Makita DVC867L Instruction Manual page 14

Switch action
► Fig.7: 1. Stand-by switch 2. Power button 3. Suction
force adjusting knob
To start the cleaner:
1. Set the stand-by switch to the "I" side. The cleaner
gets into stand-by state.
2. Press the power button.
To make the cleaner get into stand-by mode, press the
power button again.
To turn off the cleaner, set the stand-by switch to the
"O" side.
The suction power can be adjusted according to your
work need.
Suction power can be increased by turning the suc-
tion force adjusting knob from the
the symbol.
NOTICE:
Always set the stand-by switch to the "O"
side when not using the cleaner for long time. The
cleaner consumes power during stand-by state.
Locking or unlocking the caster
► Fig.8: 1. Caster 2. Stopper lever 3. FREE position
4. LOCK position
Locking the caster is convenient when storing the
cleaner, stopping the work on the way and keeping the
cleaner still.
To operate the stopper, move it by hand.
To lock the caster with a stopper, lower the stopper
lever and the caster no longer will rotate. To release the
caster from the locked position, raise the stopper lever.
NOTE: When moving the cleaner, make sure that
the caster is unlocked. Moving the cleaner with the
caster in the locked position may cause damage to
the caster.
Carriage handle
When carrying the cleaner, carry it by holding the han-
dle on the head. The handle is retractable at the head
when not in use.
► Fig.9
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
CAUTION:
Always wear dust mask during
assembly or maintenance.
Installing the powder filter (HEPA)
and prefilter (for dry dust)
uids or wet dusts when using the powder filter.
Picking up such things may cause the powder filter
breakage.
To use powder filter:
1.
mounting position markings.
2.
place them in the prefilter while aligning the mounting
position markings.
3.
symbol to
► Fig.10: 1. Tank cover 2. Powder filter (HEPA)
NOTICE:
sure that prefilter and damper are used together. It
is not allowed to install powder filter alone.
Installing the paper pack
Optional accessory
use the prefilter together that is preinstalled on
the tool. Failure to use the prefilter together may
cause unusual noise and heat, resulting in a fire.
sure that powder filter, damper and prefilter are
always used together.
1.
2.
opening of the cleaner.
3.
the holder so that it is positioned at the end beyond the
detent protrusion.
► Fig.11: 1. Paper pack 2. Holder
Installing the polyethylene bag
Cleaner can also be used without polyethylene bag.
However, using polyethylene bag is easier to empty the
tank without letting your hands dirty.
Spread the polyethylene bag in the tank. Insert it
between the holder plate and the tank, and pull it to the
hose inlet.
► Fig.12: 1. Holder plate 2. Polyethylene bag
Spread the bag around the top of the tank so that the
prefilter edge can catch and hold the bag securely.
► Fig.13: 1. Prefilter
NOTE: A polyethylene bag available on the
market can be used. 0.04 mm or thicker one is
recommended.
NOTE: Too much dust will tear the bag easily, so
do not collect the dust more than the half of the bag
capacity.
14 ENGLISH
CAUTION:
Never pick up water or other liq-
Place the prefilter in the tank while aligning the
Mount the damper on the powder filter and then
Mount the tank cover and lock it.
3. Damper 4. Prefilter 5. Tank 6. Mounting
position marking
Before using the powder filter, make
WARNING:
When using the paper pack, also
CAUTION:
Before using the paper pack, make
Extend the paper pack.
Align the paper pack opening with the dust suction
Insert the cardboard part of the paper pack onto