Related Manuals for Safe Fleet RVS-082575
Summary of Contents for Safe Fleet RVS-082575
- Page 1 Instruction Manual Backup Camera System with Waterproof Quad View Monitor and Heated Camera RVS-082575 RVS Systems, Inc. © 2016 Reverse With Confidence ™...
-
Page 2: Table Of Contents
Introduction....... 03 Safety Information......04-06 Before Beginning Installation . -
Page 3: Introduction
NOTE! Please read all of the installation instructions carefully before installing the product. Improper installation will void manufacturer’s warranty. Congratulations on purchasing a Rear View Backup Camera System! With this manual you will be able to properly install and operate the unit. The Backup Camera System is intended to be installed as a supplement aid to your standard rear view mirror that already exists in your vehicle. -
Page 4: Safety Information
Please read the entire manual and follow the instructions and warnings carefully. Failure to do so can cause serious damage and/or injury, including loss of life. Be sure to obey all applicable local traffic and motor vehicle regulations as it pertains to this product. Improper installation will void manufacturer’s warranty. - Page 5 INSTALLATION: • Electric shock or product or disconnected wire may cause a malfunction may occur if this fire. product is installed incorrectly. • While installing the Rear View System be careful with the wire • Use this product within positioning in order to avoid wire the voltage range specified.
- Page 6 If you have questions about this product, contact: RVS Systems 1797 Atlantic Avenue Brooklyn, NY 11233 Tel: 1.888.881.2601 IN NO EVENT SHALL SELLER OR MANUFACTURER BE LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.
-
Page 7: Before Beginning Installation
Before drilling please check that no cable or wiring is on the other side of the wall. Please clamp all wires securely to reduce the possibility of them being damaged while vehicle is in use. Keep all cables away from hot or moving parts and electrical noisy components. We recommend doing a benchmark test before installation to insure that all components are working properly. -
Page 8: Installation Guide
Wiring After connecting the monitor to the power harness, plug the camera into the CAM 3 input. Connect the RED 12V power wire to an ignition power source and the BLACK 12V ground wire to a chassis ground. The BROWN wire is the REVERSE trigger wire. Connect this wire to the vehi- cle’s backup light circuit to activate the rear view image whenever the vehicle shifts into reverse. - Page 9 Precautions For Use Of Monitor I. The monitor is made of glass and plastic. Do not subject it to a mechanical shock by dropping it from a high place, etc. II. Do not apply excessive force to the monitor surface or the adjoining areas since this may cause the color tone to vary.
- Page 10 Components RVS Systems Waterproof Camera...
- Page 11 7” Waterproof Quad View Monitor with a TFT LCD digital color touch screen display. Monitor comes with a U-Bracket, swivel head mount, and a waterproof rating of IP69K. • 7” Quad View Display with multiple viewing options • Completely waterproof - IP69K •...
-
Page 12: Monitor
Monitor Dimensions Dimension 7” TV System NTSC/ PAL Resolution 800 x 3 (RGB) x 480 Brightness 400 cd/m² Contrast 500 :1 Viewing Angle U: 50°/ D: 60°, R/L: 70° Aspect Ratio 16:9 Operating Temperature -10 ~ +65ºC Storage Temperature -30 ~ +80ºC Power Consumption Max. - Page 13 Reverse With Confidence ™...
- Page 14 1. Remote control signal sensor 2. Power button 3. Increase / decrease volume and switch sub-menu values 4. Menu selection and toggle display mode (SINGLE/DUAL/TRIPLE/ QUAD/PIP IMAGE) 5. Menu button 6. Jump Key - Immediately view predetermined display mode RVS Systems...
-
Page 15: Connections
Connections Reverse With Confidence ™... -
Page 16: Remote
Remote Operations 1. MUTE: MUTE / UNMUTE volume 2. POWER: Turn monitor ON / OFF 3. MENU: Toggle between menus 4. UP: Toggle selection UP RVS Systems... - Page 17 5. DN: Toggle selection DOWN & toggle display mode (SINGLE/ DUAL/TRIPLE/QUAD/PIP IMAGE) 6. VOL: Decrease volume & toggle sub-menu values VOL: Increase volume & toggle sub-menu values 8. MODE: Toggle display mode (SINGLE/DUAL/TRIPLE/QUAD/PIP IMAGE) 9. SEL.: Toggle jump key 10. P/N: Toggle between PAL/NTSC 11.
-
Page 18: Osd Setup
On-Screen Display (OSD) • SCALE: Toggle distance grid lines ON/OFF. When ON, distance grid lines will be displayed when backup camera (CAM 3) is triggered. • INPUT SCAN: Toggle camera input auto identification. When ON, monitor will display connected cameras and skip inputs not connected. •... -
Page 19: Trigger Setting
Trigger Setting • TURN IMAGE: Display options when side cameras (CAM 1, CAM 2) are trig- gered. When on SINGLE, the corresponding camera will display when either camera is triggered. When on SPLIT, a split image of side and rear view camera will be displayed when either side camera is triggered. -
Page 20: Jump Key
Jump Key Setting RVS Systems... - Page 21 • REC-V OUT: Toggle which camera view will record when a DVR is attached (LEFT/RIGHT/FRONT/QUAD). • AUTOSCAN: When setting is ON, the monitor automatically switches be- tween connected camera inputs and quad view. • SCAN DELAY: Toggle AUTOSCAN delay (0-60 seconds). •...
-
Page 22: Touch Screen Operations
When in quad view, press any channel to view full screen RVS Systems... - Page 23 Touch screen menu Reverse With Confidence ™...
- Page 24 Exchange picture locations of any two cameras displayed in multi-viewing mode RVS Systems...
- Page 25 Swap display position (dual/ triple view) Reverse With Confidence ™...
- Page 26 Switch to next display mode Switch to previous display mode RVS Systems...
-
Page 27: Camera
Camera Dimensions Reverse With Confidence ™... - Page 28 Camera Specifications Image Device 1/3” SONY® Super HAD CCD TV System PAL/NTSC Total Number Of Pixels PAL: 537 (H) x 597 (V) / NTSC: 537 (H) x 505 (V) Effective Pixels PAL: 500 (H) x 582 (V) / NTSC: 510 (H) x 492 (V) Sensing Area 4.9 mm (H) x 3.7 mm(V) Sync.
-
Page 29: Troubleshooting
Troubleshooting Problem Possible Causes/Solutions Adaptor is connected incorrectly. Improper power supply. No picture/sound Unit is off. No picture Check cable connection. Audio cable improperly connected. Volume is off or set very No sound low. Dark picture Adjust brightness/contrast. Low environmental temperature. No color Adjust the color settings. -
Page 30: Warranty & Disclaimer
ONE YEAR WARRANTY RVS SYSTEMS, INC. WARRANTS THIS PRODUCT AGAINST MATERIAL DEFECTS FOR A PERIOD OF ONE YEAR FROM DATE OF PURCHASE. WE RESERVE THE RIGHT TO REPAIR OR REPLACE ANY SUCH DEFECTIVE UNIT AT OUR SOLE DISCRETION. RVS SYSTEMS, INC. IS NOT RESPON- SIBLE FOR A DEFECT IN THE SYSTEM AS A RESULT OF MISUSE, IMPROPER INSTALLATION, DAMAGE OR MISHANDLING OF THE ELECTRONIC COMPONENTS. - Page 31 DISCLAIMER RVS SYSTEMS AND/OR ITS AFFILIATES DOES NOT GUARANTEE OR PROMISE THAT THE USER OF OUR SYSTEMS WILL NOT BE IN/PART OF AN ACCIDENT OR OTHERWISE NOT COLLIDE WITH AN OBJECT AND/OR PERSON. OUR SYSTEMS ARE NOT A SUBSTITUTE FOR CAREFUL AND CAU- TIOUS DRIVING OR FOR THE CONSISTENT ADHERENCE TO ALL APPLICABLE TRAFFIC LAWS AND MOTOR VEHICLE SAFETY REGULATIONS.
- Page 32 If you have any questions about this product, contact: RVS SYSTEMS, Inc. 1797 Atlantic Avenue Brooklyn, NY 11233 888.881.2601 Better Cameras. Better Service. IT’S OUR GUARANTEE. RVS Systems...