Advertisement
Quick Links
Model F482A22
4-channel, line-powered, ICP® sensor signal cond., unity gain, BNC
Installation and Operating Manual
For assistance with the operation of this product,
contact PCB Piezotronics, Inc.
Toll-free: 800-828-8840
24-hour SensorLine: 716-684-0001
Fax: 716-684-0987
E-mail: info@pcb.com
Web: www.pcb.com
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for PCB Piezotronics F482A22
Summary of Contents for PCB Piezotronics F482A22
- Page 1 Model F482A22 4-channel, line-powered, ICP® sensor signal cond., unity gain, BNC Installation and Operating Manual For assistance with the operation of this product, contact PCB Piezotronics, Inc. Toll-free: 800-828-8840 24-hour SensorLine: 716-684-0001 Fax: 716-684-0987 E-mail: info@pcb.com Web: www.pcb.com...
- Page 2 Piezotronics, user servicing or repair is critical test. not recommended and, if attempted, may void the factory warranty. Routine PCB Piezotronics maintains an ISO- maintenance, such as the cleaning of 9001 certified metrology laboratory and electrical connectors, housings, and offers calibration services, which are...
- Page 3 E-mail: info@pcb.com representative. Warranty – All equipment and repair services provided by PCB Piezotronics, Inc. are covered by a limited warranty against defective material workmanship for a period of one year from date of original purchase. Contact...
-
Page 4: China Rohs Compliance
PCB工业监视和测量设备 - 中国RoHS2公布表 PCB Industrial Monitoring and Measuring Equipment - China RoHS 2 Disclosure Table 有害物质 汞 镉 六价铬 (Cr(VI)) 多溴联苯 (PBB) 多溴二苯醚 (PBDE) 部件名称 铅 (Pb) (Hg) (Cd) 住房 PCB板 电气连接器 压电晶体 环氧 铁氟龙 电子 厚膜基板 电线 电缆 塑料 焊接... - Page 5 Component Name Hazardous Substances Lead Mercury Cadmium Chromium VI Polybrominated Polybrominated (Pb) (Hg) (Cd) Compounds Biphenyls Diphenyl (Cr(VI)) (PBB) Ethers (PBDE) Housing PCB Board Electrical Connectors Piezoelectric Crystals Epoxy Teflon Electronics Thick Film Substrate Wires Cables Plastic Solder Copper Alloy/Brass This table is prepared in accordance with the provisions of SJ/T 11364.
- Page 6 WARNING 2: This equipment is designed with user safety in mind; however, the protection provided by the equipment may be impaired if the equipment is used in a manner not specified by PCB Piezotronics, Inc. Caution 1: Cables can kill your equipment. High voltage electrostatic discharge can damage electrical devices. Similar to a capacitor, a cable can hold a charge caused by triboelectric transfer, such as that which occurs in the following: ...
- Page 7 MODEL 482A22 LINE POWERED SIGNAL CONDITIONER 1.2 Introduction ® Model 482A22 is a four-channel, line-operated signal conditioner for ICP transducer systems. This unit provides constant current excitation to the built-in transducer amplifier and decouples the signal from the DC bias voltage. The unit also contains provision for fault monitoring the channel, as well as provision for externally varying the constant current output over a 2 to 20 mA range.
- Page 8 MODEL 482A22 LINE POWERED SIGNAL CONDITIONER Figure 2: Fault Monitor Table ® When an ICP transducer (or in-line amplifier) is connected to the INPUT jack, the front monitor meter indicates approximately midscale (green) if the transducer or amplifier is functioning properly. It does not read midscale if the transducer bias is 3 to 5 volts.
- Page 9 MODEL 482A22 LINE POWERED SIGNAL CONDITIONER CURRENT ADJUST Figure 3: Constant Current Adjust 5.0 Maintenance and Repair Because of the sophisticated nature of PCB instrumentation, field repair of the equipment is not recommended. Most PCB signal conditioners are of modular construction and are factory repairable. A repair or replacement quotation is available at no charge.
- Page 10 MODEL 482A22 LINE POWERED SIGNAL CONDITIONER 482A21 and 482A22 Troubleshooting Guide Problem Test/Solution Unit does not appear to be powered - Power switch in the on position. - Test ‘sensor’ excitation current. Measure the current on the ‘sensor’ input up/ No meter movement. BNC from the center conductor to the shell.
- Page 11 Model Number Revision: K SENSOR SIGNAL CONDITIONER ECN #: 43617 482A22 Performance ENGLISH OPTIONAL VERSIONS Channels Optional versions have identical specifications and accessories as listed for the standard Voltage Gain(± 1 %) model except where noted below. More than one option may be used. Low Frequency Response(-5 %) <0.1 Hz <0.1 Hz...
Need help?
Do you have a question about the F482A22 and is the answer not in the manual?
Questions and answers