Page 1: Introduction
TABLE OF CONTENTS SECTION ............. 3 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 3: Table Of Contents
CONTENTS Introduction ......4 How To Use This Manual ....4 Warnings And Cautions .
Page 4: Introduction
4 INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully.
Page 5 INTRODUCTION 5...
Page 6: Vehicle Identification Number
6 INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information.
Page 7: Vehicle Modifications / Alterations
INTRODUCTION 7 VEHICLE MODIFICATIONS / ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 9: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 Ignition Key Removal ....12 Key-In-Ignition Reminder .
Page 10 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Disarm The System ....19 Security System Manual Override ...19 Illuminated Entry System .
Page 11 Seat Belt Extender ..... .49 Driver And Front Passenger Supplemental Restraint System - Airbag ....50 Event Data Recorder (EDR) .
Page 12: Things To Know Before Starting Your Vehicle 9
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your dealer. Ask your dealer for these numbers and keep them in a safe place.
Page 13 NOTE: If you try to remove the key before you place the lever in PARK, the key may become trapped temporarily in the ignition cylinder. If this occurs, rotate the key to the right slightly, then remove the key as described. If a malfunction occurs, the system will trap the key in the ignition cylinder to warn you that this safety feature is inoperable.
Page 14: Key-In-Ignition Reminder
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Key-In-Ignition Reminder If you open the driver’s door and the key is in the ignition switch, a chime will sound to remind you to remove the key. Locking Doors With The Key You can insert the key with either side up.
Page 15: Automatic Transaxle Ignition Interlock System
Automatic Transaxle Ignition Interlock System This system prevents the key from being removed unless the shift lever is in PARK. It also prevents shifting out of PARK unless the key is in the ACC, or ON positions, and the brake pedal is depressed. SENTRY KEY —...
Page 16: Shaft Lock Module (Vehicles Equipped With Premium Security System) - If Equipped
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Shaft Lock Module (Vehicles Equipped with Premium Security System) — If Equipped The shaft lock module is located inside the steering column. The module works in conjunction with the Sentry Key to prevent the steering shaft from rotating if someone inserts an invalid ignition key into the ignition lock cylinder in the instrument panel.
Page 17: Customer Key Programming
NOTE: When having the Sentry Key Immobilizer System serviced, bring all vehicle keys with you to the dealer. Customer Key Programming You can program new sentry keys to the system if you have two valid sentry keys by performing the following procedure: 1.
Page 18: General Information
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information The Sentry Key system complies with FCC rules part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. •...
Page 19: To Disarm The System
NOTE: If the SECURITY light stays on continuously during vehicle operation, have the system checked by your dealer. To Disarm the System: Use the Keyless Entry transmitter to unlock the door. If something has triggered the system in your absence, the horn will sound three times when you unlock the doors and the security lamp will flash for 30 seconds.
Page 20: Illuminated Entry System
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ILLUMINATED ENTRY SYSTEM The courtesy lights will turn on when you use the keyless entry transmitter or open the doors. The lights will fade to off after about 30 seconds or they will immediately fade to off once the ignition switch is turned on.
Page 21: To Unlock The Doors And Liftgate
Two (2) transmitters may be supplied with the vehicle. Vehicles built without the powered options will be equipped from the factory with three button transmitters and those built with power options will be equipped with six button transmitters. Keyless Entry Transmitter THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 To unlock the doors and liftgate: Press and release the UNLOCK button on the transmitter...
Page 22: To Lock The Doors And Liftgate
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • On non EVIC – equipped vehicles perform the follow- ing steps: 1. Perform this operation while standing outside the vehicle. 2. Press and hold the UNLOCK button on your key fob. 3.
Page 23: To Open/Close Power Liftgate - If Equipped
• On non EVIC – equipped vehicles perform the follow- ing steps: 1. Perform this operation while standing outside the vehicle. 2. Press and hold the LOCK button on your key fob. 3. Continue to hold the LOCK button, wait at least 4 seconds, but no longer than 10 seconds, then press and hold the PANIC button.
Page 24: Using The Panic Alarm
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • On electronic vehicle information center (EVIC) equipped vehicles refer to “Flash Lights On Lock/ Unlock?” under “Use Factory Settings?” in the EVIC section of this manual. • On non EVIC - equipped vehicles perform the follow- ing steps: 1.
Page 25: Programming Additional Transmitters
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 Programming Additional Transmitters Refer to SENTRY KEY “Customer Key Programming.” NOTE: If you do not have a programmed transmitter, contact your authorized dealer for assistance. Battery Replacement The recommended replacement battery is CR2032 bat- tery.
Page 26 26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Remove and replace the battery. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 3. To reassemble the transmitter case, snap the two halves together.
Page 27: Door Locks
DOOR LOCKS Manual Door Locks Lock the doors by pushing up on the lock knob on each door trim panel. Door Lock Plunger THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 If the lock knob is up when you shut the door, the door will lock.
Page 28: Power Door Locks
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks A power door lock switch is on each front door trim panel. Use this switch to lock or unlock the doors. Power Door Lock Switch If you press the power door lock switch while the key is in the ignition, and any front door is open, the power locks will not operate.
Page 29 If desired, the “Auto Door Locks?” feature can be turned on or off by using the following procedure: • On electronic vehicle information center (EVIC) equipped vehicles refer to “Auto Door Locks?” under “Use Factory Settings?” in the EVIC section of this manual.
Page 30 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE This feature will not operate if there is any manual operation of the power door locks (Lock or Unlock). If desired, the “Auto Unlock On Exit?” feature can be turned on or off by using the following procedure: •...
Page 31: Child Protection Door Lock
Child Protection Door Lock To provide a safer environment for small children riding in the rear seats, the rear doors are equipped with a child protection door lock system. NOTE: When the child lock system is engaged, the door can be opened only by using the outside door handle even though the inside door lock is in the unlocked position.
Page 32 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: For emergency exit with the system engaged, move the door lock knob to the UNLOCK position, roll down the window and open the door with the outside door handle. WARNING! Avoid trapping anyone in the vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged.
Page 33: Windows
WINDOWS Power Windows The window controls on the driver’s door control all the door windows. The switches will operate only when the ignition switch is in the ON or ACCESSORY position. Power Window Switches THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 The window lock switch on the driver’s door allows you to disable the window controls on the passenger doors.
Page 34 34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The time is customer programmable through the Elec- tronic Vehicle Information Center (EVIC). Refer to “Power Accessory Delay?” under “Personal Settings (Customer Programmable Features)” in Section 4 of this manual for details. Auto Up Feature with Anti–Pinch Protection —...
Page 35: Liftgate
Reset Any time the vehicle battery is disconnected, or goes dead, the auto-up function will be disabled. To reactivate the auto-up feature, perform the following steps after vehicle power is restored: 1. Pull the window switch up to close window com- pletely and continue to hold the switch up for an additional two seconds after the window is closed.
Page 36 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Once unlocked, on vehicles equipped with power locks, the liftgate can be opened or closed without using the key. To open the liftgate, depress the liftgate release switch located on the underside of the license plate bar and pull the liftgate open with one fluid motion.
Page 37: Power Liftgate - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 Power Liftgate — If Equipped The power liftgate may be opened manually or by using the button on the remote keyless entry transmitter. Press the button on the remote keyless entry transmitter twice within five seconds, to open the power liftgate.
Page 38 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE When the remote button is pressed the “Lamp Flash” feature is enabled the tail lights will flash to signal that the liftgate is opening or closing. A beeping signal will sound two seconds before the liftgate starts to open or close.
Page 39 • The power liftgate switches will not operate if the vehicle is in gear or the vehicle speed is above 0 mph (0 km/h). • The power liftgate will not operate in temperatures below 12° F ( 24° C) or temperatures above 143° F (62°...
Page 40: Occupant Restraints
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems. These include the front and rear seat belts for the driver and all passengers, front airbags for both the driver and front passenger, and if equipped, left and right window bags for the driver and passengers seated next to a window and a driver inflat- able knee blocker.
Page 41: Lap/Shoulder Belts
Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passengers as safe as possible. WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buck- led up.
Page 42 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. •...
Page 43 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is near the seatback of the front seats and next to your arm in the rear seats. Grasp the latch plate and pull out the belt.
Page 44 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click”. Latch Plate To Buckle WARNING! • A belt that is buckled into the wrong buckle will not protect you properly.
Page 45 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision.
Page 46 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system.
Page 47: Lap/Shoulder Belt Untwisting Procedure
Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180°...
Page 48: Enhanced Seat Belt Use Reminder System (Beltalert) - Driver Front Seat Only
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Seat Belt Use Reminder System (BeltAlert) — Driver Front Seat Only If the occupied driver’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced Warning System (BeltAlert) will alert the driver to buckle their seat belt.
Page 49: Seat Belts And Pregnant Women
3. Within 60 seconds of turning the ignition switch to the ON/RUN position, unbuckle and then re-buckle the driver’s seat belt at least three times within 10 seconds, ending with the seat belt buckled. NOTE: Watch for the Seat Belt Warning Light to turn on while unbuckling and off while re-buckling the seat belt.
Page 50: Driver And Front Passenger Supplemental Restraint System - Airbag
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions.
Page 51 Also, the front passenger airbag is certified to the Federal regulations that define Occupant Classification (Refer to “Occupant Classification System” in this section). This vehicle may also be equipped with a driver inflat- able knee blocker located on the instrument panel below the steering column.
Page 52 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not put anything on or around the airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protec- tive covers for the airbag cushions are designed to open only when the airbags are inflating.
Page 53 If your vehicle is equipped, the window bag on the crash side of the vehicle is triggered in moderate to severe side collisions. But even in collisions where the airbags inflate, you need the seat belts to keep you in the right position for the airbags to protect you properly.
Page 54 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE You should read the instructions provided with your child restraint to make sure that you are using it properly. 2. All occupants should wear their lap and shoulder belts properly. 3. The driver and front passenger seats should be moved back as far as practical to allow the front airbags room to inflate.
Page 55 Airbag System Components The airbag system consists of the following: • Occupant Restraint Controller (ORC) • AIRBAG Light • Driver Airbag • Front Passenger Airbag • Supplemental Side Curtain Airbags (If Equipped) • Front Impact Sensors • Side Impact Sensors (If Equipped) •...
Page 56 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How The Airbag System Works • The Occupant Restraint Controller (ORC) determines if a frontal collision is severe enough to require the airbags to inflate. Based on the level of collision severity, the front control module determines the proper rate of inflation.
Page 57 WARNING! Ignoring the AIRBAG warning light in your instru- ment panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away.
Page 58 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE about 30 milliseconds (about one quarter of the time it takes to blink your eyes) with enough force to injure you if you are not belted and seated properly, or if items are positioned in the area where the window bag inflates.
Page 59 If there is a rapid change in temperature or humidity, the OCS may not be able to properly approximate occupant size. If your seat including your trim cover and cushion needs to be serviced in any way (includ- ing removal or loosening/tightening of seat attach- ment bolts), take the vehicle to your authorized dealer.
Page 60 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE For almost all sizes of properly seated adults, the airbag will be enabled in the event of a collision. For small teenagers and some small adults, depending on size, the airbag may or may not be enabled in the event of a collision.
Page 61 • The Passenger Airbag Disabled (PAD) Indicator Light indicates to the driver and passenger when the airbag is turned OFF in the presence of a properly seated occupant. When the PAD indicator light is illuminated, the airbag is OFF. Also, when the Occu- pant Classification System (OCS) detects either an empty seat of a weight less than the predetermined occupant threshold, the ORC will not illuminate the...
Page 62 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Unapproved modifications or service procedures to the front passenger seat assembly, its related compo- nents, or seat cover may inadvertently change the airbag deployment in case of a frontal crash. This could result in death or serious injury to the front seat passenger if the vehicle is involved in an acci- dent.
Page 63 If A Deployment Occurs The airbag system is designed to deploy the airbags when the ORC and impact sensors detect a moderate-to- severe collision, to help restrain the vehicle passengers, and then immediately deflate. NOTE: A collision that is not severe enough to need airbag protection will not activate the system.
Page 64 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Deployed airbags, front seat belt buckle pretension- ers and driver inflatable knee blocker cannot protect you in another collision. Have the airbags, front seat belt buckle pretensioners and driver inflatable knee blocker replaced by an authorized dealer as soon as possible.
Page 65: Event Data Recorder (Edr)
WARNING! • You need proper knee impact protection in a collision. Do not mount or locate any aftermarket equipment on or behind the knee bolsters. • It is dangerous to try to repair any part of the airbag system yourself. Be sure to tell anyone who works on your vehicle that it has airbags.
Page 66 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE data gathered during a complete accident investigation, the electronic data may be used by DaimlerChrysler Corporation and others to learn more about the possible causes of crashes and associated injuries in order to assess and improve vehicle performance.
Page 67: Child Restraint
Data Parameters that May Be Recorded: • Diagnostic trouble code(s) and warning lamp status for electronically-controlled safety systems, including the airbag system • Airbag disable lamp status (if equipped) • Time of airbag deployment (in terms of ignition cycles and vehicle mileage) •...
Page 68 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.
Page 69 • Rearward-facing child seats must NEVER be used in the front seat of a vehicle with a front passenger airbag. An airbag deployment could cause severe injury or death to infants in this position. Older Children and Child Restraints Children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle.
Page 70 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE and use the lap belt. Never allow a child to put the shoulder belt under an arm or behind their back. NOTE: additional information, www.seatcheck.org or call 1-866-SEATCHECK. WARNING! • Improper installation can lead to failure of an infant or child restraint.
Page 71 shoulder portion of the lap/shoulder belt will tighten the belt. The cinching latch plate will keep the belt tight, however, any seat belt system will loosen with time, so check the belt occasionally and pull it tight if necessary. • In the rear seat, you may have trouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path opening on the restraint.
Page 72 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Six passenger vehicles are equipped with second row fold & tumble seats with lower anchorages that can accommodate rigid mount or flexible webbing-mounted LATCH-compatible child seats. The third row seating positions are not equipped with lower anchorages. How- ever, the third row driver side seating position is equipped with a tether anchor.
Page 73 Five passenger vehicles are equipped with a second row bench seat only. The two outboard seating positions have lower anchorages that can accommodate rigid mount or flexible webbing-mounted LATCH-compatible child seats. The center seating position of the bench seat can also accommodate a flexible webbing-mounted LATCH- compatible child seat by using the inboard lower anchors of the two outboard seating positions.
Page 74 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE convenient. When using the LATCH System, always follow the child restraint manufacturer’s installation in- structions. NOTE: If your child restraint seat is not LATCH com- patible, install the restraint using the vehicle seat belts. Tether Anchors There are tether strap anchorages behind all second row seating positions and for six passenger vehicles on the...
Page 75 When the tether anchorage is used in the center second row bench seating position or on the third row seating position, where equipped, the strap should be positioned straight over the top of the seatback. Bench Seat Tether Strap Routing THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 When the tether anchorage is used in the third row seating position, the strap should be positioned straight...
Page 76 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap.
Page 77 anchorages. Then tighten all three straps as you push the child restraint rearward and downward into the seat. Child restraint systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the seatback tether anchorage have been available for some time.
Page 78 78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
Page 79: Engine Break-In Recommendations
ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the engine in your new vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle acceleration, within the limits of local traffic laws, contributes to a good break-in.
Page 80: Safety Checks You Should Make Inside The Vehicle
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed. WARNING! If you are required to drive with the deck lid/liftgate open, make sure that all windows are closed, and the...
Page 81: Periodic Safety Checks You Should Make Outside The Vehicle
Periodic Safety Checks You Should Make Outside The Vehicle Tires Examine tires for excessive tread wear or uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect tread and sidewall for cuts or cracks. Check wheel nuts for tightness, and tires (includ- ing spare) for proper pressure.
Page 83: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors .......88 Inside Day / Night Mirror ....88 Automatic Dimming Mirror —...
Page 84 84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Seats ....... . 114 10–Way Driver’s Power Seat —...
Page 85 Headlights, Parking Lights, Instrument Panel Lights ......135 Automatic Headlights ....136 Daytime Running Lights (Canada Only) .
Page 86 86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Resume Speed ..... 151 To Vary The Speed Setting ....151 To Accelerate For Passing .
Page 87 Storage ......166 Console Features ..... . 166 Rear Cargo Storage Bin —...
Page 88: Mirrors
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day / Night Mirror Adjust the mirror to center on the view through the rear window. A two point pivot system allows for horizontal and vertical adjustment of the mirror. MANUAL REARVIEW MIRROR Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle).
Page 89: Driver's Side Outside Mirror Auto Dimmer - If Equipped
Automatic Dimming Mirror CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 Driver’s Side Outside Mirror Auto Dimmer —...
Page 90: Outside Mirror - Passenger's Side
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirror — Passenger’s Side Adjust the convex outside mirror so you can just see the side of your vehicle in the portion of the mirror closest to the vehicle. This type of mirror will give a much wider view to the rear, and especially of the lane next to your vehicle.
Page 91: Heated Remote Control Mirrors
UConnect™ system. NOTE: The UConnect™ system use requires a cellular phone equipped with the Bluetooth Hands-Free Profile, version 0.96 or higher. See www.chrysler.com/uconnect for supported phones.
Page 92 92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE UConnect™ allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle, and enables you to mute the system’s micro- phone for private conversation. The UConnect™ phonebook enables you to store up to 32 names and four numbers per name.
Page 93: Operations
The UConnect™ system can be used with any Hands- Free Profile certified Bluetooth™ cellular phone. See www.chrysler.com/uconnect for supported phones. If your cellular phone supports a different profile (e.g., Headset Profile), you may not be able to use any UCon- nect™...
Page 94 Bluetooth™ enabled cellular phone. NOTE: The UConnect™ system use requires a cellular phone equipped with the Bluetooth Hands-Free Profile, version 0.96 or higher. See www.chrysler.com/uconnect for supported phones. To complete the pairing process, you will need to refer- ence your cellular phone owner’s manual.
Page 95 NOTE: • www.chrysler.com/uconnect • www.dodge.com/uconnect • www.jeep.com/uconnect The following are general phone to UConnect™ System pairing instructions: • Press the ’Phone’ button to begin. • After the Ready prompt and the following beep, say Setup Phone Pairing and follow the audible prompts.
Page 96 96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Call/Dial by Saying a Number • Press the ’Phone’ button to begin. • After the Ready prompt and the following beep, say Dial. • System will prompt you to say the number you want call.
Page 97 • After the Ready prompt and the following beep, say Phonebook New Entry. • When prompted, say the name of the new entry. Use of long names helps the voice recognition and is recom- mended. For example, say Robert Smith or Robert instead of Bob.
Page 98 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When prompted, recite the new phone number for the phonebook entry that you are editing. After you are finished editing an entry in the phonebook, you will be given the opportunities to edit another entry in the phonebook, call the number you just edited, or return to the main menu.
Page 99: Phone Call Features
After confirmation, the phonebook entries will be de- leted. Note that only the phonebook in the current language is deleted. Delete All Entries in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the Ready prompt and the following beep, say Phonebook Erase All.
Page 100 100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Answer or Reject an Incoming Call - No Call Currently in Progress When you receive a call on your cellular phone, the UConnect™ system will interrupt the vehicle audio system, if on, and will ask if you would like to answer the call.
Page 101 Toggling Between Calls If two calls are in progress (one active and one on hold), press the ’Phone’ button until you hear a single beep indicating that the active and hold status of the two calls have switched. Only one call can be placed on hold at one time.
Page 102: Uconnect™ System Features
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Call Continuation Call continuation is progression of a phone call on UConnect™ system after the vehicle ignition key has been switched to off. Call continuation functionality available on the vehicle can be any one of three types: •...
Page 103 Emergency Assistance If you are in an emergency and the mobile phone is reachable: • Pick up the phone and manually dial the emergency number for your area. If the phone is not reachable and the UConnect™ system is operational, you may reach the emergency number as follows: •...
Page 104 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Please refer to the 24-Hour “Towing Assistance” cover- age details in the Warranty information booklet and on the 24–Hour Towing Assistance Card. Paging To learn how to page, refer to Working with Automated Systems.
Page 105 Barge In - Overriding Prompts The ’Voice Recognition’ button can be used when you wish to skip part of a prompt and issue your voice recognition command immediately. For example, if a prompt is playing Would you like to pair a phone, clear a , you could press the ’Voice Recognition’...
Page 106: Advanced Phone Connectivity
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Certain brands of mobile phones do not send the dial ring to the UConnect™ system to play it on the vehicle audio system, so you will not hear it. Under this situation, after successfully dialing a number, the user may feel that the call did not go through even though the call is in progress.
Page 107 Connect or Disconnect Link Between the UConnect™ System and Cellular Phone Your cellular phone can be paired with many different electronic devices, but can only be actively connected with one electronic device at a time. If you would like to connect or disconnect the Blue- tooth™...
Page 108: Things You Should Know About Your Uconnect™ System
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • You can also press the Voice Recognition’ button anytime while the list is being played, and then choose the phone that you wish to select. • The selected phone will be used for the next phone call.
Page 109 • low road noise, • smooth road surface, • fully closed windows, • dry weather condition. • Even though the system is designed for users speaking in North American English, French, and Spanish ac- cents, the system may not always work for some. •...
Page 110 110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • fully closed windows, and • dry weather condition. • Operation from driver seat. • Performance, such as audio clarity, echo, and loudness to a large degree rely on the phone and network, and not the UConnect™...
Page 111 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111...
Page 112 112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 113 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113...
Page 114: Seats
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE North American English Primary Alternate(s) Zero Add location Add new All of them Confirmation prompts Confirmations prompts Delete a name Delete Language Select language List names List all List paired phones List phones Pager Beeper Phone pairing...
Page 115: 8-Way Driver's Power Seat - If Equipped
WARNING! Adjust the seat only while the vehicle is parked. Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. 8–Way Driver’s Power Seat —...
Page 116: Heated Seats - If Equipped
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE restraint. To lower the head restraint, depress the release tab located at the base of the head restraint and push down on the head restraint. Adjustable Head Restraints Heated Seats — If Equipped This feature heats the driver, front passenger and second row seats.
Page 117 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 Press the switch once to select a heat setting (high or low) and press the switch a second time in the same direction to turn the heated seat off. The indicator light will show when LOW or HIGH heat is ON.
Page 118: Second Row Manual Seat Recliner - If Equipped
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • If the lights in the second row heated seat switch begin to flash when the switch is pressed, it indicates that the heated seat is not functioning properly and that ser- vice is required.
Page 119: Second Row Manual Seat Adjuster - If Equipped
WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or fatally injured. Use the recliner only when the vehicle is parked.
Page 120: Second Row Bench Seating - If Equipped
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Adjust the seat only while the vehicle is parked. Adjusting a seat while the vehicle is moving is dangerous. The seat belt might not be properly adjusted and you could be injured. Second Row Bench Seating —...
Page 121: Second Row Fold & Tumble Seats - If Equipped
CAUTION! Be sure there is nothing in front of the second row seat cushion before folding it down. Damage to the seat may occur. Second Row Fold & Tumble Seats — If Equipped The second row seats can be folded and tumbled forward for easy access to the third seat or rear cargo area.
Page 122: Third Row Easy Exit - If Equipped
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Pull up on the release handle labeled “2” and lift firmly to tumble the seat fully forward. If the seat contacts the rear of the front seat, move the front seat forward. Seat Release Handle To relatch the seat, tilt the seat rearward and push down firmly to engage the rear attachments.
Page 123 To fold and tumble the seat forward, follow these steps: 1. Pull up on the seatback release handle “1” located on the back of the seat to fold the seatback down. Release Handle 1 Location 2. Pull the release strap “2” located at the bottom of the seat to lift and tumble the seat forward.
Page 124: Third Row Seating - If Equipped
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Third Row Seating — If Equipped The third row seats may be used with either or both seatbacks folded forward for additional storage space. To fold the seat, remove any objects from in front of or on the seat.
Page 125: Load Floor - If Equipped
WARNING! • Not all head restraints in this vehicle are the same. Head restraints from one seating position should not be removed and installed in any other seating position. In a collision, serious injury or death may result if the proper head restraint is not installed on each seat.
Page 126: Plastic Grocery Bag Retainer
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Pull on the load floor strap and lift the panel from the driver’s second row seatback over the center console and onto the passenger second row seat. Load Floor Panel NOTE: Be sure to reattach the strap to secure the load floor panel when not in use.
Page 127: Driver Memory Seat - If Equipped
DRIVER MEMORY SEAT — IF EQUIPPED If your vehicle is equipped with memory systems, your remote keyless entry transmitter or memory seat buttons on the driver’s door panel can be used to recall the driver’s seat, outside mirrors, adjustable pedals (if equipped) and radio station presets to saved positions.
Page 128 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Your vehicle has been delivered with two remote keyless entry transmitters. One or both transmitters can be linked to either memory position. Up to eight remote keyless entry transmitters can be used with your vehicle. The memory seat system can also accommodate up to eight transmitters linked to either of the two stored seat positions or any combination of the two positions.
Page 129 Repeat the above steps for the second position using the other driver’s door numbered button and Remote Key- less Entry Transmitter. Each time the SET (S) button and a numbered button are pressed, you erase the old memory and store a new one. To Disable A Transmitter Link, Follow These Steps: 1.
Page 130: Easy Exit Seat (Available With Memory Seat Only)
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Easy Exit Seat (Available with Memory Seat Only) This feature provides automatic driver’s seat positioning which will enhance driver mobility out of and into the vehicle. There are two possible Easy Exit and Easy Entry adjust- ments available: •...
Page 131: Tilt Mirrors In Reverse (Available With Memory Seat Only) - If Equipped
Tilt Mirrors in Reverse (Available with Memory Seat Only) — If Equipped This additional feature provides automatic outside mir- ror positioning which will aid the driver’s view of the ground rearward of the front doors. The outside mirrors will move slightly downward from the present position when the vehicle is shifted into the Reverse position.
Page 132 132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Next, push to the left the safety catch located under the front edge of the hood, near the center. Hood Safety Catch Use the hood prop rod to secure the hood in the open position.
Page 133: Lights
LIGHTS Overhead Console Map/Reading Lights These lights are mounted between the sun visors on the overhead console. Each light is turned ON by pressing the lens. Press the lens a second time to turn the light OFF. The lights also turn on when a door is opened or the dimmer control is turned fully upward, past the second detent.
Page 134: Interior Lights
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior Lights The interior lights come on when a door is opened. The interior lights will automatically turn off in about 15 minutes if a door is left open or the dimmer control is left in the Dome light position.
Page 135: Headlights, Parking Lights, Instrument Panel
Headlights, Parking Lights, Instrument Panel Lights Turn the end of the Multi-Function Lever to the first detent for parking light and instrument panel light operation. Turn to the second detent for headlight, park light and instrument panel light operation. To change the brightness of the instrument panel lights, rotate the center portion of the Multi-Function Lever up or down.
Page 136: Automatic Headlights
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Parade Mode (Daytime Brightness Feature) Rotate the dimmer control upward to the first detent. This feature brightens the odometer and radio display when the parking lights or headlights are on during daylight conditions. Automatic Headlights This system automatically turns your headlights ON or OFF based on ambient light levels.
Page 137: Fog Lights - If Equipped
To activate the delay feature, turn off the ignition switch while the headlights are still on. Then turn off the headlights within 45 seconds. The 90 second delay inter- val begins when headlight switch is turned off. If the headlights or park lights are turned back on or the ignition switch is turned on, the delay will be cancelled.
Page 138: Highbeam/Lowbeam Select Switch
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Highbeam/Lowbeam Select Switch Pull the Multi-Function Lever towards you to switch the headlights to HIGH beam. Pull the Lever a second time to switch the headlights to LOW beam. Passing Light You can signal another vehicle with your headlights by lightly pulling the Multi-Function Lever toward you.
Page 139: Mist Feature
If the lever is pulled while in the OFF position, the wipers will operate for two wipe cycles, then turn OFF. Mist Feature Push down on the wiper lever to activate a single wipe to clear off road mist or spray from a passing vehicle. As long as the lever is held down, the wipers will continue to operate.
Page 140 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rotating the center of the switch up to the DEL (Delay) position or the ON position will activate the rear wiper. Push the lever forward to initiate the rear wash function in any of the three positions. The washer pump will continue to operate as long as the lever is pressed.
Page 141: Tilt Steering Column
TILT STEERING COLUMN To tilt the column, pull the lever, located behind the turn signal control, toward you and move the steering wheel up or down, as desired. Release the lever to lock the steering wheel firmly in place. Tilt Steering Column Control UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 WARNING! Tilting the steering column while the vehicle is...
Page 142 142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE spinning faster than the other, the system will apply the brake of the spinning wheel. This will allow more engine torque to be applied to the wheel that is not spinning. This feature remains active even if TCS and ESP are in either the “Partial Off”...
Page 143: Rear Park Assist System - If Equipped
NOTE: • The Traction Control Indicator comes on each time the ignition switch is turned ON. This will occur even if you used the switch to turn the system OFF. • The Traction Control system will make buzzing or clicking sounds when in operation. REAR PARK ASSIST SYSTEM —...
Page 144 144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The system dimly illuminates the two outer most yellow LEDs when it is ON and detecting no obstacles. The following chart shows the warning display operation when the system is detecting an obstacle: WARNING DISPLAY DISTANCES DISPLAY LED OBSTACLE DISTANCE FROM:...
Page 145 WARNING! • Drivers must be careful when backing up even when using the Rear Park Assist System. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up. You are responsible for the safety of your surroundings and must continue to pay attention while backing up.
Page 146: Rear Camera - If Equipped
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • Ensure that the rear bumper is free of dirt and debris to keep the system operating properly. • Jackhammers, large trucks, and other vibrations could affect the performance of the system. If “Service Park Assist System”...
Page 147 WARNING! Drivers must be careful when backing up even when using the Rear Camera System. Always check care- fully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up. You are responsible for the safety of your surroundings and must con- tinue to pay attention while backing up.
Page 148: Adjustable Pedals - If Equipped
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ADJUSTABLE PEDALS — IF EQUIPPED This feature allows both the brake and accelerator pedals to move toward or away from the driver to provide improved position with the steering wheel. The adjust- able pedal system is designed to allow a greater range of driver comfort for steering wheel tilt and seat position.
Page 149 Press the switch rearward to move the pedals rearward (toward the driver). • The pedals can be adjusted with the ignition OFF. • The pedals can be adjusted while driving. • The pedals cannot be adjusted when the vehicle is in R (Reverse) or when the Speed Control is ON.
Page 150: Electronic Speed Control
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRONIC SPEED CONTROL When engaged, this device takes over the accelerator operation at speeds greater than 30 mph (50 km/h). The speed control switches are located on the steering wheel. Speed Control Switches To Activate: Push the “ON/OFF”...
Page 151: To Set At A Desired Speed
To Set At A Desired Speed: When the vehicle has reached the desired speed, press and release the “SET” button. Release the accelerator and the vehicle will operate at the selected speed. The CRUISE SET indicator located near the instrument clus- ter odometer will illuminate showing the electronic speed control is set.
Page 152: To Accelerate For Passing
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Tapping the “COAST” button once will result in a 1 mph (2 km/h) speed decrease. Each time the button is tapped, speed decreases. To Accelerate For Passing: Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed.
Page 153: Overhead Console - If Equipped
OVERHEAD CONSOLE — IF EQUIPPED The overhead console can contain courtesy/reading lights, an optional universal garage door opener (HomeLink ), storage for sunglasses, optional power sunroof switches and an optional power liftgate switch. Overhead Console UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 Courtesy/Reading Lights At the forward end of the console are two courtesy/ reading lights.
Page 154: Garage Door Opener - If Equipped
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE GARAGE DOOR OPENER — IF EQUIPPED The HomeLink Universal Transceiver replaces up to three remote controls (hand held transmitters) that oper- ate devices such as garage door openers, motorized gates, or home lighting. It triggers these devices at the push of a button.
Page 155: Programming Homelink
WARNING! Vehicle exhaust contains carbon monoxide, a danger- ous gas. Do not run the vehicle’s exhaust while training the transceiver. Exhaust gas can cause seri- ous injury or death. WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate.
Page 156 156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE seconds and do not repeat Step One to program a second and/or third hand-held transmitter to the remaining two HomeLink buttons. Homelink Buttons 2. Position the end of your hand-held transmitter 1-3 inches (3-8 cm) away from the HomeLink buttons while keeping the indicator light in view.
Page 157 5. Press and hold the just trained HomeLink button and observe the indicator light or the EVIC display. If the indicator light stays on constantly, programming is complete and your device should activate when the HomeLink button is pressed and released. If the EVIC display shows “Channel X Transmit”...
Page 158: Canadian Programming/Gate Programming
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Return to the vehicle and firmly press, hold for two seconds and release the programmed HomeLink button. Repeat the press/hold/release sequence a second time, and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming.
Page 159: Using Homelink
Using HomeLink To operate, simply press and release the programmed HomeLink button. Activation will now occur for the trained device (i.e. garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.). For convenience, the hand-held transmitter of the device may also be used at any time.
Page 160: Security
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Security If you sell your vehicle, be sure to erase the frequencies by following the “Erasing HomeLink Buttons” instruc- tions in this section. This device complies with part 15 of FCC rules and with RSS-210 of Industry Canada.
Page 161: Express Open Feature
Press and hold the “OPEN” button rearward to fully open the sunroof. The sunroof can be stopped at any position between closed and full open. Momentarily pressing the “OPEN” button rearward will activate the Express Open Feature, causing the sunroof to open automatically.
Page 162 162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To close the sunroof, press and hold the “CLOSE” button forward. Again, any release of the button will stop the movement and the sunroof will remain in a partial open condition until the button is pushed forward again. The sunshade can be opened manually.
Page 163: Wind Buffeting
Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.
Page 164: Electrical Outlet Use With Engine Off
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE A third outlet is located on the back of the front center console near the floor, and is also controlled by the ignition switch. A fourth outlet is located on the driver’s side, in the rear cargo area and is also controlled by the ignition switch.
Page 165: Cupholders
CUPHOLDERS Front Seat Cupholders The cupholders are located in the forward edge of the center console. Push down on the forward edge of the console to release the cupholders. Press the cover up when the cupholders are no longer needed. Six Passenger Seating Cupholders UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 Second Row Seat Cupholders...
Page 166: Third Row Seat Cupholders - If Equipped
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE On vehicles equipped with six passenger seating the second row seat cupholders are located in the forward edge of the center console located between the second row seats. Push down on the forward edge of the console to release the cupholders.
Page 167: Retractable Cargo Area Cover - If Equipped
Retractable Cargo Area Cover — If Equipped To cover the cargo area: 1. Fold down the third row seatbacks. 2. Unfold the cargo cover extensions and lock into place. 3. Insert the pins on the ends of the cover into the slots located on the trim panel behind the second row seat- backs.
Page 168: Cargo Tie-Down Hooks
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Insert the pins on the ends of the cover into the slots located on the trim panel behind the third row seatbacks. 4. Grasp the center portion of the cover flap. Pull it over the cargo area.
Page 169: Roof Luggage Rack - If Equipped
• Place as much cargo as possible in front of the rear axle. Too much weight or improperly placed weight over or behind the rear axle can cause the rear of the vehicle to sway. • Do not pile luggage or cargo higher than the top of the seatback.
Page 170 170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Distribute cargo weight evenly on the roof rack crossbars. The roof rack does not increase the total load carrying capacity of the vehicle. Be sure the total load of cargo inside the vehicle plus that on the external rack does not exceed the maximum vehicle load capacity.
Page 171 CAUTION! • Crossbars should remain equally spaced or parallel at any luggage rack position for proper function. Non- compliance could result in damage to the luggage rack, cargo and/or vehicle. • To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lbs (68 kg).
Page 172: Load Leveling System
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LOAD LEVELING SYSTEM The automatic load leveling system will provide a level riding vehicle under most passenger and cargo loading conditions. A hydraulic pump contained within the shock absorbers raises the rear of the vehicle to the correct height. It takes approximately 1 mile (1.6 km) of driving for the leveling to complete depending on road surface conditions.
Page 173: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instrument Panel And Controls ... . . 177 Base Instrument Cluster ....178 Premium Instrument Cluster .
Page 174 174 UNDERSTANDING YOUR INSTRUMENT PANEL Sales Code RAH—AM & FM Stereo Radio With CD Player And CD/DVD Changer Controls ..202 Radio Operation ..... . 202 CD Player Operation .
Page 175 Satellite Radio — If Equipped ....233 System Activation ..... 234 Electronic Serial Number/Sirius Identification Number (ENS/SID) .
Page 176 176 UNDERSTANDING YOUR INSTRUMENT PANEL Manual Air Conditioning Operation ..246 Electric Rear Window Defroster ... 259 Dual-Zone Automatic Temperature Control . . . 249...
Page 177: Instrument Panel And Controls
UNDERSTANDING YOUR INSTRUMENT PANEL 177 INSTRUMENT PANEL AND CONTROLS...
Page 178: Base Instrument Cluster
178 UNDERSTANDING YOUR INSTRUMENT PANEL BASE INSTRUMENT CLUSTER...
Page 179: Premium Instrument Cluster
UNDERSTANDING YOUR INSTRUMENT PANEL 179 PREMIUM INSTRUMENT CLUSTER...
Page 180: Instrument Cluster Descriptions
180 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 1. Voltage Light This light monitors the electrical system voltage. The light should turn on momentarily as the engine is started. If the light stays on or turns on while driving, it indicates a problem with the charging system. Immediate service should be obtained.
Page 181 WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, see Section 7 of this manual. Follow the warnings under the Cooling System Pressure Cap paragraph.
Page 182 182 UNDERSTANDING YOUR INSTRUMENT PANEL is not functioning and that service is required. However, the conventional brake system will continue to operate normally if the BRAKE warning light is not on. If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock brakes.
Page 183 Vehicles equipped with Anti-Lock brakes (ABS), are also equipped with Electronic Brake Force Distribution (EBD). In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light. Immediate repair to the ABS system is required. The operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON position.
Page 184 184 UNDERSTANDING YOUR INSTRUMENT PANEL disabled for about 4 minutes until the brakes have cooled. The system will automatically reactivate and turn off the Traction Control Light. 9. Tachometer The red segments indicate the maximum permissible engine revolutions-per-minute (rpm. x 1000) for each gear range.
Page 185 Loose Fuel Filler Cap If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, GASCAP will be displayed in the instrument cluster odometer. Tighten the fuel filler cap properly and press the odometer reset button to turn the GASCAP message off.
Page 186: Understanding Your Instrument Panel 173
186 UNDERSTANDING YOUR INSTRUMENT PANEL 17. Navigation Screen / Rear View Camera — If Equipped The navigation system provides maps, turn identifica- tion, selection menus and instructions for selecting a variety of destinations and routes. Refer to your “Navi- gation User’s Manual” for detailed operating instruc- tions.
Page 187 21. Tire Pressure Monitoring Telltale Lamp — If Equipped Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those...
Page 188 188 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! The Tire Pressure Monitoring System (TPMS) has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your ve- hicle. Undesirable system operation or sensor dam- age may result when using replacement equipment that is not of the same size, type, and / or style.
Page 189 25. Liftgate Ajar — If Equipped This light turns on if the liftgate is not com- pletely closed. 26. Door Ajar Light — If Equipped This light turns on if a door is not completely closed. 27. Washer Fluid Light — If Equipped This light turns on when the washer fluid level falls below approximately 1/4 filled.
Page 190 190 UNDERSTANDING YOUR INSTRUMENT PANEL — The ESP Control System will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when ESP becomes inactive following the maneuver that caused the ESP activation. 29. Electronic Throttle Control (ETC.) Light This light informs you of a problem with the Electronic Throttle Control system.
Page 191: Electronic Vehicle Information Center (Evic) - If Equipped
ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) — IF EQUIPPED The Electronic Vehicle Information Center (EVIC) con- sists of the following: • Vehicle information warning message displays • Tire Pressure Monitor System — If Equipped • Customer programmable features • Compass display •...
Page 192 192 UNDERSTANDING YOUR INSTRUMENT PANEL • SET INHIBITED DUE TO MOTION (with a single chime) • FOB LINKED (with a single chime) • FOB UNLINKED (with a single chime) • PARK BRAKE ENGAGED (with a single chime) • LOW BRAKE FLUID (with a single chime) •...
Page 193: Customer Programmable Features - If Equipped
• CLEARING CHANNELS • CHANNELS CLEARED • CHANNELS DEFAULTED • DID NOT TRAIN • 1,2,3 OR 4 TIRE(S) LOW PRESSURE (Refer to ”Tire Pressure Monitor System” in the “Starting And Oper- ating, Tire Section”) • CHECK TPM SYSTEM (Refer to ”Tire Pressure Monitor System”...
Page 194 194 UNDERSTANDING YOUR INSTRUMENT PANEL Display U.S. or Metric? Pressing the US/M button will change the EVIC, odom- eter, navigation system and A/C Control units from US to Metric. Use factory Settings? When in this display you may select to use the factory settings and no programmable features will be offered.
Page 195 Sound Horn On Lock? When this feature is selected a short horn sound will occur when the remote keyless entry “Lock” button is pressed. This feature may be selected with or without the flash lights on lock/unlock feature. Pressing the STEP button when in this display will select “Yes”...
Page 196 196 UNDERSTANDING YOUR INSTRUMENT PANEL Reset Service Distance (Displays Only if Service Interval was Changed) When this feature is selected the current accumulated service distance can be reset to the newly selected service interval. Pressing the STEP button when in this display will select “Yes”...
Page 197: Compass Display - If Equipped
Compass Display — If Equipped This display provides one of eight compass readings to indicate the direction the vehicle is facing. Automatic Compass Calibration This compass is self calibrating which eliminates the need to manually set the compass. When the vehicle is new, the compass may appear erratic and the EVIC will display “COMPASS CALIBRATING”...
Page 198 198 UNDERSTANDING YOUR INSTRUMENT PANEL Compass Variance Compass Variance is the difference between magnetic North and Geographic North. In some areas of the country, the difference between magnetic and geographic North is great enough to cause the compass to give false readings.
Page 199: Mini-Trip Functions - If Equipped
To set the variance: Turn the ignition switch ON and set the display to Compass. Press the MENU button for approximately 5 seconds but no more than 10 seconds. The “COMPASS VARIANCE” message and the last vari- ance zone number will be displayed. Press the STEP button to select the proper variance zone as shown in the map.
Page 200: Electronic Digital Clock
200 UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC DIGITAL CLOCK The clock and radio each use the display panel built into the radio. A digital readout shows the time in hours and minutes whenever the ignition switch is in the ON or ACC position and the time button is pressed.
Page 201: Electrical Disturbances
Electrical Disturbances Radio waves may pick up electrical disturbances during transmission. They mainly affect the wave amplitude, and thus remain a part of the AM reception. They interfere very little with the frequency variations that carry the FM signal. AM Reception AM sound is based on wave amplitude, so AM reception can be disrupted by such things as lightning, power lines and neon signs.
Page 202: Sales Code Rah-Am & Fm Stereo Radio With Cd Player And Cd/Dvd Changer Controls
202 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RAH—AM & FM STEREO RADIO WITH CD PLAYER AND CD/DVD CHANGER CONTROLS NOTE: The radio sales code is located on the lower left side of your radio faceplate. RAH radio Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on.
Page 203 Toggle the TUNE button to select the following format types: Program Type Radio Display Adult Hits Adult Hit Classical Classical Classic Rock Classic Rock College College Country Country Information Inform Jazz Jazz Foreign Language Language News News Nostalgia Nostalgia Oldies Oldies Personality Personality...
Page 204 204 UNDERSTANDING YOUR INSTRUMENT PANEL The radio display will flash “SEEK” and the selected PTY program type when searching for the next PTY station. If no station is found with the selected PTY program type, the radio will return to the last preset station. If a preset button is activated while in the PTY (Program Type) mode, the PTY mode will be exited and the radio will tune to the preset station.
Page 205 Tone Control The Bass and/or Treble controls sound for the desired tone. Press the AUDIO button, select Bass or TREBLE, then press SEEK + or SEEK to increase or decrease amplification of the band. To Set The Radio Push-Button Memory When you are receiving a station that you wish to commit to push-button memory, press the SET button.
Page 206: Cd Player Operation
206 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Changes or modifications not expressively ap- proved by the party responsible for compliance could void the user’s authority to operate the equipment. CD Player Operation NOTE: • The ignition switch must be in the ON or ACC position and the volume control ON before the CD player will operate.
Page 207 Seek Press the top of the SEEK button for the next selection on the CD. Press the bottom of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first 10 seconds of the current selection.
Page 208: Cd/Dvd Changer Operation
208 UNDERSTANDING YOUR INSTRUMENT PANEL CD/DVD Changer Operation Press the MODE button to select between the CD player and the optional remote CD/DVD changer. Time Press the TIME button to change the display from elapsed CD or DVD playing time to time of day. Notes On Playing MP3 Files The radio can play MP3 files, however, acceptable MP3 file recording media and formats are limited.
Page 209 CD audio tracks and computer files (including MP3 files). Discs created with an option such as keep disc open after writing are most likely multisession discs. The use of multisession for CD audio or MP3 playback may result in longer disc loading times. Supported MP3 file formats The radio will recognize only files with the *.mp3 exten- sion as MP3 files.
Page 210: Operation Instructions
210 UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3 files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
Page 211 RW/FF (CD Mode For MP3 Play) Press the FF side of the button to move forward through the MP3 selection. Press the RW side of the button to move back through the MP3 selection. AM/FM Button (CD Mode For MP3 Play) Switches back to Radio mode.
Page 212: Sales Code Rev Am & Fm Stereo Radio With Cd Player And Cd/Dvd Changer Controls
212 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE REV AM & FM STEREO RADIO WITH CD PLAYER AND CD/DVD CHANGER CONTROLS NOTE: The radio sales code is located on the lower left side of your radio faceplate. REV Radio Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on.
Page 213 Toggle the TUNE button to select the following format types: Program Type Radio Display Adult Hits Adult Hit Classical Classical Classic Rock Classic Rock College College Country Country Information Inform Jazz Jazz Foreign Language Language News News Nostalgia Nostalgia Oldies Oldies Personality Personality...
Page 214 214 UNDERSTANDING YOUR INSTRUMENT PANEL The radio display will flash “SEEK” and the selected PTY program type when searching for the next PTY station. If no station is found with the selected PTY program type, the radio will return to the last preset station. If a preset button is activated while in the PTY (Program Type) mode, the PTY mode will be exited and the radio will tune to the preset station.
Page 215 Tone Control The Bass and/or Treble controls sound for the desired tone. Press the AUDIO button, select Bass or TREBLE, then press SEEK + or SEEK to increase or decrease amplification of the band. To Set The Radio Push-Button Memory When you are receiving a station that you wish to commit to push-button memory, press the SET button.
Page 216: Cd Player Operation
216 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Changes or modifications not expressively ap- proved by the party responsible for compliance could void the user’s authority to operate the equipment. CD Player Operation NOTE: • The ignition switch must be in the ON or ACC position and the volume control ON before the CD player will operate.
Page 217 Seek Press the top of the SEEK button for the next selection on the CD. Press the bottom of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first 10 seconds of the current selection.
Page 218: Cd/Dvd Changer Operation
218 UNDERSTANDING YOUR INSTRUMENT PANEL CD/DVD Changer Operation Press the MODE button to select between the CD player and the optional remote CD/DVD changer. Time Press the TIME button to change the display from elapsed CD or DVD playing time to time of day. Notes On Playing MP3 Files The radio can play MP3 files, however, acceptable MP3 file recording media and formats are limited.
Page 219 CD audio tracks and computer files (including MP3 files). Discs created with an option such as keep disc open after writing are most likely multisession discs. The use of multisession for CD audio or MP3 playback may result in longer disc loading times. Supported MP3 file formats The radio will recognize only files with the *.mp3 exten- sion as MP3 files.
Page 220: Operation Instructions
220 UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3 files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
Page 221: Disc Cd/Dvd Changer (Rdv)
RW/FF (CD Mode For MP3 Play) Press the FF side of the button to move forward through the MP3 selection. Press the RW side of the button to move back through the MP3 selection. AM/FM Button (CD Mode For MP3 Play) Switches back to Radio mode.
Page 222: Operating Instructions - Cd/Dvd Changer
222 UNDERSTANDING YOUR INSTRUMENT PANEL The CD/DVD Changer will play CD-R, CD-RW, CD- Audio and DVD Video disc formats. The video screen will turn on automatically once a DVD is inserted into the changer. NOTE: The ignition switch must be in the ON or ACC position before the CD/DVD changer will operate.
Page 223 which numbered position the disc will be loaded into. The disc will automatically be pulled into the CD/DVD changer. 3. Upon insertion, the disc will begin to play, and the light below the loading slot will turn off. On vehicles equipped with the premium version the light above the chosen button will remain illuminated.
Page 224: Eject (Ejt) Button
224 UNDERSTANDING YOUR INSTRUMENT PANEL EJECT (EJT) Button If there is a disc in the changer, press the EJT button and the disc will eject. If you do not remove the disc within 10 seconds, it will be reloaded and the display will show PAUSE.
Page 225 Remote Control Buttons 1. Headphone Transmitter 2. Menu Up/Next Track/Chapter 3. Menu Left/Fast Rewind 4. Return 5. Setup 6. Pause/Play 7. Mute 8. Display 9. Mode 10. Program Down - Previous Disc 11. Program Up - Next Disc 12. Slow 13.
Page 226 226 UNDERSTANDING YOUR INSTRUMENT PANEL RTN Button (4) This button only functions in CD/DVD mode. Press this button to return to the previous menu when in the disc menu mode. SETUP Button (5) This button only functions in CD/DVD mode. Press the button after pressing the STOP button to access the set up menu.
Page 227 SLOW Button (12) This button only functions in DVD video mode. Press this button to advance the video. If the DVD is paused, pressing this button will advance the video frame by frame. STOP Button (13) This button only functions in DVD video mode. Press this button to stop the DVD.
Page 228: Operating Instructions - Video Screen
228 UNDERSTANDING YOUR INSTRUMENT PANEL Remote Control Battery Service • To replace the batteries for the remote control slide the cover rearward. The replacement batteries for the remote control are two AAA batteries. Operating Instructions — Video Screen Push up on the release button to lower the video screen. Screen handle 1.
Page 229 2. Enter Button This button will enter the selection from the on-screen menu. 3. Brightness Button Changes the brightness of the screen picture. UNDERSTANDING YOUR INSTRUMENT PANEL 229 Screen Button...
Page 230: Operating Instructions - Headphones
230 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Headphones Rear Headphones 1. Power Button 2. Volume Control 3. Power Indicator Power Button Pressing the power button will turn the headphones ON/OFF. An indicator light will illuminate on the head- phone earpiece to indicate the headphones are ON. NOTE: •...
Page 231 Headphone Battery Service • Press the button at the bottom of each headphone earpiece and lift the cover upward. Headphone Battery Service • Replace the battery in each earpiece and reinstall the cover. The headphones require two AAA batteries. UNDERSTANDING YOUR INSTRUMENT PANEL 231 General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada.
Page 232: Operating Instructions - Mp3 Player, Portable Walkman
232 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Direct sunlight or objects blocking the line of sight between the headphone transmitter on the video screen and the headphones. Operating Instructions — MP3 Player, Portable Walkman An MP3 player can be connected to the audio system. Connect the cables to the RCA jacks located on the front of the CD/DVD changer.
Page 233: Satellite Radio - If Equipped
The navigation DVD unit is located in the underfloor storage compartment in the rear cargo area. A single disc containing map information for the entire United States and parts of Canada is stored in the DVD unit. Updated DVD’s are available from your authorized dealer. Navigation DVD Location UNDERSTANDING YOUR INSTRUMENT PANEL 233 To replace the navigation map DVD lift the storage bin...
Page 234: System Activation
234 UNDERSTANDING YOUR INSTRUMENT PANEL System Activation To activate your Sirius Satellite Radio service, call the toll-free number 888-539-7474, or visit the Sirius web site at www.sirius.com. Please have the following informa- tion available when activating your system: 1. The Electronic Serial Number/Sirius Identification Number (ESN/SID).
Page 235: Rbk Radios
mode when any other button is pushed, the ignition is turned OFF, or 5 minutes has passed since any button was pushed. Selecting Satellite Mode in RBB, RAH and RBK Radios Press the MODE button repeatedly until S A appears in the display.
Page 236: Storing And Selecting Pre-Set Channels
236 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Channels that may contain objectionable content can be blocked. Contact Sirius Customer Care at 888-539- 7474 to discuss options for channel blocking or unblock- ing. Please have your ESN/SID information available. Storing and Selecting Pre-Set Channels In addition to the 10 AM and 10 FM pre-set stations, you may also commit 10 satellite stations to push button memory.
Page 237: Satellite Antenna
Satellite Antenna To ensure optimum reception, do not place items on the roof around the rooftop antenna location or strap items to the trunk lid around the trunk lid antenna (if equipped). Metal objects placed within the line of sight of the antenna will cause decreased performance.
Page 238: Radio Operation
238 UNDERSTANDING YOUR INSTRUMENT PANEL The left hand rocker switch has a push button in the center. The function of the left hand switch is different depending on which mode you are in. The following describes the left hand rocker switch operation in each mode: Radio Operation Pressing the top of the switch will SEEK up for the next...
Page 239: Cassette Tape And Player Maintenance
CASSETTE TAPE AND PLAYER MAINTENANCE To keep the cassette tapes and player in good condition, take the following precautions: 1. Do not use cassette tapes longer than C-90; otherwise, sound quality and tape durability will be greatly dimin- ished. 2. Keep the cassette tape in its case to protect from slackness and dust when it is not in use.
Page 240: Cd/Dvd Disc Maintenance
240 UNDERSTANDING YOUR INSTRUMENT PANEL CD/DVD DISC MAINTENANCE To keep the CD/DVD discs in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge.
Page 241: Manual Air Conditioning And Heating System
Manual Air Conditioning and Heating System Manual Heating and A/C Controls Power Button When the “POWER” button is pressed the indicator will illuminate and the blower will run at the speed selected by the front blower control. When the button is pressed a UNDERSTANDING YOUR INSTRUMENT PANEL 241 second time the indicator light turns off, the blower will turn off and the system will be positioned in the recircu-...
Page 242: Mode Control
242 UNDERSTANDING YOUR INSTRUMENT PANEL Dual Zone Temperature Control — If Equipped With the Dual Zone Temperature Control System, each front seat occupant can independently control the tem- perature of air coming from the outlets on their side of the vehicle. DUAL ZONE TEMP CONTROL This is accomplished by having a separate temperature control lever for both the driver and front seat passenger.
Page 243 UNDERSTANDING YOUR INSTRUMENT PANEL 243 Air comes from the outlets in the instrument panel. Each Panel Mode of these outlets can be individually adjusted to direct the flow of air. Moving the air vane knob on the center outlets down, will close off the air flow from the center outlets.
Page 244 244 UNDERSTANDING YOUR INSTRUMENT PANEL Bi-Level Mode Bi-Level Outlets Air comes from both the instrument panel outlets, floor outlets and defrost. A slight amount of air is also directed through the side window demister outlets. NOTE: In many temperature lever positions, the bi- level mode is designed to provide cooler air out of the panel outlets and warmer air from the floor outlets.
Page 245 Floor Mode Floor Outlets Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. UNDERSTANDING YOUR INSTRUMENT PANEL 245 Mix Mode Mix Outlets Air comes from the floor, defrost and side window demist outlets.
Page 246 246 UNDERSTANDING YOUR INSTRUMENT PANEL Defrost Mode Defrost Outlets Air comes from the windshield and side window demist outlets. Use this setting when necessary to defrost your windshield and side windows. NOTE: For improved safety, the compressor is activated and the recirculation mode is deactivated when Mix or Defrost modes are selected.
Page 247 NOTE: • The compressor will not engage until the engine has been running for a few seconds. • If your air conditioning performance seems lower than expected, check the A/C air filter (ATC equipped vehicles only) and the front of the A/C condenser for an accumulation of dirt or insects.
Page 248 248 UNDERSTANDING YOUR INSTRUMENT PANEL • If the recirculation button is pressed while in the Mix or Defrost mode, the indicator light in the recirculation button will flash 3 times indicating that recirculation is not allowed. A/C Recirculation Programming The recirculation control is programmed to cancel the recirculation mode when the ignition key is turned OFF and will reset to outside air mode when the ignition key is turned ON.
Page 249 Dual-Zone Automatic Temperature Control The Dual Zone Automatic Temperature Control (ATC) System automatically maintains the interior comfort level desired by the driver and front seat passenger. This is accomplished by using two infrared sensors located in the center of the instrument panel. The two infrared sensors independently measure the surface temperature of the driver and front seat passenger.
Page 250 250 UNDERSTANDING YOUR INSTRUMENT PANEL temperature you would like the system to maintain. When the system is set to your comfort level, it is not necessary to change the settings. You will experience the greatest efficiency by allowing the system to function automatically.
Page 251 This feature may be enabled using the following proce- dure: • Press and hold the Heated Rear Window and Auto HI buttons for 5 seconds. • The “DELAY” symbol will flash to indicate that the feature as been enabled. Power Button This button turns the entire system ON/OFF.
Page 252 252 UNDERSTANDING YOUR INSTRUMENT PANEL The front blower control can be set to any fixed blower speed by pressing the rocker switch up or down. This allows the front occupants to control the volume of air circulated in the vehicle and cancel the auto mode.
Page 253 UNDERSTANDING YOUR INSTRUMENT PANEL 253 Air comes from both the instrument panel outlets and Bi-Level Mode floor outlets. A slight amount of air is also directed through the defrost and side window demister outlets. NOTE: In many temperature positions, the bi-level mode is designed to provide cooler air out of the panel outlets and warmer air from the floor outlets.
Page 254 254 UNDERSTANDING YOUR INSTRUMENT PANEL Floor Mode Floor Outlets Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. Mix Mode Mix Outlets Air comes from the floor, defrost and side window demist outlets.
Page 255 Defrost Mode Defrost Outlets Air comes from the windshield and side window demist outlets. Use this setting when necessary to defrost your windshield and side windows. If a fog or mist on the UNDERSTANDING YOUR INSTRUMENT PANEL 255 windshield or side glass starts to impair visibility, press the front blower button and increase the fan speed to maximum.
Page 256 256 UNDERSTANDING YOUR INSTRUMENT PANEL windshield or side glass starts to impair visibility, press the front blower button and increase the fan speed to maximum. Recirculation Control When the outside air contains smoke, odors, high humidity, or if rapid cooling is desired you may wish to recirculate interior air by pressing the recirculation button.
Page 257 • While holding the recirculation button, turn the igni- tion switch to the “RUN” position. • Continue holding the recirculation button for 4 sec- onds, then release. The recirculation control is now programmed so that the recirculation mode will not reset to the outside air mode when the engine is restarted.
Page 258 258 UNDERSTANDING YOUR INSTRUMENT PANEL glycol antifreeze coolant in water is recommended. Refer to section 7, Maintenance Procedures, of this manual for proper coolant selection. Winter Operation To insure the best possible heater and defroster perfor- mance, make sure the engine cooling system is function- ing properly and the proper amount, type, and concen- tration of coolant is used.
Page 259 A/C Air Filter — If Equipped On vehicles equipped with Automatic Temperature Con- trol (ATC), the climate control system filters out dust and pollen from the air. Refer to section 7 “Air Conditioning” for filter replacement instructions. Outside Temperature Display The outside temperature can be shown in the ATC display by pressing the OUTSIDE TEMP button.
Page 261: Starting And Operating
STARTING AND OPERATING CONTENTS Starting Procedures ..... 266 Automatic Transmission ....267 Normal Starting (Above 32°F / 0°C) .
Page 262 262 STARTING AND OPERATING Parking Brake ......276 Brake System ......278 Anti-Lock Brake System .
Page 263 Replacement Tires ..... 304 Alignment And Balance ....305 Tire Chains .
Page 264 264 STARTING AND OPERATING Carbon Monoxide Warnings ....321 Adding Fuel ......321 Fuel Filler Cap (Gas Cap) .
Page 265 Towing Requirements ....336 Towing Tips ......340 Recreational Towing (Behind Motorhome, Etc.) .
Page 266: Starting Procedures
266 STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. WARNING! • Be sure to turn off the engine if you want to rest or sleep in your car. Accidents can be caused by inadvertently moving the gear selection lever or by pressing the accelerator pedal.
Page 267: Automatic Transmission
Automatic Transmission The gear selector must be in the NEUTRAL or PARK position before you can start the engine. Depress the brake pedal before shifting into any driving gear. Normal Starting (Above 32°F / 0°C) 1. Do not depress the accelerator. 2.
Page 268: If Engine Fails To Start
268 STARTING AND OPERATING If Engine Fails To Start If the engine fails to start after you have followed the normal starting procedure, it may be flooded. Push the accelerator pedal all the way to the floor and hold it there while cranking the engine.
Page 269: After Starting
WARNING! Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic trans- mission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
Page 270: Engine Block Heater - If Equipped
270 STARTING AND OPERATING ENGINE BLOCK HEATER — IF EQUIPPED The engine block heater warms engine coolant and permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt AC electrical outlet with a grounded, three-wire extension cord. The engine block heater cord is routed under the hood on the driver side of the vehicle.
Page 271: Brake/Transmission Interlock System
WARNING! It is dangerous to shift the selector lever out of “P” or “N” if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in re- verse.
Page 272 272 STARTING AND OPERATING Reset Mode - Electronic Transmission The transmission is monitored electronically for abnor- mal conditions. If a condition is detected that could cause damage, the transmission automatically shifts into sec- ond gear. The transmission remains in second gear despite the forward gear selected.
Page 273 WARNING! Never use Park position on an automatic transmis- sion as a substitute for the parking brake. Always apply parking brake fully when parked to guard against vehicle movement and possible injury or damage. For electrical system malfunctions there is an override for the interlock system.
Page 274: Autostick
274 STARTING AND OPERATING “N” Neutral Engine may be started in this range. “D” Overdrive To be used for most city and highway driving, it provides smoothest upshifts and downshifts and best fuel economy. When frequent transmission shifting occurs while using the “D” Overdrive position, such as when operating the vehicle under heavy loading conditions, (i.e.
Page 275: Autostick General Information
You can shift in or out of the AutoStick mode at any time without taking your foot off the accelerator pedal. If you choose the Overdrive mode, the transmission will oper- ate automatically; shifting between the four available gears. When you wish to engage AutoStick, simply move the shift lever to the AUTOSTICK position.
Page 276: All Wheel Drive - If Equipped
276 STARTING AND OPERATING • If the system detects a problem it will disable the AutoStick mode and the transmission will return to the automatic mode until the problem is corrected. ALL WHEEL DRIVE — IF EQUIPPED This feature provides full time, on-demand, All Wheel Drive (AWD).
Page 277 Before leaving the vehicle, make sure that the parking brake is fully applied and place the gear selector in the Park position. To release the parking brake, pull out on the parking brake release located on the left side of the instrument panel.
Page 278: Brake System
278 STARTING AND OPERATING WARNING! • Always fully apply the parking brake when leav- ing your vehicle, or it may roll and cause damage or injury. Also be certain to leave an automatic transmission in Park, a manual transmission in Reverse or first gear.
Page 279: Anti-Lock Brake System
Anti-Lock Brake System The Anti-Lock Brake System provides increased vehicle stability and brake performance under most braking conditions. The system automatically “pumps” the brakes during severe braking conditions to prevent wheel lock-up. WARNING! Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to an accident.
Page 280 280 STARTING AND OPERATING The ABS light monitors the Anti-Lock Brake System. The light will come on when the ignition switch is turned to the ON position and may stay on for as long as four seconds. If the ABS light remains on or comes on while driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required.
Page 281: Electronic Stability Program (Esp)
• and a slight drop or fall away of the brake pedal at the end of the stop. These are all normal characteristics of ABS. WARNING! The Anti-Lock Brake System contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting equipment.
Page 282 282 STARTING AND OPERATING applies the brake of the appropriate wheel to assist in counteracting the Over-steer or Under-steer condition. • Over-steer: when the vehicle is turning more than appropriate for the steering wheel position. • Under-steer: when the vehicle is turning less than appropriate for the steering wheel position.
Page 283: Esp Has The Following Operating Modes
ESP has the following operating modes: • ESP On This is the normal operating mode for ESP. Whenever the vehicle is started the ESP system will be in this mode. This mode should be used for almost all driving situations. ESP should only be turned to “Partial Off”...
Page 284: Brake Assist System (Bas)
284 STARTING AND OPERATING go out with the engine running. If the “ESP/BAS Warn- ing Lamp” comes on continuously with the engine running, a malfunction has been detected in either the ESP or BAS system, or both. If this light remains on after several ignition cycles, and the vehicle has been driven several miles at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible to have the...
Page 285: Traction Control
TRACTION CONTROL This system monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s) and engine power is reduced to provide enhanced acceleration and stability. A feature of the TCS system functions similar to a limited slip differential and controls the wheel spin across a driven axle.
Page 286: Power Steering
286 STARTING AND OPERATING • The system has been deactivated to prevent damage to the brake system due to overheated brake tempera- tures NOTE: • The Traction Control system will make buzzing or clicking sounds when in operation. • Extended heavy use of Traction Control may cause the system to deactivate and turn on the traction control indicator located in the instrument cluster.
Page 287: Driving On Slippery Surfaces
WARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. CAUTION! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and it should be avoided when possible.
Page 288: Traction
288 STARTING AND OPERATING Traction When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is known as hydroplaning and may cause partial or complete loss of vehicle control and stopping ability.
Page 289 • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter P is absent from this tire size designation. Example: 215/65R15 96H •...
Page 290 290 STARTING AND OPERATING Tire Sizing Chart Size Designation: P = Passenger car tire size based on U.S. design standards ...blank... = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Millimeters (mm)
Page 291 Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved un- der specified operating conditions.
Page 292: Tire Identification Number (Tin)
292 STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire; however, the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code DOT = Department of Transportation —This symbol certifies that the tire is in compliance with the U.S.
Page 293: Tire Loading And Tire Pressure
Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar. Tire Placard Location STARTING AND OPERATING 293 Tire and Loading Information Placard Tire and Loading Information This placard tells you important information about the: 1) number of people that can be carried in the vehicle...
Page 294 294 STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the “Tire and Loading Information”...
Page 295 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle.
Page 296 296 STARTING AND OPERATING...
Page 297: Tires - General Information
WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
Page 298: Tire Inflation Pressures
298 STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear pat- terns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation, also increases tire rolling resistance and results in higher fuel consumption.
Page 299 CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure.”...
Page 300: Radial-Ply Tires
300 STARTING AND OPERATING loading may be required for high-speed vehicle opera- tion. Refer to original equipment or an authorized tire dealer for recommended safe operating speeds, loading and cold tire inflation pressures. WARNING! High speed driving with your vehicle under maxi- mum load is dangerous.
Page 301: Compact Spare Tire - If Equipped
Compact Spare Tire — If Equipped The compact spare is for temporary emergency use with radial tires. It is engineered to be used on your style vehicle only. Since this tire has limited tread life, the original tire should be repaired (or replaced) and rein- stalled at the first opportunity.
Page 302: Limited Use Spare - If Equipped
302 STARTING AND OPERATING Limited Use Spare — If Equipped The limited use spare tire is for temporary emergency use on your vehicle. This tire is identified by a limited use spare tire warning label located on the limited use spare tire and wheel assembly.
Page 303: Tread Wear Indicators
WARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) for more than 30 seconds continuously when you are stuck, and don’t let anyone near a spinning wheel, no matter what the speed.
Page 304: Life Of Tire
304 STARTING AND OPERATING Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: • Driving style • Tire pressure • Distance driven WARNING! Tires and spare tire should be replaced after six years, regardless of the remaining tread.
Page 305: Alignment And Balance
WARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of un- approved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle.
Page 306: Tire Chains
306 STARTING AND OPERATING Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-of- balance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. TIRE CHAINS Use only compact chains, or other traction aids that meet SAE type “Class S”...
Page 307: Snow Tires
NOTE: In order to avoid damage to tires, chains, and your vehicle do not drive for a prolonged period of time on dry pavement. Observe the tire chain manufacturer’s instructions on method of installation, operating speed, and conditions for usage. Always use the lower suggested operating speed if both the chain manufacturer and vehicle manufacture suggest a maximum speed.
Page 308: Tire Pressure Monitor System - If Equipped
308 STARTING AND OPERATING Follow the recommended tire rotation frequency for your type of driving found in the “Maintenance Schedules” Section of this manual. More frequent rotation is permis- sible if desired. The reasons for any rapid or unusual wear should be corrected prior to rotation being per- formed.
Page 309: Tire Pressure Monitoring Base System Without Electronic Vehicle Information Center (Evic) - If Equipped
• The Tire Pressure Monitoring System (TPMS) will warn the driver of a low tire pressure if the tire pressure falls below the low pressure warning thresh- old for any reason, including low temperature effects. • The Tire Pressure Monitoring System (TPMS) will continue to warn the driver of low tire pressure as long as the condition exists, and will not turn off until the tire pressure is at or above recommended cold placard...
Page 310: Tire Pressure Monitoring Low Pressure Warnings
310 STARTING AND OPERATING Tire Pressure Monitoring Low Pressure Warnings The Tire Pressure Monitoring Telltale Lamp will illuminate in the instrument cluster and an audible chime will be activated when one or more of the four active road tire pressures are low.
Page 311 The Tire Pressure Monitor System (TPMS) consists of the following components: • Receiver Module • 4 Tire Pressure Monitoring Sensors • Various Tire Pressure Monitoring System Messages, which display in the Electronic Vehicle Information Center (EVIC) • Tire Pressure Monitoring Telltale Lamp The Tire Pressure Monitoring Telltale Lamp will illumi- nate in the instrument cluster and an audible chime will be activated when one or more of the four active road tire...
Page 312: Service Tire System Soon
312 STARTING AND OPERATING Service Tire System Soon The Tire Pressure Monitoring Telltale Lamp will flash on and off for 60 seconds in the instrument cluster, and an audible chime will be activated when one or more of the four active road tire pressures are low. In addition the Electronic Vehicle Information Center (EVIC) will display a “SERVICE TIRE SYSTEM SOON”...
Page 313: Using Your Compact Spare - Basic Tire Pressure Monitoring System Only
CAUTION! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the wheel rim sensor. NOTE: • The Tire Pressure Monitoring System does not monitor the temporary spare tire.
Page 314: Tire Pressure Monitoring Premium System - If Equipped
314 STARTING AND OPERATING Monitoring Lamp to be ON, and a Chime will sound. This sequence will repeat for every key cycle until the original Tire Pressure Monitoring System tire has been properly repaired (or replaced) and put back on the vehicle in place of the compact spare tire.
Page 315: Service Tire System Soon
NOTE: A low spare tire will not cause the Tire Pressure Monitoring System Telltale Lamp to illuminate or the chime to sound. Should a low tire condition occur on any of the four active road tire(s), you should stop as soon as possible, and inflate the low tire(s) that is/are flashing on the graphic display to the vehicle’s recommended cold plac- ard pressure value.
Page 316 316 STARTING AND OPERATING NOTE: Your vehicle is equipped with a compact spare wheel and tire assembly that does not have a tire pressure monitoring sensor. Therefore, it will not be monitored by the Tire Pressure Monitoring System. In the event that a compact spare tire is used to replace a low pressure road tire, the next ignition key cycle will still show the Tire Pressure Monitoring Lamp to be ON, a Chime will...
Page 317: General Information
CAUTION! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the wheel rim sensor. NOTE: • The Tire Pressure Monitoring System (TPMS) is not intended to replace normal tire care and maintenance, nor to provide warning of a tire failure or condition.
Page 318: Fuel Requirements
If you experience these symptoms, try another brand of gasoline before consid- ering service for the vehicle. Over 40 automobile manufacturers around the world have issued and endorsed consistent gasoline specifica- tions (the World Wide Fuel Charter, WWFC) to define fuel properties necessary to deliver enhanced emissions, engine performance, and durability for your vehicle.
Page 319: Gasoline/Oxygenate Blends
Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxy- genates such as 10% ethanol, MTBE, and ETBE. Oxygen- ates are required in some areas of the country during the winter months to reduce carbon monoxide emissions. Fuels blended with these oxygenates may be used in your vehicle.
Page 320: Materials Added To Fuel
320 STARTING AND OPERATING Materials Added to Fuel All gasoline sold in the United States is required to contain effective detergent additives. Use of additional detergents or other additives are not needed under normal conditions and would result in additional cost. Therefore you should not have to add anything to the fuel.
Page 321: Carbon Monoxide Warnings
Carbon Monoxide Warnings WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.
Page 322 322 STARTING AND OPERATING The fuel tank filler tube has a restricting door about 2 inches (50 mm) inside the opening. If using a portable fuel container, it should have a flexible nozzle long enough to force open the restricting door. CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel...
Page 323: Loose Fuel Filler Cap Message
NOTE: • Tighten the fuel filler cap until you hear a “clicking” sound. This is an indication that the fuel filler cap is properly tightened. • If the gas cap is not tighten properly, the Malfunction Indicator Light will come on. Be sure the gas cap is tightened every time the vehicle is refueled.
Page 324: Flexible Fuel- (Fleet Vehicles Only)
324 STARTING AND OPERATING FLEXIBLE FUEL— (Fleet Vehicles Only) E-85 General Information The information in this section is for Flexible Fuel ve- hicles only. These vehicles can be identified by the unique fuel filler door label that states Ethanol (E-85) or Un- leaded Gasoline Only.
Page 325: Selection Of Engine Oil For Flexible Fuel
For best results, a refueling pattern that alternates be- tween E-85 and unleaded gasoline should be avoided. When you do switch fuels, it is recommended that • you do not switch when the fuel gauge indicates less than 1/4 full •...
Page 326: Cruising Range
326 STARTING AND OPERATING Cruising Range Because E-85 fuel contains less energy per gallon than gasoline, you will experience an increase in fuel con- sumption. You can expect your MPG and your driving range to decrease by about 30% compared to gasoline operation.
Page 327: Vehicle Certification Label
Vehicle Certification Label Your vehicle has a certification label attached to the rear of the driver’s door. The label contains the following information: • Name of manufacturer • Month and year of manufacture • Gross Vehicle Weight Rating (GVWR) • Gross Axle Weight Rating (GAWR) front •...
Page 328: Overloading
328 STARTING AND OPERATING Overloading The load carrying components (axle, springs, tires, wheels, etc.) of your vehicle will provide satisfactory service as long as you do not exceed the GVWR and front and rear GAWR. The best way to figure out the total weight of your vehicle is to weigh it when it is fully loaded and ready for operation.
Page 329: Trailer Towing
A loaded vehicle is shown in the illustration. Note that neither the GVWR or the GAWR capacities have been exceeded. STARTING AND OPERATING 329 Example Only Front Axle Rear Axle Empty Weight 2538 lbs (1151 kg) Load (Including driver, pas- 223 lbs sengers and cargo) (101 kg)
Page 330: Common Towing Definitions
330 STARTING AND OPERATING Common Towing Definitions The following trailer towing related definitions will assist you in understanding the following information: Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. This includes driver, passengers, cargo and tongue weight.
Page 331 Tongue Weight (TW) The downward force exerted on the hitch ball by the trailer. In most cases it should not be less than 10% or more than 15% of the trailer load. You must consider this as part of the load on your vehicle. Frontal Area The maximum height and maximum width of the front of a trailer.
Page 332 332 STARTING AND OPERATING WARNING! An improperly adjusted Weight Distributing Hitch system may reduce handling, stability, braking per- formance, and could result in an accident. Weight Distributing Systems may not be compatible with Surge Brake Couplers. Consult with your hitch and trailer manufacturer or a reputable Recreational Vehicle dealer for additional information.
Page 333: Trailer Hitch Classification
Improper Adjustment of Weight Distributing System Trailer Hitch Classification Your vehicle may be factory equipped for safe towing of trailers weighing over 2,000 lbs (907 kg) with the optional Trailer Tow Prep Package. See your dealer for package content. STARTING AND OPERATING 333 The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the...
Page 334: Trailer Towing Weights (Maximum Trailer Weight Ratings)
334 STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/Transmission GCWR (Gross Com- bined Wt. Rating) 3.5L & 3.8L Auto- 8,600 lbs (3900 kg) matic 8,600 lbs (3900 kg) 8,600 lbs (3900 kg)
Page 335: Trailer And Tongue Weight
Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to side which will cause loss of control of the vehicle and trailer.
Page 336: Towing Requirements
336 STARTING AND OPERATING NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the Tire and Loading Information plac- ard in the Tire Safety Information Section of this manual for the maximum combined weight of occupants and cargo for your vehicle.
Page 337 WARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control.
Page 338 338 STARTING AND OPERATING 4. Tongue weight rating for the trailer hitch utilized (This requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight). Towing Requirements — Tires −...
Page 339 − Trailer brakes are recommended for trailers over 1,000 lbs (454 kg) and required for trailers in excess of 2,000 lbs (907 kg). CAUTION! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity.
Page 340: Towing Tips
340 STARTING AND OPERATING NOTE: Do not cut or splice wiring into the vehicles wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. 4 - Pin Connector 7- Pin Connector Towing Tips...
Page 341 Towing Tips — Automatic Transmission The “D” range can be selected when towing. However, if frequent shifting occurs while in this range, the “3” range should be selected. NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will improve perfor- mance and extend transmission life by reducing exces- sive shifting and heat build up.
Page 342: Towing This Vehicle Behind Another Vehicle
342 STARTING AND OPERATING − Highway Driving Reduce speed. − Air Conditioning Turn off temporarily. − refer to Cooling System Operating information in the Maintenance section of this manual for more informa- tion. RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) TOWING THIS VEHICLE BEHIND ANOTHER VEHICLE (Flat towing with all four wheels on the ground) Recreational towing for this vehicle is not recommended.
Page 343: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....344 If Your Engine Overheats ....345 Jacking And Tire Changing .
Page 344: Hazard Warning Flasher
344 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER Hazard Flasher Switch The hazard flasher switch is located in the center of the instrument panel above the center air outlets. To engage the Hazard Warning Flashers, depress the switch on the instrument panel. When the Hazard Warn- ing Switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emer- gency.
Page 345: If Your Engine Overheats
NOTE: With extended use, the Hazard Warning Flash- ers may wear down your battery. IF YOUR ENGINE OVERHEATS In any of the following situations, you can reduce the potential for overheating by taking the appropriate ac- tion. • On the highways — Slow down. •...
Page 346: Jacking And Tire Changing
346 WHAT TO DO IN EMERGENCIES WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, see Section 7, Maintenance, of this manual.
Page 347 Remove the scissors jack and jack handle by rotating the small wing nut to the left. Jack Wing Nut WHAT TO DO IN EMERGENCIES 347 Six Passenger Seating The jack and jack-handle are stowed in the rear storage bin located in the rear cargo floor. Pull up on the storage bin cover and liner to access the jack and jack tools.
Page 348: Spare Tire Stowage
348 WHAT TO DO IN EMERGENCIES Spare Tire Stowage Five Passenger Seating The spare tire is stowed under the rear of the vehicle by means of a cable winch mechanism. To remove or stow the spare, use the jack handle to rotate the “spare tire drive”...
Page 349: Preparations For Jacking
CAUTION! The winch mechanism is designed for use with the jack handle only. Use of an air wrench or other power tools is not recommended and can damage the winch. When the spare is clear, tilt the retainer at the end of the cable and pull it through the center of the wheel.
Page 350: Jacking Instructions
350 WHAT TO DO IN EMERGENCIES Jacking Instructions WARNING! • Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack.
Page 351 1. Remove the spare wheel, scissors jack and jack-handle from stowage. 2. Carefully pry off the wheel center cap if equipped, using the tip of the jack handle. 3. Loosen (but do not remove) the wheel lug nuts by turning them to the left one turn while the wheel is still on the ground.
Page 352 352 WHAT TO DO IN EMERGENCIES location. Do not raise the vehicle until you are sure the jack is securely engaged. Never jack up the vehicle using any suspension components. 6. Raise the vehicle by turning the jack screw to the right, using the swivel wrench.
Page 353 lug nuts until each nut has been tightened twice. Correct wheel nut tightness is 130 N·m (95 ft. lbs). If in doubt about the correct tightness, have them checked with a torque wrench by your dealer or at a service station. 11.
Page 354: Jump-Starting Procedure
354 WHAT TO DO IN EMERGENCIES NOTE: When reinstalling the wheel center cap, insure that the valve stem symbol on the back of the cap is pointed toward the wheel valve stem. Install the center cap using hand pressure only. Do not use a hammer. Wheel Nuts All wheel nuts should be tightened occasionally to elimi- nate the possibility of wheel studs being sheared or the...
Page 355 Check the Battery Test Indicator (if equipped). If a light or bright colored dot is visible in the indicator (if equipped), DO NOT jump-start the battery. If the indicator (if equipped) is dark or shows a green dot, proceed as follows: 1.
Page 356: Freeing A Stuck Vehicle
356 WHAT TO DO IN EMERGENCIES WARNING! Do not connect the cable to the negative post of the discharge battery. The resulting electrical spark could cause the battery to explode. During cold weather when temperatures are below freezing point, electrolyte in a discharged battery may freeze.
Page 357: Towing A Disabled Vehicle
WARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck. And don’t let anyone near a spinning wheel, no matter what the speed.
Page 358: Without The Ignition Key
358 WHAT TO DO IN EMERGENCIES and rear wheels must be on the ground. If your vehicle must be towed farther or at a higher rate of speed, it must be transported on a flat bed truck. All Transmissions CAUTION! •...
Page 359: Towing This Vehicle Behind Another Vehicle With A Tow Dolly
WHAT TO DO IN EMERGENCIES 359 TOWING THIS VEHICLE BEHIND ANOTHER VEHICLE WITH A TOW DOLLY The manufacturer does not recommend that you tow an All-Wheel Drive (AWD) or front wheel drive vehicle on a tow dolly. Vehicle damage may occur.
Page 361 MAINTAINING YOUR VEHICLE CONTENTS 4.0L Engines ......364 3.8L Engines ......365 Onboard Diagnostic System —...
Page 362 362 MAINTAINING YOUR VEHICLE Front & Rear Suspension Ball Joints ..380 Steering Shaft Seal ....380 Steering Linkage .
Page 363 Front Park/Turn Signal And Sidemarker Lights ......408 Front Fog Light ..... . 409 Rear Tail, Stop, Turn Signal, Side Marker And Back-Up Lights .
Page 364: 4.0L Engines
364 MAINTAINING YOUR VEHICLE 4.0L ENGINES Engine Compartment 4.0L Engine...
Page 365: L Engines
MAINTAINING YOUR VEHICLE 365 3.8L ENGINES Engine Compartment 3.8L Engines...
Page 366: Onboard Diagnostic System - Obd Ii
366 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emis- sions well within current government regulations.
Page 367: Emissions Inspection And Maintenance
cap until a clicking sound is heard. This is an indication that the gas cap is properly tightened. Press the odometer reset button to turn the message off. If the problem persists, the message will appear the next time the vehicle is started.
Page 368: Replacement Parts
368 MAINTAINING YOUR VEHICLE 4. As soon as you turn your key to the ON position, you will see your MIL symbol come on as part of a normal bulb check. 5. Approximately 15 seconds later, one of two things will happen: a.
Page 369: Dealer Service
DEALER SERVICE Your dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner. Service Manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any procedure yourself. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you.
Page 370 370 MAINTAINING YOUR VEHICLE The best time to check the engine oil level is about 5 minutes after a fully warmed engine is shut off or before starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings.
Page 371 Change Engine Oil Road conditions and your kind of driving affects the interval at which your oil should be changed. Check the following list to see if any apply to you. • Day or night temperatures are below 32°F (0°C). •...
Page 372 372 MAINTAINING YOUR VEHICLE American Petroleum Institute (API) Engine Oil Identification Symbol This symbol means that the oil has been certified by the American Petroleum Institute (API). The manufacturer only recommends API Certified engine oils. Engine Oil Viscosity (SAE Grade) — 4.0 Liter Engines The proper SAE viscosity grade of engine oil should be selected based on the following recommendation and be...
Page 373 Engine Oil Viscosity (SAE Grade) — 3.8 Liter Engines SAE 5W-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. Your engine oil filler cap also shows the recommended engine oil viscosity for your vehicle.
Page 374: Engine Oil Filter
374 MAINTAINING YOUR VEHICLE Engine Oil Filter The engine oil filter should be replaced at every engine oil change. Engine Oil Filter Selection This manufacture’s engines have a full-flow type oil filter. Use a filter of this type for replacement. The quality of replacement filters varies considerably.
Page 375: Catalytic Converter
WARNING! The air cleaner can provide a measure of protection in the case of engine backfire. Do not remove the air cleaner unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air cleaner removed.
Page 376: Maintenance-Free Battery
376 MAINTAINING YOUR VEHICLE NOTE: Intentional tampering with emissions control sys- tems can result in civil penalties being assessed against you. WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your ex- haust system.
Page 377 WARNING! • Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area imme- diately with large amounts of water.
Page 378: Air Conditioner Maintenance
378 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an Authorized Dealer at the start of each warm season. This service should include cleaning of the condenser fins and a system performance check.
Page 379: Power Steering - Fluid Check
Refrigerant Recovery And Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocar- bon (HFC) that is endorsed by the Environmental Pro- tection Agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by dealers or other service facilities using recovery and recycling equipment.
Page 380: Front & Rear Suspension Ball Joints
380 MAINTAINING YOUR VEHICLE WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to insure accurate fluid level reading. Do not overfill. Use only manufacturers recommended power steering fluid. If necessary, add fluid to restore to the proper indicated level.
Page 381: Body Lubrication
Continued operation could result in failure of the univer- sal joint due to water and dirt contamination of the grease. This would require complete replacement of the joint assembly. Body Lubrication Locks and all body pivot points, including such items as seat tracks, doors, liftgate and hood hinges, should be lubricated periodically to assure quiet, easy operation and to protect against rust and wear.
Page 382: Windshield And Rear Window Washers
382 MAINTAINING YOUR VEHICLE Windshield and Rear Window Washers The fluid reservoir for the windshield washers and the rear window washer is shared. It is located in the engine compartment and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) and operate the system for a few seconds to flush out the residual water.
Page 383: Cooling System
vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment.
Page 384 384 MAINTAINING YOUR VEHICLE Engine Coolant Checks Check the engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If coolant is dirty or rusty in appearance, the system should be drained, flushed and refilled with fresh coolant.
Page 385 CAUTION! Mixing of coolants other than specified HOAT en- gine coolants, may result in engine damage and may decrease corrosion protection. If a non-HOAT cool- ant is introduced into the cooling system in an emergency, it should be replaced with the specified coolant as soon as possible.
Page 386 386 MAINTAINING YOUR VEHICLE The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area where the vehicle is operated.
Page 387 do not store ethylene glycol based engine coolant in open containers or allow it to remain in puddles on the ground. If ingested by a child, contact a physician immediately. Clean up any ground spills immediately. Engine Coolant Level The coolant bottle provides a quick visual method for determining that the coolant level is adequate.
Page 388: Hoses And Vacuum/Vapor Harnesses
388 MAINTAINING YOUR VEHICLE • Check coolant freeze point in the radiator and in the coolant recovery bottle. If antifreeze needs to be added, contents of coolant recovery bottle must also be protected against freezing. • If frequent coolant additions are required, or if the level in the coolant recovery bottle does not drop when the engine cools, the cooling system should be pres- sure tested for leaks.
Page 389: Brakes
Inspect all hose connections such as clamps and couplings to make sure they are secure and no leaks are present. Components should be replaced immediately if there is any evidence of wear or damage that could cause failure. Brakes In order to assure brake system performance, all brake system components should be inspected periodically.
Page 390: Master Cylinder - Brake Fluid Level Check
390 MAINTAINING YOUR VEHICLE hot fluid when systems are under pressure (during vehicle operation), should be noted before a hose is replaced based on leakage. NOTE: Inspection of brake hoses should be performed whenever the brake system is serviced and at every engine oil change.
Page 391: Fuel System Hoses
WARNING! • Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. • Use of brake fluid that may have a lower initial boiling point or unidentified as to specification, may result in sudden brake failure during hard prolonged braking.
Page 392: Automatic Transmission
392 MAINTAINING YOUR VEHICLE Care should be taken in installing quick connect fittings to insure they are properly installed and fully connected. See your authorized dealer for service. Automatic Transmission The automatic transmission and differential assembly are contained within a single housing. All automatic transmissions are equipped with a conven- tional filler tube and dipstick.
Page 393 Procedure For Checking Fluid Level The fluid level in the automatic transmission should be checked whenever the vehicle is serviced. Operation with an improper fluid level will greatly reduce the life of the transmission and of the fluid. To properly check the automatic transmission fluid level, the following procedure must be used: 1.
Page 394 394 MAINTAINING YOUR VEHICLE b. If the fluid is cold, the fluid level should be between the lower two holes in the area marked “COLD”. If the fluid level indicates low, add sufficient fluid to bring to the proper level. CAUTION! Do not overfill.
Page 395: All Wheel Drive (Awd) - If Equipped
All Wheel Drive (AWD) — If Equipped Under normal operating conditions, periodic fluid level checks and lubricant changes for the Power Transfer Unit and Rear Carrier, are not required. However when the vehicle is serviced for other reasons, the exterior surface of these components should be inspected for evidence of fluid leaks.
Page 396: Front And Rear Wheel Bearings
396 MAINTAINING YOUR VEHICLE Severe Usage is defined as: 1. More than 50% of vehicle operation in stop and go traffic where vehicle is driven regularly for more than 45 minutes of continuous operation, such as in heavy city or in construction zone traffic, 2.
Page 397 The most common causes are: • Road salt, dirt and moisture accumulation. • Stone and gravel impact. • Insects, tree sap and tar. • Salt in the air near seacoast localities. • Atmospheric fallout/industrial pollutants. Washing • Wash your vehicle regularly. Always wash your ve- hicle in the shade using Mopar Car Wash or a mild car wash soap, and rinse the panels completely with clear water.
Page 398 398 MAINTAINING YOUR VEHICLE • It is important that the drain holes in the lower edges of the doors, rocker panels and trunk be kept clear and open. • If you detect any stone chips or scratches in the paint, touch them up immediately.
Page 399 Interior Care Cleaning Interior Fabric Upholstery Your interior seat Yes Essentials™ fabric upholstery should be cleaned in the following manner: • Remove as much of the stain as possible by blotting with a clean, dry towel. • Blot any remaining stain with a clean, damp towel. •...
Page 400 400 MAINTAINING YOUR VEHICLE upholstery. Application of a leather conditioner is not required to maintain the original condition. WARNING! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm. Glass Surfaces All glass surfaces should be cleaned on a regular basis with Mopar Glass Cleaner or any commercial household-...
Page 401: Cleaning The Center Console Cup Holders
Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water.
Page 402: Fuses (Integrated Power Module)
402 MAINTAINING YOUR VEHICLE FUSES (INTEGRATED POWER MODULE) Integrated Power Module (IPM) An Integrated Power Module (IPM) is located in the engine compartment near the battery. This center con- tains maxi fuses, mini fuses and relays. A label that identifies each component is printed on the inside of the cover.
Page 403 Cavity Cartridge Description Fuse 40 Amp Power Sunroof Green Spare 40 Amp Headlight Washer, Power Green Liftgate Spare 40 Amp Radiator Fan 1 Green Spare 40 Amp Anti-Lock Brake System Green (ABS) Module 40 Amp Driver Door Node Green 40 Amp Passenger Door Node Green MAINTAINING YOUR VEHICLE 403...
Page 404 404 MAINTAINING YOUR VEHICLE Cavity Mini Fuse 20 Amp Yel- Cluster, CHMSL, Stop Lights, Anti-Lock Brake System (ABS) 10 Amp Red Ignition Switch 20 Amp Yel- Hazard Spare Spare 20 Amp Yel- Electronic Automatic Transaxle (EATX) Solenoid 25 Amp Natural 20 Amp Yel- Fuel Pump 20 Amp Yel-...
Page 405: Vehicle Storage
CAUTION! • When installing the Integrated Power Module cover, it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the Integrated Power Module, and possibly result in a electrical system failure.
Page 406: Replacement Light Bulbs
406 MAINTAINING YOUR VEHICLE REPLACEMENT LIGHT BULBS LIGHT BULBS — Interior Center & Rear Reading Lights ....578 Front Door Courtesy Light ....578 Liftgate Light(s).
Page 407: High Intensity Discharge Headlights (Hid) - If Equipped
2. Disconnect the electrical connector. 3. Remove the rubber boot seals. 4. Rotate the bulb to the left and replace the bulb. Reinstall the rubber boot seals and then the headlight module. MAINTAINING YOUR VEHICLE 407 CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life.
Page 408: Front Park/Turn Signal And Sidemarker Lights
408 MAINTAINING YOUR VEHICLE WARNING! A transient high tension occurs at the bulb sockets of High Intensity Discharge (HID) headlights when the headlight switch is turned ON. It may cause serious electrical shock or electrocution if not serviced prop- erly. See your authorized dealer for service. NOTE: On vehicles equipped with High Intensity Dis- charge Headlights (HID), when the headlights are turned on there is a blue hue to the lights.
Page 409: Front Fog Light
Front Fog Light 1. Reach under the front fascia and grasp the front fog light bulb. 2. Twist the front fog light bulb to remove from the fog light module. 3. Disconnect the electrical connector and replace the bulb. CAUTION! Do not touch the new bulb with your fingers.
Page 410: License Light
410 MAINTAINING YOUR VEHICLE 3. Twist the socket assembly to remove it from the housing. 4. Pull the bulb out of the socket. 5. Replace the bulb, reinstall the socket, and reattach the tail light assembly. License Light 1. Place a screwdriver in the slot next to the release tab and push on the release tab to remove the lens.
Page 411: Fluids And Capacities
FLUIDS AND CAPACITIES Fuel Engine Oil-With Filter 4.0 Liter Engines (SAE 10W-30, API Certified) 3.8 Liter Engines (SAE 5W-20, API Certified) Cooling System * 4.0 Liter Engines (Mopar Antifreeze/Coolant 5 Year/ 100,000 Mile Formula or equivalent) 3.8 Liter Engines (Mopar Antifreeze/Coolant 5 Year/ 100,000 Mile Formula or equivalent) * Includes heater and coolant recovery bottle filled to MAX level.
Page 412: Fluids, Lubricants And Genuine Parts
412 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant 4.0 Liter Engine Oil 3.8 Liter Engine Oil Spark Plugs Oil Filter, 4.0/3.8 Liter Engines Fuel Selection Fluids, Lubricants and Genuine Parts Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Or- ganic Additive Technology) or equivalent Use API Certified SAE 10W-30 engine oil, refer to oil viscosity chart for cor- rect SAE grade meeting DaimlerChrysler Material Standard MS-6395.
Page 413: Chassis
Chassis Component Automatic Transmission AWD Power Transfer Unit AWD Rear Carrier Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts Mopar ATF+4 Automatic Transmission Fluid. Mopar Gear Lubricant 75W-90 or equivalent. Mopar Gear Lubricant 75W-90 or equivalent. Mopar DOT 3 and SAE J1703 should be used. Use only recommended brake fluids.
Page 415 MAINTENANCE SCHEDULES CONTENTS Emission Control System Maintenance ..416 Maintenance Schedules ....416 Schedule “B” ......419 Schedule “A”...
Page 416: Emission Control System Maintenance
416 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
Page 417 • Taxi, police, or delivery service (commercial ser- vice). • Off-road or desert operation. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the Maintenance Schedules section of this manual.
Page 418 418 MAINTENANCE SCHEDULES Once a Month • Check tire pressure and look for unusual wear or damage. • Inspect the battery and clean and tighten the terminals as required. • Check the fluid levels of coolant bottle, brake master cylinder and transmission, add as needed. •...
Page 419: Schedule "B" 419
SCHEDULE “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. Change the automatic transmission fluid and filter every 60,000 miles (96 000 km) if the vehicle is usually operated under one or more of the conditions marked with an •...
Page 420 420 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. * Change the All Wheel Drive (AWD) power transfer unit fluid.
Page 421 Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front & Rear) Inspect the PCV valve and replace as necessary.* Change the All Wheel Drive (AWD) power...
Page 422 422 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. * Change the All Wheel Drive power transfer unit fluid.
Page 423 Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front & Rear) Inspect the PCV valve and replace if necessary.* Inspect the serpentine drive belt, replace if necessary.
Page 424 424 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter Replace the spark plugs. Inspect the tie rod ends and boot seals. (Front & Rear) Check the PCV valve and replace if necessary.
Page 425 Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter * Replace engine timing belt. Change the All Wheel Drive (AWD) power transfer unit fluid.
Page 426 426 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if neces- sary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front & Rear) Inspect the PCV valve and replace as necessary.* Inspect the serpentine drive belt, replace if neces-...
Page 427 Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if neces- sary. * Replace the engine air cleaner filter. Inspect the serpentine drive belt, replace if neces- sary.
Page 428 428 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if neces- sary. * Replace the engine air cleaner filter. Replace the spark plugs. Inspect the serpentine drive belt, replace if neces- sary.
Page 429 Miles (Kilometers) Change the All Wheel Drive (AWD) rear carrier fluid. (See note at the end of this chart) Replace the air conditioning filter. * This maintenance is recommended by the manufacture to the owner but is not required to maintain the emis- sions warranty.
Page 430: Schedule "A
430 SCHEDULE “A” SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front &...
Page 431 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front &...
Page 432 432 SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if neces- sary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front & Rear) Check and replace the PCV valve , if necessary.* Inspect the serpentine drive belt, replace if neces-...
Page 433 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Replace engine timing belt. Inspect the tie rod ends and boot seals. (Front & Rear) Check the PCV valve and replace, if necessary.* Inspect the serpentine drive belt, replace if necessary.
Page 434 434 SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if neces- sary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front & Rear) Check the PCV valve and replace, if necessary.* Inspect the serpentine drive belt, replace if necessary.
Page 435 WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.
Page 437: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle ......438 Prepare For The Appointment .
Page 438: Suggestions For Obtaining Service For Your Vehicle
We want you to be happy with our products and services. Warranty service must be done by an authorized Chrysler, Dodge, or Jeep dealer. We strongly recommend that you take your vehicle to your selling dealer. They know you and your vehicle best, and are most concerned that you get prompt and high quality service.
Page 439 technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. •...
Page 440 440 IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommuni- cation Devices for the Deaf) equipment at its Customer Center. Any hearing or speech impaired customer who has access to a TDD or a conventional teletypewriter (TTY) in the United States can communicate with the manufacturer by dialing 1–800–380–CHRY.
Page 441: Warranty Information (U.s. Vehicles Only)
WARRANTY INFORMATION (U.S. Vehicles Only) See the Warranty Information Booklet for the terms and provisions of DaimlerChrysler’s warranties applicable to this vehicle. MOPAR PARTS Mopar fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best.
Page 442: Publication Order Forms
• Owner’s Manuals. These manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific Chrysler group vehicles. Included are starting, operating, emergency and maintenance pro- cedures as well as specifications, capabilities and safety tips.
Page 443: Department Of Transportation Uniform Tire Quality Grades
Call Toll Free at: • 1–800–890–4038 (U.S.) • 1–800–387–1143 (Canada) Visit us on the World Wide Web at: • www.techauthority.daimlerchrysler.com • www.daimlerchrysler.ca/manuals DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories estab- lished by the National highway Traffic Safety Adminis- tration.
Page 444: Temperature Grades
444 IF YOU NEED CONSUMER ASSISTANCE WARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory...
Page 445 INDEX...
Page 446 446 INDEX Adding Fuel ......321 Adding Washer Fluid ....140,382 Additives, Fuel .
Page 447 Selection Of Lubricant ....392,413 Shifting ......272 Special Additives .
Page 448 448 INDEX Radiator (Coolant Pressure) ....386 Car Washes ......397 Carbon Monoxide Warning .
Page 449 Coolant Pressure Cap (Radiator Cap) ..386 Cooling System ......383 Adding Coolant (Antifreeze) .
Page 450 450 INDEX Driving On Slippery Surfaces ....287 DVD Player (Video Entertainment System) ..221 E-85 Fuel .
Page 451 Exhaust System ......382 Extender, Seat Belt ......49 Exterior Folding Mirrors .
Page 452 452 INDEX Filler Cap (Gas Cap) ....321 Gasoline ......318 Gauge .
Page 453 Replacing ......406 Switch ......135 Time Delay .
Page 454 454 INDEX Key-In Reminder ......14 Keyless Entry System ..... . 20 Keys .
Page 455 Oil Pressure ......186 Park ....... 408 Reading .
Page 456 456 INDEX Mirrors ....... . 88 Automatic Dimming ..... 88 Electric Remote .
Page 457 Owner’s Manual (Operator Manual) ..442 Panic Alarm ......24 Parking Brake .
Page 458 458 INDEX Rear Camera ......146 Rear Liftgate ......35 Rear Seating Flexibility .
Page 459 Adjustable Shoulder Belt ....46 Adjustable Upper Shoulder Anchorage ..46 And Pregnant Women ....49 Child Restraint .
Page 460 460 INDEX Engine Fails to Start ....268 Starting and Operating ....266 Starting Procedures .
Page 461 Compact Spare ......301 General Information ....297 High Speed .
Page 462 462 INDEX Overdrive ......274 Selection of Lubricant ....392,413 Transmission .
Page 463 Washers, Windshield ..... 138 Washing Vehicle ......397 Wheel Alignment and Balance .
Page 464 NOTES...

Chrysler 2007 Pacifica Instruction Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

Quick Links

INTRODUCTION

Chapters

Related Manuals for Chrysler 2007 Pacifica

Summary of Contents for Chrysler 2007 Pacifica