL
AD242AMNAC
AU242ANNAC
(HDU-24CL03/M(R1))
AD28NAMNAC
AU28NANNAC
(HDU-28CM03/M(R1))
AD36NAMNAC
AU36NAPNAC
(HDU-36CM03/M(R1))
AD42NAMNAC
AU42NAPNAC
(HDU-42CM03/M(R1))
No. 0010571463
AD242AMBAC
AU242ANBAC
(HDU-24HL03/M(R1))
AD28NAMBAC
AU28NANBAC
(HDU-28HL03/M(R1))
AD36NAMBAC
AU36NAPBAC
(HDU-36HM03/M(R1))
AD42NAMBAC
AU42NAPBAC
(HDU-42HM03/M(R1))
Advertisement
Table of Contents
Related Manuals for Haier AD242AMBAC
Summary of Contents for Haier AD242AMBAC
- Page 1 DUCT TYPE AIR CONDITIONER INSTRUCTION MANUAL AD242AMNAC AU242ANNAC (HDU-24CL03/M(R1)) AD28NAMNAC AU28NANNAC (HDU-28CM03/M(R1)) AD36NAMNAC AU36NAPNAC (HDU-36CM03/M(R1)) AD42NAMNAC AU42NAPNAC (HDU-42CM03/M(R1)) No. 0010571463 AD242AMBAC AU242ANBAC (HDU-24HL03/M(R1)) AD28NAMBAC AU28NANBAC (HDU-28HL03/M(R1)) AD36NAMBAC AU36NAPBAC (HDU-36HM03/M(R1)) AD42NAMBAC AU42NAPBAC (HDU-42HM03/M(R1))
-
Page 2: Table Of Contents
TABLE OF CONTENTS CAUTIONS SAFETY PRECAUTIONS PARTS AND FUNCTIONS OPERATION MALFUNCTION CARE AND MAINTENANCE FOR PREPARATION OF HEATING IS THE UNIT INSTALLED CORRECTLY INSTALLATION MANUAL FOR WIRE CONTROLLER INSTALLATION MANUAL FOR OUTDOOR UNIT INSTALLATION MANUAL FOR INDOOR UNIT 9-14 15-16 20-21 22-25 26-31... -
Page 3: Cautions
Damaged air conditioners are not to be put into operation. In case of doubt, consult your supplier. Use of the air conditioner is to be carried out in strict compliance with the relative instructions set forth in the User's Guide. - Page 4 Unless the circuit breaker is installed, it could cause elecrical shocks. Install on the place where can endure the weight of air conditioner. Bodily injury could result by a careless installation. WARNING Do not poke the air inlet or outlet with a bar, etc.
-
Page 5: Safety Precautions
If the structure is not repaired immediately, the unit could topple down to ca apersonal injury. WARNING When the air conditioner is relocated, contact your dealer or a pro- fessional installer. Improper practice of installation could cause water leakage, electric shock or Make sure to use a fuse of proper electric rating. - Page 6 6. The breaker of the air conditioner should be all-pole switch; and the distance between its two contacts should be no less 3mm.
-
Page 7: Parts And Functions
PARTS AND FUNCTIONS Indoor Unit Air outlet For series 24,28 Outdoor Unit Connecting piping and electrical wiring Air inlet Air outlet For series 24,28 Duct Air outlet Air inlet For series 36,42 Air inlet Air outlet Drain hose Duct Air inlet Compressor (Inside of unit) For series 36,42... -
Page 8: Operation
PARTS AND FUNCTIONS Operation CLOCK Used to set correct time. TIMER Used to select TIMER ON, TIMER OFF, TIMER ON/OFF. TIME Used to set clock and timer setting. Power ON/OFF Used for unit start and stop. Cautions: On cooling only unit, heating mode is not available. -
Page 9: Parts And Functions
PARTS AND FUNCTIONS Operation HEAT COOL AUTO FAN SPEED TIMER ON TIMER OFF CLOCK Clock set When unit is started for the first time, clock should be adjusted as follows: Press CLOCK button, "AM"or "PM" flashes. Press to set correct time. Each press will increase or decrease 1min. If the button is kept depressed, time will change quickly. - Page 10 OPERATION The air conditioner has the function of POWER FAILURE RESUME. Fan operation Enjoy yourself by just a gentle press. (1) Unit start Press ON/OFF button, unit starts. Previous operation status appears on display. (Not Timer setting) Power indicator lights up.
- Page 11 OPERATION AUTO RUN, COOL,HEAT and DRY operation Recommendations (1) Unit start Press ON/OFF button, unit starts. Previous operation status appears on display (Not Timer setting). Power indicator lights up. (2) Select operation mode Press MODE button. For each press, operation mode changes as follows: AUTO COOL HEAT...
-
Page 12: Timer Operation
OPERATION TIMER operation Set Clock correctly before starting Timer operation. You can let unit start or stop automatically at following time: Before you wake up in the morning, or get back from outside or after you fall asleep at night. TIMER ON/OFF (1)After unit start, select your desired operation mode. - Page 13 OPERATION TIMER ON-OFF (1)After unit start, select your desired operation mode Operation mode will be displayed on LCD. Power indicator lights up. (2) Press TIMER button to change TIMER mode Every time the button is pressed, display changes as follows: Select (3)Time setting for TIMER ON Press TIME button.
- Page 14 Press SLEEP button once to make the air conditioner have the previous-set sleep time (first power- on is "1h"), the sleep symbol will appear. Press time button hours. Each press of , the time increases/reduces 1 hour and "xh"...
- Page 15 Notes: When a power failure suddenly occurs during the air conditioner is working after the power failure compensation is set, if the air conditioner will not be used for a long time, please cut off the power supply to prevent its operation from being resumed after the power is supplied again, or press the "Switch On/Off"...
-
Page 16: Malfunction
Isn't it warming up? page 9 When the air conditioner does not operate properly after you have checked the above mentioned items or when the following phenomenon is observed, stop the operation of the air conditioner and contact your sales dealer. -
Page 17: Malfunction
Water or steam generates from the outdoor unit during heating. When the air conditioner is started, when the compressor starts or stops during operation or when the air conditioner is stopped, it sometimes sounds "shuru shuru" or "gobo gobo". It is the flowing sound of the refrigerant, and it is not a trouble. -
Page 18: Care And Maintenance
Operate the unit with FAN mode on a fair day for about half a day to dry the inside of the unit well. Stop operation and turn off the power supply switch. Electric power is consumed even the air conditioner is in stop. -
Page 19: For Preparation Of Heating
Defrosting operation When a room is warmed with a heat pump type air conditioner, frost accumulates on the heat ex- changer of outdoor unit along with the drop of indoor temperature. Since the accumulated frost re- duces the effect of warming, it is necessery to automatically switch the operation to the defrosting mode. -
Page 20: Is The Unit Installed Correctly
Besides, construction expense is charged for removal or reinstallation. The capacity of air conditioner will decrease by contamination of inside of unit when it is used for about three years although depending upon the circumstances under which it is used, and so in addition to the usual maintenance service, special inspection/maintenance service is necessary. -
Page 21: Installation Manual For Wire Controller
INSTALLATION MANUAL FOR WIRE CONTROLLER 1. Remove upper part of wire controller Remove upper part of wire controller by press. PCB is mounted on lower part of wire controller, be careful not to damage it. Upper part of wire controller 2. - Page 22 INSTALLATION MANUAL FOR WIRE CONTROLLER 3. Indoor unit wiring Connect terminals (A,B,C,D) on lower part of wire controller to terminals (A, B,C,D) on PCB of indoor unit. wiring from here Lower part of wire controller Upper part of wire controller Hint Tread surface of the terminal well so that shielding may not contact other part.
-
Page 23: Installation Manual For Outdoor Unit
INSTALLATION MANUAL FOR OUTDOOR UNIT <Heat Pump model/Cooling Only model > BE SURE TO READ THESE INSTRUCTIONS CAREFULLY BEFORE BEGINNING INSTALLATION. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD CAUSE SERIOUS INJURY OR DEATH, EQUIPMENT MALFUNCTION AND/OR PROPERTY DAMAGE. BE SURE TO READ INSTALLATION MANUAL FOR INDOOR UNIT WITH THIS MANUAL. 1. - Page 24 INSTALLATION MANUAL FOR OUTDOOR UNIT 4. Refrigerant piping (1) Outline piping (2) Piping size Model 36,42 series Gas piping 19.05(3/4")x1.0mm Liquid piping 9.52(3/8")x0.8mm Install the removed flared nuts to the pipes to be connected, then flare the pipes. (3) Limitations for one way piping length and vertical height difference. One way piping length: less than 30m (for 24,28 series).
-
Page 25: Electric Wiring
After attaching the each caps, check the gas leakage around the caps. CAUTION: If the refrigerant of the air conditioner leaks, it is necessary to make all the refrigerant out, then charge the liquid refrigerant into air conditioner according to the amount marked on the name plate. -
Page 26: Installation Manual For Outdoor Unit
INSTALLATION MANUAL FOR OUTDOOR UNIT (2) Wiring connection Make wiring to supply power to the outdoor unit, so that the power for the indoor unit is supplied by 1 and 2 terminals. Circuit breaker Outdoor Earth leakage unit breaker HIGH VOLTAGE Interconnecting wires (For 36,42 series, 28 series... - Page 27 Take care that wiring does not rise upward, and accurately install the lid/service panel. Its improper installation can also result in heat generation or fire. When setting up or moving the location of the air conditioner, do not mix air etc. or anything other than the designated refrigerant (R407C) within the refrigeration cycle.
-
Page 28: Installation Manual For Indoor Unit
INSTALLATION MANUAL FOR INDOOR UNIT All Wiring of this installation must comply with NATIONAL, STATE AND LOCAL REGULATIONS. These instructions do not cover all variations for every kind of installation circumstance. Should further information be desired or should particular problems occur, the matter should be referred to your local distributor. BE SURE TO READ THESE INSTRUCTIONS CAREFULLY BEFORE BEGINNING INSTALLATION. - Page 29 INSTALLATION MANUAL FOR INDOOR UNIT (4) Preparation for suspending the unit (a) Size of hole at ceiling and position of hanging bolts <Combination with silent panel> (Hanging bolt position) Model 36,42 series 24,28 series (b) Hanger bolts installation Use care of the piping direction when the unit is installed. Hole-in anchor Hole-in plug (Ceiling hole size)
- Page 30 INSTALLATION MANUAL FOR INDOOR UNIT (5) Installation of indoor unit Fix the indoor unit to the hanger bolts. If required, it is possible to suspend the unit to the beam, etc. Directly by use of the bolts without using the hanger bolts. Note When the dimensions of main unit and ceiling holes does not match, it can be adjusted with the slot holes of hanging bracket.
- Page 31 INSTALLATION MANUAL FOR INDOOR UNIT When constructing drain piping for several units, position the common pipe about 100 mm below the drain outlet of each unit as shown in the sketch. Use VP-30(11/4") or thicker pipe for this purpose. Be sure to provide heat insulation to hard PVC pipes of indoor placement.
- Page 32 Use the rear fresh air inlet when the simultaneous intake and exhaust is conducted. (Side inlet cannot be used.) ii) Exhaust (Make sure to use also the suction.) Use the side exhaust port. Air conditioner main unit Heat inlet duct insulation...