Advertisement
Quick Links
Advertisement
Related Manuals for Omron SYSMAC Series
Summary of Contents for Omron SYSMAC Series
- Page 1 Communication Interface Manual Published by M2I Corporation M2I Corporation...
- Page 2 OMRON SYSMAC Series OMRON SYSMAC-C Serial Interface The following section describes the system configuration and interface between Samsung OMRON SYSMAC-C PLC and TOP using RS-232C/422 Serial Communication. < System Configuration > The above figure shows system configuration to connect SYSMAC-C PLC to TOP.
- Page 3 Caution Be cautious that Communication Unit of C200H/C200HS differs from other in connector pin spec. (Refer connection diagram (2),(4)) < Cable Diagram > (1) RS-232C (SYSMAC-C ↔ TOP (for 9/15 Pin Connector) This is connection diagram for SYSMAC-C PLCs except C200, CS1, CJ1,CPM1A, 2A, 2C.
- Page 4 (3) RS-422 (SYSMAC-C ↔ TOP (for 5Pin Terminal Block or 15Pin Connector ) This is connection diagram for SYSMAC-C PLCs except C200. Comm. Link Module(9Pin) (5Pin Terminal Block/15pin) 1/11 2/12 3/13 4/14 5/15 ↔ TOP (for 5Pin Terminal Block or 15Pin (4) RS-422 (SYSMAC-C200 Connector) ) This is connection diagram for SYSMAC-C PLC C200.
- Page 5 < SYSMAC-C PLC Setup > (1) C200H-LK201-V1/LK-202-V1 Setup 1) Set station number. Station Number is set by SW1 and SW2. SW1 is X10, SW2 is X1. 2) Baud Rate Setting Set by SW3. Setting values according to SW Set are as follows. Switch Baud Rate(bps) 1200...
- Page 6 Level 1,2 available Level 1,2,3 available Disable setting 4) DIP Switch Setting C200H-LK201-V1 C200H-LK202-V1 Terminator Mode Exist CTS Toggle External None 0V(Always ON) SW No. OFF Fixed OFF Fixed 5V Supply None REF. Recommended Setting is CTS 0V(On), 1:N, Terminator Exist.
- Page 7 (2) C500-LK201-V1 Dip Switch Setup 입출력포트 IO port RS422 RS422 RS232 RS232 Sync. 동기 Internal 내부 External 외부 Terminal Resister 종단 저항 None 무 유 External 외부 Setting Switch Status Switch Setting Item … Assign Station Num. … … … Station Num.
- Page 8 REF. Other recommended settings are Internal Sync., Terminator, CTS OV. REF. Fixed to Parity Even, Data Bit 7, Stop Bit 2. (3) C500-LK203 Dip Switch Setting 5V Supply In/Out Port RS422 RS232 Sync. Internal External Terminator None Exist External Set Switch Status Switch Setting Item …...
- Page 9 Set Switch Status Switch Setting Item 1200 2400 4800 9600 1920 Assign Baud Rate Baud Rate Setting Select System System#0 System#1 Mode Command Level 1,2,3 Command Level Setting REF. Other recommended settings are Internal Sync., Terminator, CTS OV.
- Page 10 (4) C120-LK201-V1/LK-202-V1 Setting 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 Set Switch Status Switch Setting Item … Assign Station Num. … … … Station Num.
- Page 11 ① C120-LK201-V1 Switc Setting Item Set Switch Status CTS Setting CTS Always ON External CTS Sync. Type Internal Sync. External Sync. Not Used Not Used ② C120-LK202-V1 Switch Setting Item Set Switch Status Terminator Exist None Not Used Not Used REF.
- Page 12 (5) C200HW-COM06 Setup This is setting for OMRON C200 PLC. Settings use internal DM area. (Refer PLC manual in detail.) Default Settings are RS232C, 9600, 7bit, 2bit, even. Caution During communication, Mode of PLC must be „MONITOR‟. Otherwise, „Write‟ to PLC is not available.
- Page 13 < TOP Setup > (1) TOP Designer Setup Select “OMRON(SYSMAC-C)”of “OMRON Series” in PLC Type. (2) TOP Serial Setup Serial Settings are as follows. Serial Baud Rate : Same as controller‟s setting. Serial Data Bit : Same as controller‟s setting.
- Page 14 CPM1A/2A /2C Setup < System Configuration > The above figure shows system configuration to connect SYSMAC-CPM1A/2A Type PLC to TOP. Comm. Unit Cable Refer cable CPM1A/ CPM1-CIF01 diagram(RS-232C) CPM2A Refer cable (block Type) CPM1-CIF11 diagram(RS-422) CPM2C- Refer cable ALL TOP CIF01 Diagram(RS-232C) CPM2C...
- Page 15 (2) RS-422 ( CPM1A/2A ↔ TOP) CPM1A/2A/2C(9Pin) TOP(5Pin Terminal/15Pin) RDB(RD+) 1/11 2/12 3/13 4/14 SDB(SD+) 5/15 RDA(RD-) SDA(SD-) < TOP Setup > (1) TOP Designer Setup Select “OMRON(SYSMAC-C)”of “OMRON Series” in PLC Type.
- Page 16 (2) TOP Serial Setup Serial Settings are as follows. Serial Baud Rate : Same as controller‟s setting. Serial Data Bit : Same as controller‟s setting. Serial Stop Bit : Same as controller‟s setting. Serial Parity Bit : Same as controller‟s setting. ...
- Page 17 Available Address List (1) SYSMAC C Series(Common) Input 50,120(F),500(F) 2000H, 200H(S), 1000H(F) Data Link 0~31 0~63 Latch Relay 0~31 0~99 Timer 0~127 0~511 Counter 0~127 0~511 Data Memory Refer following List. Aux. Memory None 0~27 I/O Relay 0~63 0~255 (0~511:200HS) (DM Area) C50,120,500 0~511...
- Page 18 (3) SYSMAC CS1 Series Addr Index Register 0~15 Task Flag(TK) 0~30 Data Register 0~15 Timer(CV) 0~4095 Counter(CV) 0~4095 Data Memory 00000~32767 Internal AUX. Relay 0~511 Channel I/O 0~6143 Hold Relay 0~511 Special Auxiliary Relay 0~959 Exp. Data Memory(E0~EC) E0~EC 0~32767 Exp.
Need help?
Do you have a question about the SYSMAC Series and is the answer not in the manual?
Questions and answers