Advertisement
WaRNING! Do not switch the saw on whilst the blade is in contact with the workpiece. Bring the rotating blade to the workpiece.
and avoid un-intentional starting of the saw.
Do not hold the workpiece by hand. use base vice to secure the workpiece.
Do not use the saw for a task it is not designed to perform.
Do not allow untrained persons to operate the saw.
Do not get the saw wet or use in damp or wet locations or areas where there is condensation.
WaRNING! Do not use saw where there are flammable liquids, solids or gases such as petrol, paint solvents, waste wiping rags etc.
Do not operate the saw if any parts are missing or damaged as this may cause failure and/or personal injury.
Do not remove the safety guard whilst in use.
Do not attempt to remove a workpiece until the blade has stopped rotating.
Do not touch the workpiece close to the cut as it will be very hot. Allow to cool.
Do not leave the saw operating unattended.
Do not operate the saw when you are tired or under the influence of alcohol, drugs or intoxicating medication.
When not in use switch the saw off and isolate from the power supply. store in a safe, dry, childproof area.
2. aPPlICatION & SPeCIFICatIONS
the sM2254 is a circular saw designed to cut ferrous metal - including structural steel - bars and pipes. It should not be used to cut any other
materials. Blade guard, bar stop, integral workpiece vice and coolant system are included.
Specifications:
Blade sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .see Blade chart
Max.cutting capacity. . . . . . . . . . . . . . . . . . . . . . . . . . . .see Blade chart
Max. vice opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80mm
Motor (Input/output) . . . . . . . . . . . . . . .230V 50Hz, 4.5Amps / 750Watts
Blade speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52rpm
Mitre cuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0-45º
coolant . . . . . . . Water + sealey sco/5L soluble oil (minimum 10% oil)
coolant capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.0ltr
oil (gear box) . . . . . . . . . . . . . . . . . . . . . .Mobil Glycole 30 or equivalent
oil capacity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.4ltr
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60Kg
sound pressure level- average . . . . . . . . . . . . . . . . . . . . . . . . 65dB(A)
Blade Chart
Workpiece
Dia. mm
10 - 80
10 - 80
20 - 80
20 - 80
solid bar
3. CONteNtS & aSSeMBlY
WaRNING! for safe handling and movement use a lift truck or crane. slings should be positioned as
shown in fig 1.
3.1.
unpack the product and check that all components and tools are present and undamaged.
If any problem is noted contact your supplier immediately.
3.2.
set the saw on a flat, stable work bench, or surface strong enough
to support the saw and any workpiece.
Mount the unit to the working surface, as shown in fig.2, using
screws and expansion plugs. Ensure that it is sitting level.
saw can be positioned directly on a cement floor using screws &
expansion plugs or tie rods sunk in cement.
Be sure to maintain a safe distance between the saw and any
walls/machinery. A minimum of 800mm clearance is required at
the rear.
- peak . . . . . . . . . . . . . . . . . . . . . . . . . . . 70dB(A)
tube
Max blade dia. 225mm
Wall mm
tooth pitch mm
<2
4-6
8
2 - 5
5 - 10
8
>10
8
<20
8
20-50
10
Original Language Version
SM 2254
shape
B shaped
c solid
c solid
c solid
c solid
c solid
fig 1
fig 2
sM2254
Issue: 2 - 17/12/09
Advertisement
