DeWalt D27111 Manual page 31


WARNING: Always transport the machine in bench saw mode and ensure that the
saw blade is completely covered by the upper guard. Never use any guard to carry
the machine.
MAINTENANCE
Your D WALT power tool has been designed to operate over a long period of time with a
e
minimum of maintenance. Continuous satisfactory operation depends upon proper tool care
and regular cleaning.

WARNING: To reduce the risk of injury, turn unit off and disconnect machine
from power source before installing and removing accessories, before adjusting
or changing set-ups or when making repairs. Be sure the trigger switch is in the OFF
position. An accidental start-up can cause injury.
• If the saw blade does not stop in less than 10 seconds after switching off, have the
machine serviced by an authorised D
e
Lubrication
This machine requires no additional lubrication. The bearings of the motor are pre-lubricated
and watertight.
• Avoid using oil or grease as this can cause clogging with sawdust and chips and
create problems.
• Clean the parts subject to accumulation of sawdust and chips periodically with a dry brush.
Cleaning
Before use, carefully check the upper blade guard, movable lower blade guard as well as
the dust extraction tube to determine that it will operate properly. Ensure that chips, dust or
workpiece particle cannot lead to blockage of one of the functions.
In case of workpiece fragments jammed between saw blade and guards disconnect the
machine from the power supply and follow the instructions given in section Mounting the
Saw Blade. Remove the jammed parts and reassembling the saw blade.

WARNING: Blow dirt and dust out of the main housing with dry air as often as dirt is seen
collecting in and around the air vents. Wear approved eye protection and approved dust
mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic
parts of the tool. These chemicals may weaken the materials used in these parts. Use a
cloth dampened only with water and mild soap. Never let any liquid get inside the tool;
never immerse any part of the tool into a liquid.

WARNING: To reduce the risk of injury, regularly clean the table top.

WARNING: To reduce the risk of injury, regularly clean the dust collection system
Cleaning and Maintaining the Kerf Plate (Fig. U)
Regularly clean the area below the kerf plate.
If the kerf plate is worn it must be replaced.
1. Remove the screws 73 holding the kerf plate
2. Remove the kerf plate and clean the area below.
3. Re-install the parts of the kerf plate and the screws.
4. Tighten the screws hand-tight.
5. To adjust the kerf plate, proceed as follows:
a. Pull down the head until the blade just enters the saw kerf.
b. Adjust each part of the kerf plate to fit closely to the teeth of the blade.
c. Tighten the screws.
Optional Accessories

WARNING: Since accessories, other than those offered by D
with this product, use of such accessories with this tool could be hazardous. To reduce the
risk of injury, only D WALT recommended accessories should be used with this product.
e
Support for Long Pieces (Fig. A4)
1. Always support long pieces.
2. For best results, use the extension work support
(available from your dealer as an option). Support long workpieces using any convenient
means such as saw-horses or similar devices to keep the ends from dropping.
Dust Collection Port (Fig. A5, V)

WARNING! Whenever possible, connect a dust extraction device designed in accordance
with the relevant regulations regarding dust emission.
1. The D27111 will accept the optional dust collection port. For installation, refer to the dust
collection port instructions when purchased.
2. The D27112 will accept and is supplied with the dust collection port.
Connect a dust collection device designed in accordance with the relevant regulations. The air
velocity of externally connected systems shall be 20 m/s ±2 m/s. Velocity to be measured in
the connection tube at the point of connection, with the tool connected but not running.
Saw Blades
ALWAYS USE 305 mm SAW BLADES WITH 30 mm ARBOR HOLES. SPEED RATING MUST BE
AT LEAST 4000 RPM. Never use a smaller or greater diameter blade. It will not be guarded
properly. Use cross cut blades only. Do not use blades designed for fast ripping, combination
blades or blades with hook angles in excess of 10°.
WALT repair agent.
8 .
WALT, have not been tested
e
27 to extend the table width of your saw
BLADE DESCRIPTIONS
APPLICATION
construction saw Blades (thin kerf with anti-stick rim)
General Purpose
Woodworking saw Blades (provide smooth, clean cuts)
Fine crosscuts
Consult your dealer for further information on the appropriate accessories.
Protecting the Environment
Separate collection. Products and batteries marked with this symbol must not be
disposed of with normal household waste.
Products and batteries contain materials that can be recovered or recycled reducing
the demand for raw materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at www.2helpU.com.
EnGLIsh
DIAMETER TEETH
305 mm 36
305 mm 60
29