Wahl 1874 Operating Manual page 13

Operation
Preparation
Keep the packaging material for safe storage or transport
later.
f Check that the contents are complete.
f Check all the parts for possible transport damage.
Safety
Caution! Damage due to incorrect power supply.
f Only operate the hair clipper with the voltage stated on
the nameplate.
Charging the battery
This cordless hair clipper is supplied with two battery packs. While the
appliance is in use, the second battery pack can be recharged on the
charging stand. This means that the hair clipper is always ready for use.
Before the hair clipper is used for the first time, each battery
pack should be charged for the following times:
·
STANDARD BATTERY pack approx. 50 minutes
·
XXL BATTERY pack (optionally available) approx.
120 minutes.
1. Connect the appliance plug (R) on the plug-in transformer (S) to the
plug socket (H) of the charging stand (Fig. 2ⓐ).
2. Connect the plug-in transformer to the mains socket (Fig. 2ⓑ).
3. Insert the battery pack into the recess of the charging stand (Fig. 4).
The charging process starts.
·
During charging, the charging indicator (D) flashes red.
·
It should take around 50 minutes for the STANDARD BAT-
TERY pack to charge to full capacity.
·
It should take around 120 minutes for the XXL BATTERY
pack (optionally available) to charge to full capacity.
·
The second battery can remain in the charging stand so
that a charged battery pack is always available.
4. Once the charging process has finished, the charging indicator (D)
lights up green.
Battery operation
1. Switch on the hair clipper using the on/off switch and switch off
after use (Fig. 5ⓐ/ⓑ).
·
In case of insufficient maintenance of the blade set, the
operating time can be reduced considerably.
·
While in operation with a fully charged battery, the
charging indicator (D) lights up green.
·
Whenever the charging indicator (D) lights up red during
operation, the battery pack needs to be recharged. You
can now use the charged replacement battery pack.
To recharge the battery:
1. Switch off the hair clipper using the on/off switch (Fig. 5ⓑ).
2. Press the release button (C) on the side and remove the battery
pack (Fig. 3ⓐ).
3. Remove the charged battery pack (Fig. 4) from the charging stand
and slide it into the hair clipper until it locates with an audible click
(Fig. 3ⓑ).
4. Fit the flat battery pack to the charging stand (Fig. 4). See section
Charging the battery.
Operation
Setting the cutting length
The cutting length can be adjusted to between 0.7 mm and 3 mm (5
possible positions) using the cutting-length adjustment (G) integrated
into the blade set (Fig. 6).
Cutting with the attachment comb
The hair clipper can also be operated with attachment combs.
f In order to achieve the indicated cutting length, the cutting length
adjustment lever (G) should be set to position 1 (Fig. 6).
Depending on the model, the following attachment combs
are included as standard:
3 mm, 6 mm, 9 mm and 12 mm, 18 mm and 25 mm cutting
lengths.
Attaching/removing the attachment comb
1. Slide the attachment comb on to the blade set in the direction of
the arrow until it reaches the limit stop (Fig. 7ⓐ).
2. The attachment comb can be removed by pushing it in the direc-
tion of the arrow (Fig. 7ⓑ).
Maintenance
Warning! Injuries and material damage due to incorrect
handling.
f Switch off the hair clipper before cleaning it or perform-
ing any maintenance.
f Disconnect the charging station from the power supply
before cleaning it.
Cleaning and care
Danger! Electric shock due to penetration of liquid.
f Do not immerse the hair clipper in water!
f Do not allow any liquid to get inside the hair clipper.
Caution! Danger from aggressive chemicals.
Aggressive chemicals could damage the hair clipper and
accessories.
f Never use solvents or scouring agents.
f Only use cleaning agents and blade set oil recom-
mended by the manufacturer.
Accessories and spare parts are available from your dealer or
our service centre.
f Remove the attachment comb (Fig. 7ⓑ) and lift the blade set out
of the housing (Fig. 8ⓐ), see replacement of the blade set .
f Use the cleaning brush (Q) to remove any cut hairs from the hous-
ing opening and from the blade set (Fig. 9).
E N G L I S H
de
en
fr
it
es
pt
nl
da
sv
no
fi
tr
pl
cs
sk
hr
hu
sl
ro
bg
ru
uk
et
lv
lt
el
13
ar