Page 1: Introduction
TABLE OF CONTENTS SECTION ............. 3 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 3: Table Of Contents
CONTENTS Introduction ......4 How To Use This Manual ....4 Warnings And Cautions .
Page 4: Introduction
4 INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully.
Page 5 INTRODUCTION 5...
Page 6: Vehicle Identification Number
The vehicle identification number (VIN) is found on the left front corner of the instrument panel, visible from outside of the vehicle through the windshield. This number also appears on the Automobile Information Vehicle Identification Number Disclosure Label affixed to a window on your vehicle.
Page 7: Vehicle Modifications / Alterations
INTRODUCTION 7 VEHICLE MODIFICATIONS / ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 9 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 Ignition Key Removal ....12 Key-In-Ignition Reminder .
Page 10 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Vehicle Theft Alarm — If Equipped ...27 Sliding Side Door ......30 Sliding Door Open Flash .
Page 11: Things To Know Before Starting Your Vehicle
Engine Break-In Recommendations ...82 Safety Tips ......83 Exhaust Gas .
Page 12: Things To Know Before Starting Your Vehicle 9
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Vehicle Key You can insert the double sided keys into the locks with either side up. The dealer that sold you your new vehicle has the key code numbers for your vehicle locks.
Page 13: Key-In-Ignition Reminder
The power window switches, radio, power NOTE: outlets, and removable console (if equipped), will remain active for up to 45 seconds after the ignition switch has been turned off. Opening a vehicle front door will cancel this feature. WARNING! Leaving children in a vehicle unattended is danger- ous for a number of reasons.
Page 14 14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE chip (transponder) embedded into them. Only keys that have been programmed to the vehicle can be used to start and operate the vehicle. The Sentry Key Immobilizer System does not need to be armed or activated.
Page 15: Replacement Keys
All of the keys provided with your new vehicle have been programmed to the vehicle electronics. Replacement Keys NOTE: Only keys that have been programmed to the vehicle electronics can be used to start the vehicle. Once a Sentry Key has been programmed to a vehicle, it can not be programmed to any other vehicle.
Page 16: General Information
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Insert a blank Sentry Key into the ignition switch and turn the ignition switch ON within 60 seconds. After 10 seconds a single chime will sound. The Theft Alarm Light will stop flashing, turn on for 3 seconds; then turn off. The new Sentry Key has been programmed.
Page 17: Door Locks
NOTE: • The front courtesy overhead console, door courtesy and liftgate lights do not turn on if the dimmer control is in the interior lights ON position (extreme top position). • The illuminated entry system will not operate if the dimmer control is in the “defeat”...
Page 18: Power Door Locks - If Equipped
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • For personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle. • When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle.
Page 19 locks will not operate. This prevents you from acciden- tally locking your keys in the vehicle. Removing the key or closing the door will allow the locks to operate. A chime will sound if the key is in the ignition switch and a door is open, as a reminder to remove the key.
Page 20: Remote Keyless Entry - If Equipped
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Unlock On Exit— If Equipped The doors will unlock automatically on vehicles with power door locks if: 1. The Auto Door Locks feature is enabled and the Auto Unlock On Exit feature is enabled, 2.
Page 21 Three button transmitters will provide basic UNLOCK, LOCK and PANIC functions. Three Button Transmitter Six button transmitters will provide functions that allow the same basic operation as the three button, but may also be used to Open/Close the optional power liftgate, left power sliding door, or right power sliding door.
Page 22: To Unlock The Doors And Liftgate
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To unlock the doors and liftgate: Press and release the UNLOCK button on the transmitter once to unlock the driver’s door side of the vehicle, or twice to unlock all doors and liftgate. The illuminated entry system also turns on.
Page 23: Using The Panic Alarm
Using The Panic Alarm: To turn the panic alarm feature ON or OFF, press and hold the PANIC button on the transmitter for at least one second and release. When the panic alarm is on, the headlights and park lights will flash, the horn will pulse on and off and the interior lights will turn on.
Page 24 24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Open/Close Left Power Sliding Door — If Equipped Press the LEFT button twice within five seconds to open/close the left power sliding door. If the button is pushed while the door is being power closed, the door will reverse to the full open position.
Page 25 To Turn Off “Flash Lights On Lock/Unlock” — If Equipped If desired, the “Flash Lights On Lock/Unlock” feature can be turned on and off by performing the following procedure: 1. Press the LOCK button for 5 to 10 seconds. 2. While the LOCK button is pressed, (after 5 seconds) press the UNLOCK button.
Page 26: General Information
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. •...
Page 27: Vehicle Theft Alarm - If Equipped
Separating transmitter halves 2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 3.
Page 28 28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To arm the system: Remove the key from the ignition switch and either: 1. Press a power door lock button while the driver’s or passenger’s door is open. 2. Press the LOCK button on the keyless entry transmit- ter.
Page 29 • The system remains armed during liftgate entry, press- ing the liftgate button will not disarm the system, if someone enters the vehicle through the liftgate and opens any door the alarm will sound. • When the system is armed, the doors can not be unlocked from the interior power door lock switches.
Page 30: Sliding Side Door
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SLIDING SIDE DOOR The sliding door may be opened from the inside or the outside. Pull out on the outside handle to open the sliding door from the outside. To open the sliding door from the inside, press the button on the grab handle and open the door.
Page 31: Sliding Door Open Flash
NOTE: The driver’s side sliding door cannot be opened while the fuel door is open. This feature operates only when the sliding door is fully closed prior to opening the fuel door. Sliding Door Open Flash When the sliding door(s) are opened, the left and right exterior hazard lights will flash for 12 seconds to alert other drivers in the area that passenger(s) could be entering or exiting the vehicle.
Page 32 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The power sliding door may also be opened by pressing the switches on the overhead console or the switch located on the trim panel just in front of the sliding door. To keep your door operating properly, observe the fol- lowing guidelines.
Page 33 If the inside or outside door handles are used while the power sliding door is activated, the power sliding door feature will be canceled and the door must be opened or closed manually. To avoid unintentional operation of the power sliding door from the rear seats, press the button located in the overhead console to disable the switches for the rear seat passengers.
Page 34: Child Protection Door Lock
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Protection Door Lock To provide a safer environment for small children riding in the rear seats, the sliding doors are equipped with a child protection door lock system. WARNING! To avoid trapping anyone in the vehicle in a colli- sion.
Page 35: Liftgate
When the child lock system is engaged the door can be opened only by using the outside door handle, remote keyless entry transmitter, switches on the overhead con- sole or the switches located on the trim panel just in front of the power sliding door, even though the inside door lock is in the unlocked position.
Page 36: Power Liftgate - If Equipped
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Once unlocked, on vehicles equipped with power locks, the liftgate can be opened or closed without using the key. To open the liftgate, depress the liftgate release switch located on the underside of the license plate bar and pull the liftgate open with one fluid motion.
Page 37 The power liftgate may also be opened by pressing the button located on the overhead console. Power Liftgate Switch When the remote keyless entry transmitter button is pressed and the “Lamp Flash” feature is enabled, the tail lights will flash to signal that the liftgate is opening or closing.
Page 38 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The power liftgate must be in the full open or close positions for any of the buttons to operate. If the liftgate is not in the full open or close positions it must be opened or closed manually.
Page 39: Windows
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 Gas props support the liftgate in the open position. However, because the gas pressure drops with tempera- ture, it may be necessary to assist the props when opening the liftgate in cold weather. WINDOWS Power Vent Windows Switches on the driver’s door trim panel let the driver...
Page 40: Power Windows
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Windows You can control either front window using switches on the driver’s door trim panel. There is a single switch on the passenger’s door trim panel which operates the passenger door window. The switches will operate only when the ignition switch is in the ON or ACCESSORY position.
Page 41 Auto Down Feature — If Equipped The driver’s window switch has an auto down feature. Press the window switch past the detent, release, and the window will go down automatically. To open the window part way, press the window switch part way and release it when you want the window to stop.
Page 42: Occupant Restraints
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems. These include the front and rear seat belts for the driver and all passengers, front airbags for both the driver and front passenger, driver inflatable knee blocker and if equipped, window bags for the driver and passengers seated next to a window.
Page 43: Lap/Shoulder Belts
WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buck- led up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle.
Page 44 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. •...
Page 45 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is near the seatback of the front seats and next to your arm in the rear seats. Grasp the latch plate and pull out the belt.
Page 46 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click”. Latch Plate To Buckle WARNING! • A belt that is buckled into the wrong buckle will not protect you properly.
Page 47 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision.
Page 48 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection.
Page 49: Lap/Shoulder Belt Untwisting Procedure
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position.
Page 50 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180° to create a fold that begins immediately above the latch plate. Creating A Fold 3.
Page 51: Center Lap Belts
Center Lap Belts The center seating positions have a lap belt only. To fasten the lap belt, slide the latch plate into the buckle until you hear a “click”. To lengthen the lap belt, tilt the latch plate and pull. To remove slack, pull the loose end of the webbing.
Page 52: Enhanced Driver Seat Belt Use Reminder System (Beltalert)
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: These devices are not a substitute for proper seat belt placement by the occupant. The seat belt still must be worn snugly and positioned properly. The pretensioners are triggered by the front airbag con- trol module (see Front Airbag Section).
Page 53: Seat Belts And Pregnant Women
2. Turn the ignition key to the RUN position (engine does not need to be running), and wait for the Seat Belt Warning Light to turn off. 3. Within 60 seconds, unbuckle and then re-buckle the driver’s seat belt at least three times, ending with the seat belt buckled.
Page 54: Driver And Front Passenger Supplemental Restraint Systems (Srs) - Airbags
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions.
Page 55 Also, the front passenger airbag is certified to the Federal regulations that define Occupant Classification (Refer to “Occupant Classification System” in this section). This vehicle may also be equipped with a driver inflat- able knee blocker located on the instrument panel below the steering column.
Page 56 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not put anything on or around the airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers for the airbag cushions are designed to open only when the airbags are inflating.
Page 57 Here are some simple steps you can take to minimize the risk of harm from a deploying airbag. 1. Children 12 years old and under should always ride buckled up in a rear seat. Infants in rear facing child restraints should NEVER ride in the front seat of a vehicle with a passenger front airbag.
Page 58 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags.
Page 59 • Knee Impact Bolster • Driver Inflatable Knee Blocker • Front Passenger Seat Occupant Classification System (OCS) — If Equipped − Occupant Classification Module − Passenger Airbag Disabled (PAD) Indicator Light − Interconnecting Wiring − Bladder Assembly − Belt Tension Sensor How The Airbag System Works •...
Page 60 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE first turned on. After the self-check, the AIRBAG warning light will turn off. The PAD indicator light will function normally (Refer to “Passenger Airbag Disable (PAD) Indicator Light” in this section). If the ORC detects a malfunction in any part of the system, it turns on the AIRBAG warning light either momen- tarily or continuously.
Page 61 • The Side Impact SRS Window Bags are designed to activate only in certain side collisions. When the ORC and the side impact sensors (with side impact option) detects a collision requiring the window bags to inflate, it signals the inflators on the crash side of the vehicle.
Page 62 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If your vehicle contains a Passenger Airbag Disable indicator light, it will be equipped with the Occupant Classification System (OCS). The OCS system will classify an occupant into a size category based on sensor readings from within the seat cushion.
Page 63 OFF when the OCS has determined that the occupant size category is a child. Also, when the seat is empty or an object that weighs less than a predetermined threshold is placed on the seat, the light will remain OFF. (The PAD indicator light is an amber light located on the center of the instrument panel above the radio.) Passenger Airbag Disabled Light...
Page 64 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Occupant Classification Module (OCM) — If Equipped is located beneath the front passenger seat. The OCM classifies the occupant into one of three size categories based on the input from the Bladder Assem- bly and Belt Tension Sensor.
Page 65 (OCS) to properly classify the front passenger and calcu- late the proper airbag deployment. Do not make any modifications to the front passenger seat components, assembly, or to the seat cover. WARNING! Unapproved modifications or service procedures to the front passenger seat assembly, its related compo- nents, or seat cover may inadvertently change the airbag deployment in case of a frontal crash.
Page 66 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • At no time should any supplemental restraint system (SRS) component or SRS related component or fas- tener be modified or replaced with any part except those which are approved by DaimlerChrysler/ Mopar.
Page 67 • It is not advisable to drive your vehicle after the airbags have deployed. If you are involved in another collision, the airbags will not be in place to protect you. WARNING! Deployed airbags, seat belt pretensioners and driver inflatable knee blocker cannot protect you in an- other collision.
Page 68 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured because the airbags are not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel.
Page 69: Daimlerchrysler Corporation Integrated Child Seat - If Equipped
• The light remains on or flickers after the 6 to 8 second interval. • The light flickers or comes on and remains on while driving. DaimlerChrysler Corporation Integrated Child Seat — If Equipped Operating instructions for this seat are included with the seat.
Page 70 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.
Page 71 infant carriers do, so they can be used rearward-facing by children who weigh more than 20 lbs (9 kg) but are less than one year old. • Rearward-facing child seats must NEVER be used in the front seat of a vehicle with a front passenger airbag.
Page 72 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Check belt fit periodically. A child’s squirming or slouching can move the belt out of position. • If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. If this doesn’t help, move the child to the center rear seating position and use the lap belt.
Page 73 Here are some tips on getting the most out of your child restraint: • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. We also recommend that you make sure that you can install the child restraint in the vehicle where you will use it, before you buy it.
Page 74 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Buckle the child into the seat according to the child restraint manufacturer’s directions. • When your child restraint is not in use, secure it in the vehicle with the seat belt or remove it from the vehicle. Don’t leave it loose in the vehicle.
Page 75 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 head restraint posts. Except for bench seats with split seatbacks, when the tether anchorage is used in the center seating position, the strap should be positioned straight over the top of the seatback. For bench seats with split seatbacks, route the tether between the seatbacks.
Page 76 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap.
Page 77 at one time. Instead, you may install one child restraint at the center position, or one child restraint at each of the right and left positions. WARNING! Fleet Vehicles Only: Do not install child restraint systems equipped with LATCH attachments at all three seating positions in the seat at one time.
Page 78: Rear Seat Delete Feature (Commercial Vehicles Only) - If Equipped
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
Page 79: Restraining Infants And Small Children With Seat Delete Feature (Commercial Vehicles Only)
WARNING! Rear Facing Infant restraints must never be secured in the passenger seat of a vehicle with a passenger airbag. In an accident a passenger airbag may deploy causing severe injury or death to infants riding in rear facing infant restraints. Restraining Infants and Small Children with Seat Delete Feature (Commercial Vehicles Only) There are different sizes and types of restraints for...
Page 80 80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE child restraints or belt-positioning booster seats should ride properly buckled in the passenger seat with the seat adjusted to the rear most position. Never allow children to slide the shoulder belt behind them or under their arm.
Page 81 Tether To Anchor 3. Follow the child restraint manufacturer’s directions for proper use of connecting the child restraint to the extended tether strap. 4. If necessary, raise the passenger seat head restraint to allow the tether strap to be routed under the head restraint.
Page 82: Engine Break-In Recommendations
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. Using the hook attached to the child restraint tether strap, attach the child restraint tether strap to the metal ring on the vehicle tether anchor. 7. Following the child seat manufacturer’s instructions, tighten the child restraint tether strap.
Page 83: Safety Tips
While cruising, brief full-throttle acceleration, within the limits of local traffic laws, contributes to a good break-in. Wide open throttle acceleration in low gear can be detrimental and should be avoided. The engine oil installed in the engine at the factory is a high quality energy conserving type lubricant.
Page 84: Inside The Vehicle
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! If you are required to drive with the deck lid/liftgate open, make sure that all windows are closed, and the climate control blower switch is set at high speed. DO NOT use the recirculation mode. Safety Checks You Should Make Inside The Vehicle Seat Belts...
Page 85: Periodic Safety Checks You Should Make Outside
Periodic Safety Checks You Should Make Outside The Vehicle Tires Examine tires for excessive tread wear or uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect tread and sidewall for cuts or cracks. Check wheel nuts for tightness, and tires (includ- ing spare) for proper pressure.
Page 87: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors .......92 Inside Day/Night Mirror ....92 Automatic Dimming Mirror —...
Page 88 88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Seats ....... . 108 Manual Front &...
Page 89 Lights ....... 138 Interior Lights ..... . . 138 Park Lights .
Page 90 90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Accelerate For Passing ....153 Overhead Console — If Equipped ... 154 Courtesy/Reading Lights .
Page 91 Storage ......177 Front Seat Storage Bin — If Equipped ..177 Second Row Seat Storage Bins —...
Page 92: Mirrors
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror Adjust the mirror to center on the view through the rear window. A two point pivot system allows for horizontal and vertical adjustment of the mirror. Adjusting Rearview Mirror Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle).
Page 93: Driver's Side Outside Mirror Auto Dimmer - If Equipped
Automatic Dimming Mirror UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Driver’s Side Outside Mirror Auto Dimmer —...
Page 94: Outside Mirror - Driver's Side
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirror — Driver’s Side Adjust the outside mirror to center on the adjacent lane of traffic, with a slight overlap of the view obtained on the inside mirror. Outside Mirror — Passenger’s Side Adjust the convex outside mirror so you can just see the side of your vehicle in the portion of the mirror closest to the vehicle.
Page 95: Heated Remote Control Mirrors - If Equipped
Power Mirror Switches Select a mirror and press one of the four arrows for the direction you want the mirror to move. Driver’s power mirror preselected positions can be con- trolled by the optional Memory Seat Feature. Refer to the Memory Seat paragraph in section 3 of this manual.
Page 96: Hands-Free Communication (Uconnect™) - If Equipped
UConnect™ works no matter where you stow your cellular phone (be it your purse, pocket, or briefcase). UConnect™ allows up to seven cellular phones to be linked to the system, and it is available in (www.chrysler.com/ English, French, or Spanish formats (as equipped).
Page 97: Operation
The rearview mirror contains the microphone for the system and the control buttons that will enable you to access the system. The diagram below shows the mirror with the appropriate buttons. Individual button behavior is discussed in the “Operation” Section. UConnect™...
Page 98 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • You can say Dial at the Ready prompt. When prompted for the phone number you wish to dial, say the phone number ( 123 456 7890 ). • Alternatively as you become familiar with the UCon- nect™...
Page 99 system will use the priority 3 cellular phone when you make a call. You can select to use a lower priority cellular phone at any time. Making a Phone Call Using Digit Dialing • Press the ’Phone’ button to begin. •...
Page 100 100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The UConnect™ system will allow you to enter up to 32 names into the phonebook with each name having up to four associated phone numbers and designations. Edit Entries in the UConnect™ Phonebook •...
Page 101: Phone Call Features
• After you enter the name, the UConnect™ system will ask you if you wish to delete the home, work, mobile, or pager number for this entry. Delete All Entries in the UConnect™ Phonebook • Press the ’Phone’ button to begin. •...
Page 102 102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Answer or Reject an Incoming Call - No Call Currently in Progress When you receive a call on your cellular phone, the UConnect™ system will interrupt the stereo audio and will ask if you would like to answer the call by pressing the ’Phone’...
Page 103: Advanced Phone Connectivity
Conference Call When two calls are in progress (one active and one on hold), press the ’Phone’ button until you hear a double beep indicating that the two calls have been joined into one conference call. Three-Way Calling To initiate three-way calling, press the ’Voice Recogni- tion’...
Page 104 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Delete Paired Cellular Phones • Press the ’Phone’ button to begin. • After the Ready prompt, say Setup Phone Pairing . • At the next prompt, say Delete . • You will be asked to say the name of the phone that you wish to delete.
Page 105: Uconnect™ System Features
Select a Lower Priority Paired Cellular Phone • Press the ’Phone’ button to begin. • After the Ready prompt, say Setup Select Phone . • When prompted, say the phone name of the cellular phone you wish to use, or say List Phones to hear a list of all the phones that have been paired to your UConnect™...
Page 106 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Barge In - Overriding Prompts The ’Voice Recognition’ button can be used when you wish to skip part of a prompt and issue your voice recognition command immediately. For example, if a prompt is playing Would you like to pair a phone, clear a , you could press the ’Voice Recognition’...
Page 107 Dialing Using the Cellular Phone Keypad You can dial a phone number with your cellular phone keypad and still use the UConnect™ system. By dialing a number with your paired Bluetooth™ cellular phone, the audio will be played through your vehicle’s stereo sys- tem.
Page 108: Seats
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE SEATS Manual Front & Second Row Seat Adjuster The adjusting bar is located under the front of the seat. Pull the bar up and move the seat to the desired position. Release the bar to lock the seat into position. Manual Seat Adjuster Using body pressure, move forward and rearward on the seat to be sure the seat adjusters have latched.
Page 109: 8-Way Driver's Power Seat - If Equipped
8–Way Driver’s Power Seat — If Equipped The driver’s power seat switches are located on the outboard side of the seat. The front switch controls up/down, forward/rearward, and tilt adjustment. The rear switch controls the seatback recline adjustment. Driver Power Seat Switch UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 4–Way Passenger’s Power Seat —...
Page 110: Adjustable Head Restraints - If Equipped
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjustable Head Restraints — If Equipped Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Pull up or push down on the head restraint so that the upper edge is as high as practical.
Page 111: Heated Seats - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Heated Seats — If Equipped This feature heats the front driver and passenger seats. The controls for the heated seats are located on the instrument panel above the radio. You may choose LOW, HIGH or No Heat.
Page 112: Manual Reclining Seats - If Equipped
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Reclining Seats — If Equipped The recliner mechanism control is on the outboard side of the seat. To recline, lean forward slightly, lift the lever, then push back to the desired position and release the lever.
Page 113: Manual Lumbar - If Equipped
WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or fatally injured. Use the recliner only when the vehicle is parked.
Page 114 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Fold Second Row Seats 1. Move the front seat fully forward, lower the head restraint and raise the armrests on the second row seat. 2. Pull up on the storage bin latch to open cover. Storage Bin Cover 3.
Page 115 4. Pull rearward on the release strap located at the rear of the seat and tumble the seat forward into the storage bin. Seat Release Strap 5. Close the storage bin cover. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 To Unfold Second Row Seats 1.
Page 116 116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Pull up on the seatback recliner lever located on the outboard side of the seat, to return the seatback to its full upright position. Seatback Release Lever 4. Close the storage bin cover and adjust the head restraint to the desired position.
Page 117 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 3. Pull release strap marked “2” to release the anchors. 4. Pull release strap marked “3” and tumble the seat rearward into the storage bin. Release Strap 2 Release Strap 3...
Page 118 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Unfold Third Row Seats 1. Pull up on the assist strap to lift the seat out of the storage bin and push the seat forward until the anchors latch. Assist Strap 2. Pull release strap marked “1” to unlock the recliner. 3.
Page 119 WARNING! In a collision, you or others in your vehicle could be injured if seats are not properly latched to their floor attachments. Always be sure the seats are fully latched. Tailgate Mode 1. Pull release strap “2”, then pull release strap “3” to rotate the entire seat rearward.
Page 120: Easy Access Seating
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. To restore the seat to its upright position, lift up on the seatback and push forward until the anchors latch. WARNING! To avoid serious injury or death, never operate the vehicle with occupants in the third row seat, while in the tailgate mode.
Page 121: Middle Quad Fold & Tumble Seat Removal
To tilt the seat on vehicles equipped with fold-in-floor seating, pull forward on the release strap located on the front of the seat between the seat back and seat cushion and tilt the seat fully forward. To return the seat, lower the seat and ensure that it is fully latched.
Page 122 122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Pull up on the seatback release lever located on the outboard side of the seat and fold the seatback down. If the head restraint contacts the rear of the front seat, move the front seat forward on its tracks.
Page 123 5. Pull the release bar located at the bottom front edge of the seat to disengage the front attachments. Release Bar Location 6. The seat assembly can now be removed from the vehicle and moved on its Easy Out Rollers. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 To reinstall the seat, remove any obstructions from the floor in front of the seat and ensure the head restraint is...
Page 124: 50/50 Fold & Tumble Rear Seat Removal
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 50/50 Fold & Tumble Rear Seat Removal 1. Lower the head restraint and pull up on release lever “1” to fold the seatback down. Release Lever Location 2. Pull up on release lever “2” and tumble the seat fully forward.
Page 125 3. Pull the release strap “3” located at the bottom of the seat to disengage the front attachments. Release Strap Location UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 4. The seat assembly can now be removed from the vehicle and moved on its Easy Out Rollers. To reinstall the 50/50 rear seat, lower the head restraint to the full down position, tilt the seat forward and engage the front floor attachments, then tilt the seat rearward to...
Page 126: Passenger Bench Seats
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3 – Passenger Bench Seats Release levers are located on the rear leg assemblies, near the floor. To remove the seat, squeeze each release handle and rotate downwards to deploy the wheels. A lock indicator button pops up when the seat is unlocked.
Page 127: Plastic Grocery Bag Retainer
WARNING! If not properly latched, the bench seats could be- come loose. Personal injuries could result. After reinstalling these seats, be sure the red indicator button on the release handles return into the handles. Plastic Grocery Bag Retainer Retainer hooks which will hold plastic grocery bag handles are built into the seatbacks of all rear seats and some front seats.
Page 128: Rear-Most Bench Seat
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear-Most Bench Seat The seat position can be adjusted fore and aft to any of three positions - normal (rearward), intermediate, and full forward. In this way varying needs for legroom and cargo space behind the seat can be accommodated. Release Lever Location The release lever is below the seat and is accessible from the front and back of the seat.
Page 129 1. Normal Seating— The 2nd and 3rd row seats are installed. The 3rd row bench seat is in the full rear position on the tracks. 2. Increased Storage— Increased storage area is provided by adjusting 3rd row bench seat to the intermediate track position. Rear seat- ing for 3 passengers (children) is still provided.
Page 130: Rear Quad And 50/50 Seating Flexibility
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Auxiliary Seating— The middle quad seats are removed from the vehicle. The 3– passenger bench seat can be installed in either the second or third row. Rear Quad and 50/50 Seating Flexibility The seats may be used with either or both seatbacks folded forward for additional storage space, or with either or both seats removed from the vehicle.
Page 131 NOTE: Driving with the 2nd-row seats in the tumbled position is not recommended when passengers occupy the 3rd row seats. This position is intended only to increase available cargo area without requiring removal of the seats. Do not leave the head restraint stored between the cushions for extended periods of time or inadvertent damage to the seat cover or head restraint may occur.
Page 132: Driver Memory System - If Equipped
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Not all head restraints in this vehicle are the same. Head restraints from one seating position should not be removed and installed in any other seating posi- tion. In a collision, serious injury or death may result if the proper head restraint is not installed on each seat.
Page 133: Setting Memory Positions And Linking Remote
Driver Memory Switches Your vehicle may have been delivered with two Remote Keyless Entry transmitters. One or both transmitters can be linked to either memory position. The memory system can accommodate up to four transmitters, each one linked to either of the two memory positions. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 Setting Memory Positions and Linking Remote Keyless Entry Transmitter to Memory...
Page 134: Memory Position Recall
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Turn on the radio and set the radio station presets (up to 10 AM and 10 FM stations can be set). 6. Turn the ignition switch to the OFF position and remove the key. 7.
Page 135: To Disable A Transmitter Linked To Memory
To recall the memory settings for driver one, press memory button number 1 on the driver’s door or the Unlock button on the Remote Keyless Entry transmitter linked to memory position 1. To recall the memory setting for driver two, press memory button number 2 on the driver’s door or the Unlock button on the Remote Keyless Entry transmitter linked to memory position 2.
Page 136: To Open And Close The Hood
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To disable another transmitter linked to either memory position, repeat steps 1-5 for each transmitter. NOTE: Once programmed, all transmitters linked to memory can be easily enabled or disabled at one time. Refer to the Remote Linked to Memory Customer Pro- grammable Features in the Electronic Vehicle Informa- tion Center (EVIC) for more information.
Page 137 Next, push to the left the safety catch located under the front edge of the hood, near the center. Hood Safety Catch Use the hood prop rod to secure the hood in the open position. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 To prevent possible damage, do not slam the hood to close it.
Page 138: Lights
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS All of the lights, except the hazard warning lights, are controlled by switches to the left of the steering column on the instrument panel. Headlight Switch Interior Lights Interior lights are turned on when a door or liftgate is opened, the keyless entry transmitter is activated, or when the dimmer control is moved to the extreme top.
Page 139: Park Lights
Park Lights Turn this switch to the first detent to turn the park lights on. This also turns on all instrument panel lighting. Headlights Turn the headlight switch to the 2nd detent to turn the headlights and park lights on. This also turns on all instrument panel lighting.
Page 140: Automatic Headlights - If Equipped
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior light Defeat (OFF) Rotate the dimmer control to the OFF position (extreme bottom). The interior lights will remain off when the doors or liftgate are open. Parade Mode (Daytime Brightness Feature) Rotate the dimmer control to the first detent.
Page 141: Daytime Running Lights (Canada/Fleet Vehicles Only)
Daytime Running Lights (Canada/Fleet Vehicles Only) The Daytime Running Lights will come on whenever the vehicle is running, the headlights are off, and the parking brake is off. The headlight switch must be used for normal night time driving. Lights-on Reminder If the headlights or the park lights are left on, or if the dimmer control is in the extreme top position after the ignition switch is turned off, a chime will sound when the...
Page 142: Front Fog Lights - If Equipped
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE remain on. refer to Electronic Vehicle Information Center (EVIC) “Customer Programmable Features” for more information. If the headlights are turned off before the ignition, they will turn off in the normal manner. NOTE: The headlights must be turned off within 45 seconds of turning the ignition off to activate this feature.
Page 143: Headlight Low/High Beam Selector Switch
Turn Signal Switch Turn Signal Warning If the vehicle electronics sense that the vehicle has traveled at over 18 mph (29 km/h) for about one mile with the turn signals on, a chime will sound to alert the driver. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 Headlight Low/High Beam Selector Switch Pull the multifunction lever toward the steering wheel to switch the headlights between HIGH and LOW beam.
Page 144 144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Always remove any build-up of snow that prevents the windshield wiper blades from returning to the OFF position. If the windshield wiper switch is turned OFF and the blades cannot return to the OFF position, damage to the wiper motor may occur.
Page 145 WARNING! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with defroster before and during wind- shield washer use.
Page 146: Tilt Steering Column - If Equipped
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT STEERING COLUMN — IF EQUIPPED To tilt the column, pull the small lever, located behind the turn signal control, toward you and move the wheel up or down, as desired. Release the lever to lock the wheel firmly in place.
Page 147: Traction Control Switch - If Equipped
TRACTION CONTROL SWITCH — IF EQUIPPED The TRAC indicator, located below the instrument clus- ter odometer, will light up when the Traction Control is in use. To turn the system OFF, press the TRAC OFF switch located on the steering column, until the TRAC OFF indicator below the instrument cluster odometer lights UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 Traction Control Switch...
Page 148: Rear Park Assist System - If Equipped
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • The Traction Control System indicator comes on each time the ignition switch is turned ON. This will occur even if you used the switch to turn the system OFF. • The Traction Control will make buzzing or clicking sounds when in operation.
Page 149 WARNING! Drivers must be careful when backing up even when using the Rear Park Assist System. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, other vehicles, obstructions, and blind spots before backing up. Failure to do so can result in serious personal injury or death.
Page 150: Adjustable Pedals - If Equipped
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ADJUSTABLE PEDALS — IF EQUIPPED This feature allows both the brake and accelerator pedals to move toward or away from the driver to provide improved position with the steering wheel. The adjust- able pedal system is designed to allow a greater range of driver comfort for steering wheel tilt and seat position.
Page 151: Electronic Speed Control - If Equipped
• The pedals can be adjusted while driving. • The pedals cannot be adjusted when the vehicle is in R (Reverse) or when the Speed Control System is ON. The following messages will be displayed on vehicles equipped with the Electronic Vehicle Information Sys- tem (EVIC) if the pedals are attempted to be adjusted when the system is locked out (“Adjustable Pedal Disabled —...
Page 152: To Activate
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Activate: Push the “ON/OFF” button once and the CRUISE indi- cator located below the instrument cluster odometer will illuminate showing the electronic speed control system is on. To turn the system OFF, push the “ON/OFF” button again and the system and indicator will turn off.
Page 153: To Vary The Speed Setting
To Vary the Speed Setting: When the speed control is set, speed can be increased by pressing and holding the “RESUME/ACCEL” button. When the button is released, a new set speed will be established. Tapping the “RESUME/ACCEL” button once will result in a 2 mph (3 km/h) speed increase.
Page 154: Overhead Console - If Equipped
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Speed Control can be dangerous where the system can’t maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. An accident could be the result. Don’t use Speed Control in heavy traffic or on roads that are winding, icy, snow-covered, or slippery.
Page 155: Sunglass Storage
The lights also turn on when a front door, a sliding door or the liftgate is opened. If your vehicle is equipped with Remote Keyless Entry, the lights will also turn on when the unlock button on the transmitter is pressed. The area around the instrument panel cupholders is also illuminated from a light in the overhead console.
Page 156 156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE turns in an area free from large metal or metallic objects, the “CAL” symbol will turn off and the compass will function normally. Manual Compass Calibration If the compass appears erratic and the “CAL” symbol does not appear, you must put the compass into the Calibration Mode manually.
Page 157 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 To set the variance: Turn the ignition switch ON and set the display to Comp/Temp. On vehicles equipped with a Compass/Mini Trip Computer press the RESET button for approximately 5 seconds. On vehicles equipped with Compass/Temp press and hold the C/T and US/M buttons for 5 seconds.
Page 158: Mini-Trip Computer
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Mini-Trip Computer This displays information on the following: • Average Fuel Economy (ECO AVG) Shows the average fuel economy since the last reset. • Distance To Empty (DTE) Shows the estimated distance that can be travelled with the fuel remaining in the tank.
Page 159: Electronic Vehicle Information Center (Evic) - If Equipped
Electronic Vehicle Information Center (EVIC) — If Equipped The Electronic Vehicle Information Center, when the appropriate conditions exist, displays the following WARNING messages and symbols. Each message is accompanied by a single chime: • TURN SIGNALS ON (with graphic) • PERFORM SERVICE •...
Page 160: Customer Programmable Features - If Equipped
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Customer Programmable Features — If Equipped Press the “MENU” button until one of the display choices following appears: Language When in this display you may select one of five lan- guages for all display nomenclature, including the trip computer functions.
Page 161 Use Factory Settings If “Yes” is selected, all of the customer programmable features will be set to the factory default and not dis- played. If “No” is selected you can program the Vehicle Information Center to your own personal preferences. Auto Door Locks When this feature is selected, all doors and the liftgate lock automatically when the speed of the vehicle reaches...
Page 162 162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If this feature is not selected, the driver’s seat, driver’s mirror, adjustable pedals, and radio settings can only return to their memory set positions using the memory recall buttons (1or 2) on the driver’s door panel. Any transmitter linked to memory will remain linked, but will not recall the memory positions.
Page 163: Garage Door Opener - If Equipped
30, 60, or 90 seconds, or not remain on. Pressing the “STEP” button when in this display will select 30, 60, 90, or “OFF.” Headlamp On With Wipers (Available with Auto Headlights Only) When this feature is selected and the headlight switch has been moved to the “AUTO”...
Page 164: Programming Homelink
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse”...
Page 165 HomeLink Buttons UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 WARNING! Vehicle exhaust contains carbon monoxide, a danger- ous gas. Do not run the vehicle’s exhaust while training the transceiver. Exhaust gas can cause seri- ous injury or death. WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver.
Page 166 166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Position the end of your hand-held transmitter 1-3 inches (3-8 cm) away from the HomeLink buttons while keeping the indicator light in view. 3. Simultaneously press and hold both the HomeLink button that you want to train and the hand-held trans- mitter buttons.
Page 167: Canadian Programming/Gate Programming
7. Firmly press and release the learn or smart button. (The name and color of the button may vary by manu- facturer.) NOTE: There are 30 seconds in which to initiate step eight. 8. Return to the vehicle and firmly press, hold for two seconds and release the programmed HomeLink button.
Page 168: Using Homelink
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE successfully been accepted by HomeLink. (The indicator light will flash slowly and then rapidly.) Proceed with Programming step four to complete. Using HomeLink To operate, simply press and release the programmed HomeLink button. Activation will now occur for the trained device (i.e.
Page 169: Security
Security If you sell your vehicle, be sure to erase the frequencies by following the “Erasing HomeLink Buttons” instruc- tions in this section. This device complies with part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: •...
Page 170: Express Open Feature
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE switch rearward will activate the Express Open Feature, causing the sunroof to open automatically. Press and hold the button located to the right of the sunroof switch, to open the vent. The sunroof can be stopped at any position between closed and full vent.
Page 171: Wind Buffeting
WARNING! In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passengers are properly secured too. Do not allow small children to operate the sunroof.
Page 172: Electrical Power Outlets - If Equipped
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRICAL POWER OUTLETS — IF EQUIPPED To the left of the instrument panel cup holder are two 12 volt power outlets. The upper outlet is controlled by the ignition switch and the lower outlet is connected directly to the battery.
Page 173: Electrical Outlet Use With Engine Off
The lower outlet is protected by an automatic reset circuit breaker. The automatic circuit breaker restores power when the overload is removed. The circuit breaker also supplies power to the outlet in the removable floor console, when in the front position. Refer to section 3 “Removable Floor Console”...
Page 174: Convenience Tray Drawer And Cup Holders
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONVENIENCE TRAY DRAWER AND CUP HOLDERS Instrument Panel Cup Holders The instrument panel cupholders are located in a pull out drawer just below the climate controls. Front Cupholders When the drawer is pulled out firmly, the arms of the cupholders will spring out.
Page 175: Convenience Tray And Optional Smoker's Package Kit
Convenience Tray And Optional Smoker’s Package Kit Located between the instrument panel cupholders is a convenience tray that has been designed to hold miscel- laneous small items. NOTE: The convenience tray should never be used for ashes without the optional ash receiver in place. Perma- nent burn marks may result.
Page 176 176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If your vehicle is equipped with quad seats in the 2nd seat position, these cupholders are located on the out- board side of the seat pedestal. Quad Seat Cupholder NOTE: • The quad seat cupholders will remain upright if the seat is tilted forward.
Page 177: Storage
STORAGE Front Seat Storage Bin — If Equipped The storage bin is located under the front passenger’s seat. If equipped with a lock, it can be locked with the ignition key. Front Seat Storage Bin UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 Second Row Seat Storage bins —...
Page 178: Overhead Rail System - If Equipped
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! In an accident, serious injury could result if the seat storage bin covers are not properly latched. Do not drive the vehicle with the storage bin cover open. Keep the storage bin cover closed and latched while the vehicle is in motion.
Page 179: Removable Floor Console With Fold-In-Floor Seating - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 Removable Floor Console With Fold-in-Floor Seating — If Equipped The removable floor console has a two power outlets, storage tray, light, removable cell phone holder, tissue holder, pen holder and a map holder. It can be removed from the vehicle by pulling the release handle inside the floor console.
Page 180: Removable Floor Console Without Fold-In-Floor Seating - If Equipped
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To reinstall the console, open the console lid and remove the storage tray. Pull up on the release handle and slide the console forward to engage the front of the console into the floor tray. Pivot the floor console down until it is seated on the floor tray and release the handle.
Page 181 Removable Floor Console To remove the console use the following procedure: 1. Open the rear lid and remove the storage tray. 2. Pull up on the release handle located inside the floor console to disengage the floor console, reinstall the storage tray and close the rear lid.
Page 182 182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To reinstall the console, remove the rubber mat and relocate to the alternate floor tray, slide the console forward to engage the front of the console into the floor tray. Rapidly push down on the rear of the console with enough force to engage the latch, you should hear the latch “snap”...
Page 183 2. Plug in the power cord for the cellular phone into the outlet located in the bottom of the forward console bin and reinstall the cell phone holder. 3. Place the cell phone into the holder. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 CAUTION! •...
Page 184: Rear Compartment Storage Bins
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Compartment Storage Bins Your vehicle may be equipped with open storage bins located in each rear trim panel or your vehicle may be equipped with storage bins located under the armrest in each rear trim panel.
Page 185: Roof Luggage Rack - If Equipped
Loading Limit ROOF LUGGAGE RACK — IF EQUIPPED The crossbars and siderails are designed to carry the weight on vehicles equipped with a luggage rack. The load must not exceed 68 kg (150 lbs), and should be uniformly distributed over the luggage rack crossbars. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 Roof Rack Distribute cargo weight evenly on the roof rack crossbars.
Page 186 186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To move the cross bars, loosen the thumb screws located at the upper edge of each cross bar approximately six turns, then move the cross bar to the desired position. Once the cross bar is in place, retighten the thumb screws to lock the cross bar into position.
Page 187: Load Leveling System
WARNING! Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage. Follow the Roof Rack Cautions when carrying cargo on your roof rack.
Page 189: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instruments And Controls ....195 Base Instrument Cluster ....196 Instrument Cluster With Tach .
Page 190 190 UNDERSTANDING YOUR INSTRUMENT PANEL Tuning ......210 Radio Data System (RDS) ....210 PTY (Program Type) Button .
Page 191 Mode ......217 Tape CD Button ..... . 217 Time Button .
Page 192 192 UNDERSTANDING YOUR INSTRUMENT PANEL 6 Disc CD Changer — If Equipped ..244 Loading The CD Changer ....244 Playing Discs .
Page 193 Satellite Radio — If Equipped ....258 System Activation ..... 258 Electronic Serial Number/Sirius Identification Number (ENS/SID) .
Page 194 194 UNDERSTANDING YOUR INSTRUMENT PANEL Manual Air Conditioning Operation ..271 Manual Rear Zone Climate Control — If Equipped ......274 Infrared Three-Zone Automatic Temperature Control —...
Page 195: Instruments And Controls
UNDERSTANDING YOUR INSTRUMENT PANEL 195 INSTRUMENTS AND CONTROLS...
Page 196: Base Instrument Cluster
196 UNDERSTANDING YOUR INSTRUMENT PANEL BASE INSTRUMENT CLUSTER...
Page 197: Instrument Cluster With Tach
UNDERSTANDING YOUR INSTRUMENT PANEL 197 INSTRUMENT CLUSTER WITH TACH...
Page 198: Premium Instrument Cluster
198 UNDERSTANDING YOUR INSTRUMENT PANEL PREMIUM INSTRUMENT CLUSTER...
Page 199: Instrument Cluster Descriptions
INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON position. 2. Tire Pressure Monitor Warning Light — If Equipped This light will turn on when there is a Low tire pressure condition.
Page 200 200 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Low Fuel Light When the fuel level reaches approximately 3.0 gallons (11.0 liters) this light will turn on and remain on until fuel is added. 4. Turn Signal Indicators The arrow will flash with the exterior turn signal when the turn signal lever is operated.
Page 201 The light will remain on until the cause is corrected. NOTE: The light may flash momentarily during sharp cornering maneuvers which change fluid level condi- tions. The vehicle should have service performed. If brake failure is indicated, immediate repair is neces- sary.
Page 202 202 UNDERSTANDING YOUR INSTRUMENT PANEL 9. Airbag Light This light turns on and remains on for 6 to 8 seconds as a bulb check when the ignition switch is first turned ON. If the light is not on during starting, stays on, or turns on while driving, have the system inspected by an authorized dealer as soon as possible.
Page 203 13. Seat Belt Reminder Light When the ignition switch is first turned ON, this light will turn on for 5 to 8 seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound. After the bulb check or when driving, if the driver seat belt remains unbuckled, the Seat Belt Warning Light will flash or remain on continuously.
Page 204 204 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Driving with a hot engine cooling system could damage your vehicle. If temperature gauge reads (H), pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.
Page 205 NOTE: You must apply the brakes before shifting from Park. 19. Oil Pressure Warning Light This light shows low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible.
Page 206 206 UNDERSTANDING YOUR INSTRUMENT PANEL 22. Trac Off Indicator — If Equipped This display indicator should illuminate for approxi- mately four seconds as a bulb check when the ignition switch is first turned ON. The “TRAC OFF” Indicator will flash if the traction control is in use.
Page 207: Electronic Digital Clock
The trip odometer shows individual trip mileage. To switch from odometer to trip odometer, press the Trip Odometer button. 24. Cruise Indicator This display indicator shows that the Speed Control System is ON. 25. Trip Odometer Button Press this button to change the display from odometer to trip odometer.
Page 208: Radio General Information
208 UNDERSTANDING YOUR INSTRUMENT PANEL RADIO GENERAL INFORMATION Radio Broadcast Signals Your new radio will provide excellent reception under most operating conditions. Like any system, however, car radios have performance limitations, due to mobile op- eration and natural phenomena, which might lead you to believe your sound system is malfunctioning.
Page 209: Sales Code Raz-Am/ Fm Stereo Radio With Cassette Tape Player, Cd Player And Cd Changer Controls
remain active for up to 45 seconds after the ignition switch has been turned off. Opening a vehicle front door will cancel this feature. SALES CODE RAZ—AM/ FM STEREO RADIO WITH CASSETTE TAPE PLAYER, CD PLAYER AND CD CHANGER CONTROLS RAZ Radio UNDERSTANDING YOUR INSTRUMENT PANEL 209 Operating Instructions —...
Page 210: Tuning
210 UNDERSTANDING YOUR INSTRUMENT PANEL Tuning Press the TUNE control up or down to increase or decrease the frequency. If you press and hold the button, the radio will continue to tune until you release the button. The frequency will be displayed and continu- ously updated while the button is pressed.
Page 211 Toggle the PTY button to select the following format types: Program Type Radio Display Adult Hits Adlt Hit Classical Classicl Classic Rock Cls Rock College College Country Country Information Inform Jazz Jazz Foreign Language Language News News Nostalgia Nostalga Oldies Oldies Personality Persnlty...
Page 212: Balance
212 UNDERSTANDING YOUR INSTRUMENT PANEL no station is found with the selected PTY program type, the radio will return to the last preset station. If a preset button is activated while in the PTY (Program Type) mode, the PTY mode will be exited and the radio will tune to the preset station.
Page 213: Scan Button
Scan Button Pressing the SCAN button causes the tuner to search for the next station, in either AM or FM, pausing for 5 seconds at each listenable station before continuing to the next. Pressing the AM/FM button continues the search in the alternate frequency band.
Page 214: Seek Button
214 UNDERSTANDING YOUR INSTRUMENT PANEL be experienced due to a defective cassette tape. Clean and demagnetize the tape heads at least twice a year. Seek Button Press the SEEK button up for the next selection on the tape and down to return to the beginning of the current selection.
Page 215: Metal Tape Selection
Metal Tape Selection If a standard metal tape is inserted into the player, the player will automatically select the correct equalization and the 70 symbol will appear in the display window. Pinch Roller Release If ignition power or the radio ON/OFF switch are turned off, the pinch roller will automatically retract to protect the tape from any damage.
Page 216: Inserting The Compact Disc
216 UNDERSTANDING YOUR INSTRUMENT PANEL Inserting The Compact Disc The CD player contained within the radio is not a multi-disc changer, and will only accept one CD. Gently insert one CD into the CD player with the CD label facing up.
Page 217: Ff/Tune/Rw
FF/TUNE/RW Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW ( Reverse) button works in a similar manner. Program Button 4 (Random Play) Press this button while the CD is playing to activate Random Play.
Page 218: Time Button
218 UNDERSTANDING YOUR INSTRUMENT PANEL Time Button Press this button to change the display from elapsed CD playing time to time of day. Scan Button Press this button to play the first 10 seconds of each track. To stop the scan function, press the button a second time. CD Changer Control Capability —...
Page 219: Sales Code Rbp-Am & Fm Stereo Radio With Cassette Tape Player, Cd Player, And Optional Cd/Dvd Changer Controls
CD Diagnostic Indicators When driving over a very rough road, the CD player may skip momentarily. Skipping will not damage the disc or the player, and play will resume automatically. As a safeguard and to protect your CD player, one of the following warning symbols may appear on your display.
Page 220: Radio Operation
220 UNDERSTANDING YOUR INSTRUMENT PANEL Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control to the right to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio.
Page 221 Program Type Radio Display Rock Rock Soft Soft Soft Rock Soft Rck Soft Rhythm and Blues Soft R&B Sports Sports Talk Talk Top 40 Top 40 Weather Weather By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name.
Page 222 222 UNDERSTANDING YOUR INSTRUMENT PANEL Scan Press and release the SCAN button to search for the next station in either the AM or FM mode. The radio will pause for 5 seconds at each listenable station before continuing to the next. To stop the search, press the SCAN button a second time.
Page 223 SET 1 will now show in the display window. Select the “1–5” button you wish to lock onto this station and press and release that button. If a button is not selected within 5 seconds after pressing the SET button, the station will continue to play but will not be locked into push-button memory.
Page 224: Tape Player Operation
224 UNDERSTANDING YOUR INSTRUMENT PANEL Tape Player Operation Insert the cassette with the exposed tape side toward the right and the mechanical action of the player will gently pull the cassette into the play position. NOTE: When subjected to extremely cold temperatures, the tape mechanism may require a few minutes to warm up for proper operation.
Page 225 Rewind — RW Press the RW button down momentarily to reverse the tape direction. The tape will rewind until the button is pressed again or until the beginning of the tape is reached. At the beginning of the tape, the tape will play in the opposite direction.
Page 226: Cd Player Operation
226 UNDERSTANDING YOUR INSTRUMENT PANEL CD Player Operation NOTE: The ignition switch must be in the ON or ACC position and the volume control ON before the CD player will operate. Inserting The Compact Disc You may either insert or eject a disc with the radio OFF. If you insert a disc with the ignition ON and the radio off, the display will show CD and the time of day will be displayed.
Page 227: Cd/Dvd Changer Operation
FF/TUNE/RW Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW (Reverse) button works in a similar manner. Random Play — RND/Program Button 4 Press the RND (button 4) button while the CD is playing to activate Random Play.
Page 228 228 UNDERSTANDING YOUR INSTRUMENT PANEL Disc Up/Program Button 1 Press the DISC (button 1) button to play the next avail- able disc. Random Play — RND/Program Button 4 Press the RND (button 4) button while the CD is playing to activate Random Play. This feature plays the selections on the currently playing compact disc in random order to provide an interesting change of pace.
Page 229: Sales Code Rbq-Am/Fm Stereo Radio With 6 - Disc Cd Changer
SALES CODE RBQ—AM/FM STEREO RADIO WITH 6 - DISC CD CHANGER RBQ Radio UNDERSTANDING YOUR INSTRUMENT PANEL 229 Radio Operation Power/Volume Control Press the PWR/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is controlled by the ignition switch.
Page 230 230 UNDERSTANDING YOUR INSTRUMENT PANEL channel number will then be displayed for five seconds. The current channel name and number will then be displayed until an action occurs. CD’s may remain in the player while in the Satellite Radio mode. Seek Press and release the SEEK button to search for the next station in either the AM or FM mode.
Page 231 Audio The audio button controls the BASS, TREBLE, BAL- ANCE, and FADE. Press the AUDIO button and BASS will be displayed. Press the SEEK + or SEEK – to increase or decrease the Bass tones. Press the AUDIO button a second time and TREB will be displayed.
Page 232: Cd Player Operation
232 UNDERSTANDING YOUR INSTRUMENT PANEL CD Player Operation NOTE: The ignition switch must be in the ON or ACC position and the Power / Volume control pushed ON before the CD player will operate. Inserting The Compact Disc CAUTION! This CD player will accept 4 only.
Page 233 Radio display will show “ejecting” when it is being ejected. If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded. If the CD is not removed, the radio will continue to play the non-removed CD. If the CD is removed and there are other CD’s in the radio, the radio will play the next CD.
Page 234 234 UNDERSTANDING YOUR INSTRUMENT PANEL PTY (Program Type) Button Pressing this button once will turn on the PTY mode for 5 seconds. If no action is taken during the 5 second time out the PTY icon will turn off. Pressing the PTY button repeatedly within 5 seconds will allow the program format type to be selected.
Page 235 Program Type Radio Display Talk Talk Top 40 Top 40 Weather Weather By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode.
Page 236: Sales Code Rbk-Am/ Fm Stereo Radio With Cd Player And Cd Changer Controls
236 UNDERSTANDING YOUR INSTRUMENT PANEL A CD HOT symbol indicates the player is too hot. CD HOT will pause the operation. Play can be resumed when the operating temperature is corrected or another MODE is selected. CD ERROR will appear on the display if the laser is unable to read the Disc data for the following reasons: •...
Page 237: Radio Operation
Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio.
Page 238 238 UNDERSTANDING YOUR INSTRUMENT PANEL stations stored in SET 2 memory can be selected by pressing the push-button twice. Every time a preset button is used a corresponding button number will be displayed. Audio The audio button controls the BASS, TREBLE, BAL- ANCE, and FADE.
Page 239: Cd Player Operation
1. This device may not cause harmful interference, 2. This device must accept any interference received, including interference that may cause undesired opera- tion. NOTE: Changes or modifications not expressively ap- proved by the party responsible for compliance could void the user’s authority to operate the equipment. CD Player Operation NOTE: The ignition switch must be in the ON or ACC position and the volume control ON before the CD player...
Page 240 240 UNDERSTANDING YOUR INSTRUMENT PANEL Seek Press the top of the SEEK button for the next selection on the CD. Press the bottom of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first second of the current selection.
Page 241: Cd Changer Control Capability - If Equipped
Satellite Radio (if equipped). When Satellite Radio (if equipped) is selected “SAT” will appear in your radio display. A CD or tape may remain in the player while in the Satellite mode. Time Press the TIME button to change the display from elapsed CD playing time to time of day.
Page 242 242 UNDERSTANDING YOUR INSTRUMENT PANEL Random Play (RND) Press the Random button to play the tracks on the selected disc in random order for an interesting change of pace. Random can be cancelled by pressing the button a second time or by ejecting the CD from the changer. Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s...
Page 243: Sales Code Rb1-Am/Fm Stereo Radio With Dvd/Gps Navigation System
SALES CODE RB1—AM/FM STEREO RADIO WITH DVD/GPS NAVIGATION SYSTEM RB1 Radio UNDERSTANDING YOUR INSTRUMENT PANEL 243 The navigation system provides maps, turn identifica- tion, selection menus and instructions for selecting a variety of destinations and routes. Refer to your “Navi- gation User’s Manual”...
Page 244: Disc Cd Changer - If Equipped
244 UNDERSTANDING YOUR INSTRUMENT PANEL 6 DISC CD CHANGER — IF EQUIPPED The CD changer is located below the radio in the instrument panel. The changer plays only 4 cm) discs. The changer holds up to 6 discs. Each disc is loaded and ejected through a single slot in front of the changer.
Page 245: Playing Discs
Playing Discs The radio will show the CD number, the CD track number, and the Track Time Elapsed while the radio is in the CD mode. If more than one CD is loaded in the changer, the changer will automatically play the next disc after playing the last track of the current disc.
Page 246: Program Button 5
246 UNDERSTANDING YOUR INSTRUMENT PANEL Program Button 5 Press this button to play the previous disc. Time Button Press this button to switch between time of day and CD track time. Changing Modes While in the radio mode, if a cassette is loaded, press the Mode button to switch to the tape mode.
Page 247: Operating Instructions - Cd/Dvd Changer
as selecting discs loaded in the 6 disc CD/DVD changer while listening to the Rear Audio/Video System. The Rear Seat Audio/Video System may be available in a base and premium version. The premium version in- cludes a six disc changer, remote control and two sets of wireless headphones.
Page 248 248 UNDERSTANDING YOUR INSTRUMENT PANEL To insert disc(s) into the changer, follow the instructions shown: 1. On vehicles equipped with the premium version, select and press any numbered button without an illumi- nated light above it. 2. Gently insert the disc with the label facing up while the light below the loading slot is illuminated.
Page 249: Eject (Ejt) Button
• If you insert a disc with the ignition ON and the radio OFF, the DVD will automatically be pulled into the DVD changer and the display will show the time of day. • It is recommended to label home made burned discs with a permanent marker instead of adhesive labels.
Page 250: Operating Instructions - Remote Control
250 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Remote Control NOTE: Aim the remote control at the DVD changer located on the center of the instrument panel and press the desired button. Direct sunlight or objects blocking the line of sight may affect the function of the remote control. Remote Control...
Page 251 Remote Control Buttons 1. Headphone Transmitter 2. Menu Up/Next Track/Chapter 3. Menu Left/Fast Rewind 4. Return 5. Setup 6. Pause/Play 7. Mute 8. Display 9. Mode 10. Program Down - Previous Disc 11. Program Up - Next Disc 12. Slow 13.
Page 252 252 UNDERSTANDING YOUR INSTRUMENT PANEL RTN Button (4) This button only functions in DVD video mode. Press this button to return to the previous menu when in the DVD disc menu mode. SETUP Button (5) This button only functions in DVD video mode. Press the button after pressing the STOP button to access the DVD changer set up menu.
Page 253 SLOW Button (12) This button only functions in DVD video mode. Press this button to advance the video. If the DVD is paused, pressing this button will advance the video frame by frame. STOP Button (13) This button only functions in DVD video mode. Press this button to stop the DVD.
Page 254: Operating Instructions - Video Screen
254 UNDERSTANDING YOUR INSTRUMENT PANEL Remote Control Battery Service • To replace the batteries for the remote control slide the cover rearward. The replacement batteries for the remote control are two AAA batteries. Operating Instructions — Video Screen Push up on the release button to lower the video screen. Lowering Video Screen...
Page 255 1. Screen Width Button Changes the width of the screen picture. 2. Enter Button This button will enter the selection from the on-screen menu. 3. Brightness Button Changes the brightness of the screen picture. UNDERSTANDING YOUR INSTRUMENT PANEL 255 Video Screen Controls...
Page 256: Operating Instructions - Headphones
256 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Headphones Headphone Controls 1. Power Button 2. Volume Control 3. Power Indicator Power Button Pressing the power button will turn the headphones ON/OFF. An indicator light will illuminate on the head- phone earpiece to indicate the headphones are ON. NOTE: •...
Page 257 Headphone Battery Service • Replace the battery in each earpiece and reinstall the cover. The headphones require two AAA batteries. General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause UNDERSTANDING YOUR INSTRUMENT PANEL 257 harmful interference and (2) This device must accept any...
Page 258: Operating Instructions - Mp3 Player, Portable Walkman
258 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — MP3 Player, Portable Walkman An MP3 player can be connected to the audio system. Connect the cables to the RCA jacks located on the front of the CD/DVD changer. NOTE: Follow the manufactures instructions for the correct colors when connecting the RCA cables.
Page 259: Electronic Serial Number/Sirius Identification Number (Ens/Sid)
2. Credit card information. 3. Your Vehicle Identification Number. Electronic Serial Number/Sirius Identification Number (ENS/SID) The Electronic Serial Number/Sirius Identification Num- ber is needed to activate your Sirius Satellite Radio system. To access the ESN/SID, refer to the following steps: ESN/SID Access With RBB, RAH and RBK Radios With the ignition switch in the ACCESSORY position and the radio OFF, press the Tape Eject or CD Eject (depend-...
Page 260: Selecting Satellite Mode In Rbp, Rbu, Raz, Rb1 And Rbq Radios
260 UNDERSTANDING YOUR INSTRUMENT PANEL Selecting Satellite Mode in RBP, RBU, RAZ, RB1 and RBQ Radios Press the MODE button repeatedly until the word SIRIUS appears in the display. These radios will also display the following: • After 3 seconds, the current channel name and channel number will be displayed for 5 seconds.
Page 261: Storing And Selecting Pre-Set Channels
Storing and Selecting Pre-Set Channels In addition to the 10 AM and 10 FM pre-set stations, you may also commit 10 satellite stations to push button memory. These satellite channel pre-set stations will not erase any AM or FM pre-set memory stations. Follow the memory pre-set procedures that apply to your radio.
Page 262: Reception Quality
262 UNDERSTANDING YOUR INSTRUMENT PANEL Reception Quality Satellite reception may be interrupted due to one of the following reasons. • The vehicle is parked in an underground parking structure or under a physical obstacle. • Dense tree coverage may interrupt reception in the form of short audio mutes.
Page 263: Radio Operation
The right hand rocker switch has a push button in the center and controls the volume and mode of the sound system. Pressing the top of the rocker switch will increase the volume and pressing the bottom of the rocker switch will decrease the volume.
Page 264: Cd Player
264 UNDERSTANDING YOUR INSTRUMENT PANEL CD Player Pressing the top of the switch once will go to the next track on the CD. Pressing the bottom of the switch once will go to the beginning of the current track or to the beginning of the previous track if it is within one second after the current track begins to play.
Page 265: Cd/Dvd Disc Maintenance
turned all the way down. To prevent this, you should periodically clean the head with a commercially available WET cleaning cassette. As preventive maintenance, clean the head about every 30 hours of use. If you wait until the head becomes very dirty (noticeably poor sound), it may not be possible to remove all deposits with a simple WET cleaning cassette.
Page 266: Climate Controls
266 UNDERSTANDING YOUR INSTRUMENT PANEL CLIMATE CONTROLS The Air Conditioning and Heating System is designed to make you comfortable in all types of weather. Manual Air Conditioning and Heating System Manual Air Conditioning and Heating Controls Front Blower Control The Front Blower Control selects whether the Cli- mate Control System is ON or OFF.
Page 267: Front Mode Control
Dual Zone Temperature Control — If Equipped With the Dual Zone Temperature Control System, each front seat occupant can independently control the tem- perature of air coming from the outlets on their side of the vehicle. Dual Zone Temperature Control This is accomplished by having a separate temperature control lever for both the driver and front seat passenger.
Page 268 268 UNDERSTANDING YOUR INSTRUMENT PANEL Panel Mode Panel Outlets Air comes from the outlets in the instrument panel. Each of these outlets can be individually adjusted to direct the flow of air. Moving the air vane knob on the center outlets down, will close off the air flow from the center outlets.
Page 269 Bi-Level Mode Bi-Level Outlets Air comes from both the instrument panel outlets, floor outlets and defrost. A slight amount of air is also directed through the side window demister outlets. UNDERSTANDING YOUR INSTRUMENT PANEL 269 NOTE: In many temperature lever positions, the bi- level mode is designed to provide cooler air out of the panel outlets and warmer air from the floor outlets.
Page 270 270 UNDERSTANDING YOUR INSTRUMENT PANEL Floor Mode Floor Outlets Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. Mix Mode Mix Outlets Air comes from the floor, defrost and side window demist outlets.
Page 271: Manual Air Conditioning Operation
Defrost Mode Defrost Outlets Air comes from the windshield and side window demist outlets. Use this setting when necessary to defrost your windshield and side windows. NOTE: For improved safety, the compressor is activated and the recirculation mode is deactivated when Mix or UNDERSTANDING YOUR INSTRUMENT PANEL 271 Defrost modes are selected.
Page 272 272 UNDERSTANDING YOUR INSTRUMENT PANEL • If your air conditioning performance seems lower than expected, check the A/C air filter and the front of the A/C condenser for an accumulation of dirt or insects. The A/C condenser is located in front of the radiator. The A/C air filter is located under the instrument panel on the passenger side.
Page 273 A/C Recirculation Programming The recirculation control is programmed to cancel the recirculation mode when the ignition key is turned OFF and will reset to outside air mode when the ignition key is turned ON. The frequent use of outside air will help keep odors from building up within the air conditioner- heater housing.
Page 274: Manual Rear Zone Climate Control - If Equipped
274 UNDERSTANDING YOUR INSTRUMENT PANEL Manual Rear Zone Climate Control — If Equipped The Manual Rear Zone Climate Control system has floor air outlets to the rear of the right side sliding door and overhead outlets at each outboard rear seating position. The unit provides warm or cool air through the floor and upper outlets.
Page 275 Only when the primary control for the rear blower is in the “REAR” position do the second seat occupants have control of the rear blower speed. The rear blower control, located in the headliner near the center of the vehicle has an OFF position and 3 blower speed positions.
Page 276: Infrared Three-Zone Automatic Temperature Control - If Equipped
276 UNDERSTANDING YOUR INSTRUMENT PANEL in the cold position, cold air will be delivered from the headliner outlets. As the rear temperature knob is turned towards hot, the air will get warmer, and the air will be delivered from both the headliner and floor outlets.
Page 277 Three-Zone Automatic Temperature Control Operation of the system is quite simple. Begin by press- ing the auto rocker switch to the “HI” or “LO” position, the word “AUTO” will illuminate in the front ATC display along with “HI” or “LO”. The system will then automatically regulate the amount of air flow.
Page 278 278 UNDERSTANDING YOUR INSTRUMENT PANEL off and “DELAY” will appear in the front ATC display until the engine warms up. Also, an estimate of the time remaining until the “DELAY” is over will appear peri- odically in the display. However, the fan will engage immediately if the defrost mode is selected or by rotating the blower control to any fixed blower speed.
Page 279 speeds are selected or either the Auto HI or Auto LO buttons are pressed. This allows the front occupants to control the volume of air circulated in the vehicle and cancel the “AUTO” mode. The operator can also select the direction of the air by rotating the right mode control knob to one of the following positions.
Page 280 280 UNDERSTANDING YOUR INSTRUMENT PANEL Bi-Level Mode Bi-Level Outlets Air comes from both the instrument panel outlets, floor outlets and defrost. A slight amount of air is also directed through the side window demister outlets. NOTE: In many temperature positions, the bi-level mode is designed to provide cooler air out of the panel outlets and warmer air from the floor outlets.
Page 281 Floor Mode Floor Outlets Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. UNDERSTANDING YOUR INSTRUMENT PANEL 281 Mix Mode Mix Outlets Air comes from the floor, defrost and side window demist outlets.
Page 282 282 UNDERSTANDING YOUR INSTRUMENT PANEL Defrost Mode Defrost Outlets Air comes from the windshield and side window demist outlets. Use this setting when necessary to defrost your windshield and side windows. NOTE: While operating in either Auto HI or Auto LO , the system will not automatically sense the presence of fog, mist, or ice on the windshield.
Page 283 the recirculation button. The recirculation mode should only be used temporarily. The recirculation symbol will illuminate in the display when this button is selected. Push the button a second time to turn off the recirculation icon in the display and allow outside air into the vehicle. NOTE: In cold weather, use of the Recirculation mode may lead to excessive window fogging.
Page 284 284 UNDERSTANDING YOUR INSTRUMENT PANEL The Rear Automatic Temperature Control System is located in the headliner near the center of the vehicle. Rear Automatic Temperature Control Operation of the rear system is quite simple. Begin by rotating the rear system center control knob on the front ATC control unit to the “REAR CONTROL”...
Page 285 Rear Blower Control The rear blower control, located in the headliner near the center of vehicle “AUTO” and a range of blower speeds. The rear blower control knob can be manually set to “OFF” or any fixed blower speed by rotating the knob from low to high.
Page 286 286 UNDERSTANDING YOUR INSTRUMENT PANEL Rear Mode Control The Rear Mode Control, located in the headliner near the center of the vehicle can be used to select between Auto, Headliner, Bi- Level and Floor modes. Auto Mode The rear system automatically maintains the correct mode and comfort level desired by the rear seat occu- pants.
Page 287 glycol antifreeze coolant in water is recommended. Refer to section 7, Maintenance Procedures, of this manual for proper coolant selection. Winter Operation To insure the best possible heater and defroster perfor- mance, make sure the engine cooling system is function- ing properly and the proper amount, type, and concen- tration of coolant is used.
Page 288: Rear Window Features
288 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips A/C Air Filter — If Equipped The climate control system filters out dust, pollen and some odors from the air. Strong odors can not be totally filtered out. Refer to MAINTAINING YOUR VEHICLE, “Air Conditioner Maintenance”...
Page 289: Rear Washer Operation - Manual Temperature Control Only
Rear Washer Operation — Manual Temperature Control Only The controls are located on the Manual Tempera- ture Control head above the front blower control. Press and hold the button for as long as spray is desired. If the button is depressed and held while the Intermittent wiper is on, the wiper will operated for a few seconds after the button is released, then resume inter- mittent operation.
Page 290: Intermittent Rear Wiper Operation - Automatic Temperature Control Only
290 UNDERSTANDING YOUR INSTRUMENT PANEL Intermittent Rear Wiper Operation — Automatic Temperature Control Only When this button is pressed and the ignition switch is in the ON position, the rear wiper will operate at a fixed interval of about 8 seconds. As vehicle speed increases, the time delay will shorten.
Page 291: Electric Rear Window Defroster - If Equipped
Washer Fluid Reservoir The washer fluid reservoir will hold a full gallon of fluid when the Low Washer Fluid Light illuminates. UNDERSTANDING YOUR INSTRUMENT PANEL 291 Electric Rear Window Defroster — If Equipped Press this button to turn on the rear window defroster and the optional heated mirrors.
Page 292 292 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! To avoid damaging the electrical conductors of the rear window defroster, do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window. Labels can be peeled off after soaking with warm water.
Page 293: Starting And Operating
STARTING AND OPERATING CONTENTS Starting Procedures ..... 296 Normal Starting ..... . 296 Extremely Cold Weather (Below 29°...
Page 294 294 STARTING AND OPERATING Tire Markings ......310 Tire Identification Number (TIN) ..313 Tire Loading And Tire Pressure .
Page 295 Fuel System Cautions ....334 Carbon Monoxide Warnings ....335 Adding Fuel .
Page 296: Starting Procedures
296 STARTING AND OPERATING STARTING PROCEDURES CAUTION! Long periods of engine idling, especially at high engine speeds, can cause excessive exhaust tempera- tures which can damage your vehicle. Do not leave your vehicle unattended with the engine running. WARNING! Do not leave animals or children inside parked vehicles in hot weather;...
Page 297: If Engine Fails To Start
WARNING! Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic trans- mission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
Page 298: After Starting
298 STARTING AND OPERATING CAUTION! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again. If the engine has been flooded, it may start to run, but not have enough power to continue running when the key is released.
Page 299: Engine Block Heater - If Equipped
ENGINE BLOCK HEATER — IF EQUIPPED The engine block heater warms engine coolant and permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt AC electrical outlet with a grounded, three-wire extension cord. The engine block heater cord is routed under the hood on the driver side of the vehicle.
Page 300: Brake/Transmission Interlock System
300 STARTING AND OPERATING WARNING! It is dangerous to shift the selector lever out of “P” or “N” if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in re- verse.
Page 301 Reset Mode - Electronic Transmission The transmission is monitored electronically for abnor- mal conditions. If a condition is detected that could cause damage, the transmission automatically shifts into sec- ond gear. The transmission remains in second gear despite the forward gear selected. Park (P), Reverse (R), and Neutral (N) will continue to operate.
Page 302 302 STARTING AND OPERATING Apply parking brake when leaving vehicle in this range. • “R” Reverse Shift into this range only after the vehicle has come to a complete stop. • “N” Neutral Engine may be started in this range. •...
Page 303: Parking Brake
NOTE: The vehicle computer will over ride Overdrive and “3” Drive ranges by changing shift points if the transmission operating temperature exceeds acceptable limits. This is done to prevent transmission damage due to overheating. PARKING BRAKE When the parking brake is applied with the ignition switch on, the brake light in the instrument cluster will turn on.
Page 304: Brake System
304 STARTING AND OPERATING added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on a uphill grade. The parking brake should always be applied when the driver is not in the vehicle. WARNING! Leaving children in a vehicle unattended is danger- ous for a number of reasons.
Page 305: Anti-Lock Brake System - If Equipped
by increased pedal travel during application, greater pedal force required to slow or stop, and potential activation of the Brake Warning Lamp. Anti-Lock Brake System — If Equipped The Anti-Lock Brake System provides increased vehicle stability and brake performance under most braking conditions.
Page 306 306 STARTING AND OPERATING When the vehicle is driven over approximately 15 mph (25 km/h), you may also hear a slight clicking sound as well as some related motor noises. These noises are the system performing its self check cycle to ensure that the ABS system is working properly.
Page 307: Power Steering
WARNING! • Anti-lock system (ABS) cannot prevent the natu- ral laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency be- yond that afforded by the condition of the vehicle brakes and tires or the traction afforded. •...
Page 308: Traction Control - If Equipped
308 STARTING AND OPERATING WARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. CAUTION! Prolong operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and should be avoided when possible.
Page 309 Traction Control Switch • There is a Traction Control System malfunction • The system has been deactivated to prevent damage to the brake system due to overheated brake tempera- tures STARTING AND OPERATING 309 The Traction Control will make buzzing or NOTE: clicking sounds when in operation.
Page 310: Tire Safety Information
310 STARTING AND OPERATING TIRE SAFETY INFORMATION Tire Markings NOTE: • P(Passenger)-Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Ex- ample: P215/65R15 95H. • European Metric tire sizing is based on European design standards.
Page 311 Tire Sizing Chart Size Designation: P = Passenger car tire size based on U.S. design standards ...blank... = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Milimeters (mm) 65 = Aspect Ratio in Percent (%)
Page 312 312 STARTING AND OPERATING Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions.
Page 313: Tire Identification Number (Tin)
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. = Department of Transportation —This symbol certifies that the tire is in compliance with the U.S.
Page 314: Tire Loading And Tire Pressure
314 STARTING AND OPERATING Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure for pas- senger cars is listed on either the face of the driver’s door or the driver’s side “B” pillar. For vehicles other than passenger cars, the cold tire inflation pressures are listed on either the “B”...
Page 315 Tire and Loading Information Placard Tire and Loading Information This placard tells you important information about the, 1) number of people that can be carried in the vehicle 2) the total weight your vehicle can carry 3) the tire size designed for your vehicle STARTING AND OPERATING 315 4) the cold tire inflation pressures for the front, rear and spare tires.
Page 316 316 STARTING AND OPERATING combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here. Steps for Determining Correct Load Limit 1. Locate the statement “The combined weight of occu- pants and cargo should never exceed XXX pounds” on your vehicle’s placard.
Page 317 STARTING AND OPERATING 317...
Page 318: Tires-General Information
318 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
Page 319: Tire Inflation Pressures
2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption. 3.
Page 320 320 STARTING AND OPERATING check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are underinflated. CAUTION! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem.
Page 321 Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important.
Page 322: Radial-Ply Tires
322 STARTING AND OPERATING Radial-Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Al- ways use radial ply tires in sets of four (or 6, in case of trucks with dual rear wheels).
Page 323: Limited Use Spare - If Equipped
Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. Do not install more than one compact spare tire/wheel on the vehicle at any given time. CAUTION! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with the...
Page 324: Tire Spinning
324 STARTING AND OPERATING WARNING! The limited use spare tires are for emergency use only. Installation of this limited use spare tire affects vehicle handling. With this tire, do not drive more than 60 mph (100 km/h). Keep inflated to the cold tire inflation pressure listed on either your tire placard or limited use spare tire and wheel assembly.
Page 325: Replacement Tires
These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm). When the indicators appear in 2 or more adjacent grooves, the tire should be replaced. Many states have laws requiring tire replacement at this point.
Page 326: Alignment And Balance
326 STARTING AND OPERATING WARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspen- sion dimensions and performance characteristics, resulting in changes to steering, handling, and brak- ing of your vehicle.
Page 327: Tire Pressure Monitor System - If Equipped
Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-of- balance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. TIRE PRESSURE MONITOR SYSTEM — IF EQUIPPED The Tire Pressure Monitor System (TPM) system uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels (EXCLUDING THE SPARE TIRE).
Page 328: Check Tpm System
328 STARTING AND OPERATING CHECK TPM SYSTEM The Tire Pressure Monitor System (TPM) system requires service. See your authorized dealer for service. CAUTION! The TPM system has been optimized for the original equipment tires and wheels. TPM system pressures have been established for the tire size equipped on your vehicle.
Page 329: General Information
General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired op- eration.
Page 330: Tire Chains
330 STARTING AND OPERATING TIRE CHAINS Use only compact chains, or other traction aids that meet SAE type “Class S” specifications. Chains must be the proper size for the vehicle, as recommended by the chain manufacturer. NOTE: Do not use tire chains on a compact spare tire. CAUTION! To avoid damage to your vehicle or tires, observe the following precautions:...
Page 331: Snow Tires
NOTE: In order to avoid damage to tires, chains, and your vehicle do not drive for a prolonged period of time on dry pavement. Observe the tire chain manufacturer’s instructions on method of installation, operating speed, and conditions for usage. Always use the lower suggested operating speed if both the chain manufacturer and vehicle manufacture suggest a maximum speed.
Page 332: Fuel Requirements
332 STARTING AND OPERATING Section of this manual. More frequent rotation is permis- sible if desired. The reasons for any rapid or unusual wear should be corrected prior to rotation being per- formed. The suggested rotation method is the “forward-cross” shown in the following diagram.
Page 333: Reformulated Gasoline
Over 40 automobile manufacturers around the world have issued and endorsed consistent gasoline specifica- tions (the World Wide Fuel Charter, WWFC) to define fuel properties necessary to deliver enhanced emissions, engine performance, and durability for your vehicle. The manufacturer recommends the use of gasolines that meet the WWFC specifications if they are available.
Page 334: Mmt In Gasoline
334 STARTING AND OPERATING MMT In Gasoline MMT is a manganese containing metallic additive that is blended into some gasoline to increase the octane num- ber. Gasolines blended with MMT offer no performance advantage beyond gasolines of the same octane number without MMT.
Page 335: Carbon Monoxide Warnings
• An out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunctioning and may require immediate service. Contact your dealer for service assistance.
Page 336: Adding Fuel
336 STARTING AND OPERATING • Guard against carbon monoxide with proper mainte- nance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • Keep the liftgate closed when driving your vehicle to prevent carbon monoxide and other poisonous ex- haust gases from entering the vehicle.
Page 337 CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system. NOTE: The driver’s side sliding door cannot be opened while the fuel door is open.
Page 338: Vehicle Loading
338 STARTING AND OPERATING WARNING! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank filled. • Never add fuel to the vehicle when the engine is running. • A fire may result if gasoline is pumped into a portable container that is inside of a vehicle.
Page 339: Gross Vehicle Weight Rating (Gvwr)
• Vehicle Identification Number (VIN) • Type of Vehicle • Month Day and Hour of Manufacture (MDH) The bar code allows a computer scanner to read the Vehicle Identification Number (VIN). Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. This includes driver, passengers, and cargo.
Page 340: Loading
340 STARTING AND OPERATING Figure out the weight on the front and rear of the vehicle separately. It is important that you distribute the load evenly over the front and rear axles. Overloading can cause potential safety hazards and shorten useful service life. Heavier axles or suspension components do not necessarily increase the vehicle’s GVWR.
Page 341: Trailer Towing
Example Only Front Axle Empty Weight 2140 lbs Load (Including driver, pass- 360 lbs sengers and cargo) Total 2500 lbs GAWR 2544 lbs TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.
Page 342: Towing Requirements
342 STARTING AND OPERATING Towing Requirements • The maximum frontal area of the trailer cannot exceed 40 square feet (3.72 square meters). • The trailer tongue load must be considered as part of the combined weight of occupants and cargo, and should never exceed the weight referenced on the Tire and Loading Information placard.
Page 343 TRAVEL CONDITION UP TO 2 PERSONS & LUGGAGE 3 TO 5 PERSONS & LUGGAGE 6 TO 7 PERSONS & LUGGAGE * For vehicles equipped with store in the floor seating, the gross trailer weight must be reduced by 100 lbs (45 kg).
Page 344 344 STARTING AND OPERATING CAUTION! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances.
Page 345: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....346 If Your Engine Overheats ....347 Jacking And Tire Changing .
Page 346: Hazard Warning Flasher
346 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The hazard flasher switch is located in the center of the instrument panel above the radio. Hazard Flasher Switch To engage the Hazard Warning Flashers, depress the switch on the instrument panel. When the Hazard Warn- ing Switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emer- gency.
Page 347: If Your Engine Overheats
IF YOUR ENGINE OVERHEATS In any of the following situations, you can reduce the potential for overheating by taking the appropriate ac- tion. • On the highways — Slow down. • In city traffic — While stopped, put transmission in neutral, but do not increase engine idle speed.
Page 348: Jacking And Tire Changing
348 WHAT TO DO IN EMERGENCIES WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, see Section 7, Maintenance, of this manual.
Page 349: Jacking Instructions - Fold-In-Floor Seating
Jacking Instructions — Fold-in-Floor Seating Preparations For Jacking Park the vehicle on a firm level surface, avoid ice or slippery areas, set the parking brake and place the gear selector in PARK. Turn OFF the ignition. WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic.
Page 350 350 WHAT TO DO IN EMERGENCIES Jack Location — Fold-in-Floor Seating The jack, jack handle and winch handle tools are stowed behind the rear left side trim panel in the rear cargo area. Pull up on the lever to release the cover. Jack Location Remove the scissors jack and jack handle by rotating the small wing nut to the left.
Page 351 WHAT TO DO IN EMERGENCIES 351 Spare Tire Stowage — Fold-in-Floor Seating For vehicles equipped with fold-in-floor seating, the spare tire is stowed inside a protective cover located under the center of the vehicle by means of a cable winch mechanism.
Page 352 352 WHAT TO DO IN EMERGENCIES Jacking Instructions — Fold-in-Floor Seating 1. Loosen (but do not remove) the wheel lug nuts by turning them to the left one turn while the wheel is still on the ground. 2. To remove the compact spare tire/cover assembly, assemble the winch handle extensions to form a “T’...
Page 353 CAUTION! The winch mechanism is designed for use with the winch “T” handle only. Use of an air wrench or other power tools is not recommended and can damage the winch. 3. Assemble the winch handle extensions to form the Spare Tire Hook and pull the compact spare tire/cover assembly from under the vehicle.
Page 354 354 WHAT TO DO IN EMERGENCIES NOTE: If either front tire is flat, it may be necessary to jack up the vehicle to remove the compact spare tire/ cover assembly from under the vehicle. Refer to jack engagement locations in the following steps for proper jack placement.
Page 355 WHAT TO DO IN EMERGENCIES 355 Jack Engagement Locations...
Page 356 356 WHAT TO DO IN EMERGENCIES 6. These locations are on the sill flange of the body and consist of a pair of downstanding tabs. The jack is to be located, engaging the flange, between the pair of tabs closest to the wheel to be changed. Place the wrench on the jack screw and turn to the right until the jack head is properly engaged in the described location.
Page 357 10. Lower the vehicle by turning the jack screw to the left. 11. Finish tightening the lug nuts. Push down on the wrench while tightening for increased leverage. Alternate lug nuts until each nut has been tightened twice. Correct wheel nut tightness is 130 N·m (95 ft. lbs). If in doubt about the correct tightness, have them checked with a torque wrench by your dealer or at a service station.
Page 358 358 WHAT TO DO IN EMERGENCIES 14. Stow the cable and wheel spacer before driving the vehicle, reassemble the winch handle extensions to form a “T’ and fit the winch “T” handle over the drive nut. Rotate the nut to the right approximately 33 turns until the winch mechanism clicks at least three times.
Page 359 Spare Tire Removal WHAT TO DO IN EMERGENCIES 359 WARNING! A loose compact spare tire/cover assembly, thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the com- pact spare tire with the cover assembly in the place provided.
Page 360 360 WHAT TO DO IN EMERGENCIES 3. Turn the compact spare tire so that the valve stem is down and place the tire into the spare tire cover assem- bly. Slide the wheel spacer through the center of the wheel and spare tire cover assembly so that the two retainer tabs snap out and engage the spare tire cover on the opposite side.
Page 361: Jacking Instructions - Non Fold-In-Floor Seating
CAUTION! For vehicles equipped with fold-in-floor seating, the Winch Mechanism is designed specifically to stow a COMPACT Spare Tire ONLY. Do not attempt to use the Winch to stow the Full Size ’Flat’ Tire, or any other Full Size Tire. Vehicle damage may result. Jacking Instructions —...
Page 362 362 WHAT TO DO IN EMERGENCIES Jack Location — Non Fold-in-Floor Seating The jack, jack handle are stowed behind the rear left side trim panel in the rear cargo area. Pull up on the lever to release the cover. Remove the spare wheel, scissors jack and jack handle from stowage by rotating the wing nut to the left.
Page 363 Lowering Spare Tire Jacking Instructions — Non Fold-in-Floor Seating 1. Loosen (but do not remove) the wheel lug nuts by turning them to the left one turn while the wheel is still on the ground. WHAT TO DO IN EMERGENCIES 363 2.
Page 364 364 WHAT TO DO IN EMERGENCIES Jack Engagement Locations...
Page 365 5. These locations are on the sill flange of the body and consist of a pair of downstanding tabs. The jack is to be located, engaging the flange, between the pair of tabs closest to the wheel to be changed. Place the wrench on the jack screw and turn to the right until the jack head is properly engaged in the described location.
Page 366 366 WHAT TO DO IN EMERGENCIES NOTE: Do not install the wheel cover on the compact spare. Do not use a hammer or force to install the wheel covers. 9. Lower the vehicle by turning the jack screw to the left. 10.
Page 367: Jump-Starting Procedures If Battery Is Low
• For convenience in checking the spare tire inflation, stow with the valve stem toward the rear of the vehicle. • Using the jack handle, rotate the drive nut to the right until the wheel is drawn into place against the underside of the vehicle.
Page 368 368 WHAT TO DO IN EMERGENCIES WARNING! • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmis- sion cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
Page 369: Driving On Slippery Surfaces
5. Connect the other cable, first to the negative terminal of the booster battery and then to the engine of the vehicle with the discharged battery. Make sure you have a good contact on the engine. 6. Start the engine in the vehicle which has the booster battery, let the engine idle a few minutes, then start the engine in the vehicle with the discharged battery.
Page 370: Freeing A Stuck Vehicle
370 WHAT TO DO IN EMERGENCIES 2. Slow down if road has standing water or puddles. 3. Replace tires when tread wear indicators first become visible. 4. Keep tires properly inflated. 5. Maintain sufficient distance between your vehicle and the vehicle in front to avoid a collision in a sudden stop. FREEING A STUCK VEHICLE If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a rocking motion.
Page 371: Towing A Disabled Vehicle
TOWING A DISABLED VEHICLE With Ignition Key Your vehicle may be towed under the following condi- tions: The gear selector must be in NEUTRAL, the distance to be traveled must not exceed 100 miles (160 km), and the towing speed must not exceed 44 mph (72 km/h).
Page 372: Without The Ignition Key
372 WHAT TO DO IN EMERGENCIES If it is necessary to use the accessories while being towed (wipers, defrosters, etc.), the key must be in the ON position, not the ACCESSORY position. Make certain the transmission remains in NEUTRAL. Without The Ignition Key Special care must be taken when the vehicle is towed with the ignition in the LOCK position.
Page 373: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS 3.3L/3.8L Engines ..... . 376 Onboard Diagnostic System — OBD II ..377 Emissions Inspection And Maintenance Programs .
Page 374 374 MAINTAINING YOUR VEHICLE Steering Shaft Seal ....391 Steering Linkage ..... . 391 Drive Shaft Universal Joints .
Page 375 Rear Tail, Stop, Turn Signal, Side Marker And Back-Up Lights ..... . . 420 Center High Mounted Stop Light (CHMSL) . . . 421 License Light .
Page 376: 3.3L/3.8L Engines
376 MAINTAINING YOUR VEHICLE 3.3L/3.8L ENGINES Engine Compartment 3.3L/3.8L Engines...
Page 377: Onboard Diagnostic System - Obd Ii
ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emis- sions well within current government regulations.
Page 378: Emissions Inspection And Maintenance Programs
378 MAINTAINING YOUR VEHICLE EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the MIL (Malfunction Indicator Lamp) is functioning and is not on when the engine is running,...
Page 379: Replacement Parts
ignition key or start the engine. This means that your vehicle’s OBD system is not ready and you should not proceed to the I/M station. b. The MIL will not flash at all and will remain fully illuminated until you turn off the ignition key or start the engine.
Page 380: Maintenance Procedures
380 MAINTAINING YOUR VEHICLE NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment.
Page 381 The best time to check the engine oil level is about 5 minutes after a fully warmed engine is shut off or before starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings.
Page 382 382 MAINTAINING YOUR VEHICLE Change Engine Oil Road conditions and your kind of driving affects the interval at which your oil should be changed. Check the following list to see if any apply to you. • Day or night temperatures are below 32°F (0°C). •...
Page 383 American Petroleum Institute (API) Engine Oil Identification Symbol This symbol means that the oil has been certified by the American Petroleum Institute (API). The manufacturer only recommends API Certified engine oils. Engine Oil Viscosity (SAE Grade) SAE 5W-20 engine oil is recommended for all operating temperatures.
Page 384: Engine Oil Filter
384 MAINTAINING YOUR VEHICLE Disposing of Used Engine Oil And Oil Filters Care should be taken in disposing of used engine oil and oil filters from your vehicle. Used oil and oil filters, indiscriminately discarded, can present a problem to the environment.
Page 385: Spark Plugs
Spark Plugs Spark plugs must fire properly to assure engine perfor- mance and emission control. New plugs should be in- stalled at the specified mileage. The entire set should be replaced if there is any malfunction due to a faulty spark plug, malfunctioning spark plugs can damage the cata- lytic converter.
Page 386 386 MAINTAINING YOUR VEHICLE Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition.
Page 387: Maintenance-Free Battery
vehicle allowed to cool. Thereafter, service, including a tune-up to manufacturer’s specifications, should be ob- tained immediately. To minimize the possibility of catalyst damage: • Do not shut off the engine or interrupt the ignition when the transmission is in gear and the vehicle is in motion.
Page 388 388 MAINTAINING YOUR VEHICLE WARNING! Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water.
Page 389: Air Conditioner Maintenance
Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an Authorized Dealer at the start of each warm season. This service should include cleaning of the condenser fins and a system performance check. Drive belt tension should also be checked at this time.
Page 390: Power Steering - Fluid Check
390 MAINTAINING YOUR VEHICLE Refrigerant Recovery And Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocar- bon (HFC) that is endorsed by the Environmental Pro- tection Agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by dealers or other service facilities using recovery and recycling equipment.
Page 391: Front Suspension Ball Joints
WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to insure accurate fluid level reading. Do not overfill. Use only manufacturers recommended power steering fluid. If necessary, add fluid to restore to the proper indicated level.
Page 392: Body Lubrication
392 MAINTAINING YOUR VEHICLE Continued operation could result in failure of the univer- sal joint due to water and dirt contamination of the grease. This would require complete replacement of the joint assembly. Body Lubrication Locks and all body pivot points, including such items as seat tracks, doors, liftgate, sliding doors and hood hinges, should be lubricated periodically to assure quiet, easy operation and to protect against rust and wear.
Page 393: Windshield And Rear Window Washers
Windshield and Rear Window Washers The fluid reservoir for the windshield washers and the rear window washer is shared. It is located in the engine compartment and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) and operate the system for a few seconds to flush out the residual water.
Page 394: Cooling System
394 MAINTAINING YOUR VEHICLE vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment.
Page 395 Coolant Checks Check engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If coolant is dirty or rusty in appearance, the system should be drained, flushed and refilled with fresh coolant. Check the front of the A/C condenser for any accumulation of bugs, leaves, etc.
Page 396 396 MAINTAINING YOUR VEHICLE CAUTION! • Mixing of coolants other than specified engine coolant, may result in engine damage, and de- crease corrosion protection. If a non-HOAT cool- ant is introduced into the cooling system in an emergency, it should be replaced with the speci- fied coolant as soon as possible.
Page 397 Cooling System Pressure Cap The cap must be fully tightened to prevent loss of coolant, and to insure that coolant will return to the radiator from the coolant recovery bottle. The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces.
Page 398 398 MAINTAINING YOUR VEHICLE do not store ethylene glycol based engine coolant in open containers or allow it to remain in puddles on the ground. If ingested by a child, contact a physician immediately. Clean up any ground spills immediately. Coolant Level The coolant recovery bottle provides a quick visual method for determining that the coolant level is ad-...
Page 399: Hoses And Vacuum/Vapor Harnesses
• Check coolant freeze point in the radiator and in the coolant recovery bottle. If antifreeze needs to be added, contents of coolant recovery bottle must also be protected against freezing. • If frequent coolant additions are required, or if the level in the coolant recovery bottle does not drop when the engine cools, the cooling system should be pres- sure tested for leaks.
Page 400: Brakes
400 MAINTAINING YOUR VEHICLE Insure nylon tubing in these areas has not melted or collapsed. Inspect all hose connections such as clamps and cou- plings to make sure they are secure and no leaks are present. Components should be replaced immediately if there is any evidence of wear or damage that could cause failure.
Page 401: Master Cylinder - Abs Brakes Brake Fluid Level Check
Insure nylon tubing in these areas has not melted or collapsed. Inspect all hose connections such as clamps and cou- plings to make sure they are secure and no leaks are present. NOTE: Often, fluid such as oil, power steering fluid, and brake fluid are used during assembly plant opera- tions to facilitate the assembly of hoses to couplings.
Page 402 402 MAINTAINING YOUR VEHICLE Overfilling of fluid is not recommended because it may cause leaking in the system. Add enough fluid to bring the level up to the require- ments described on the brake fluid reservoir. With disc brakes, fluid level can be expected to fall as the brake pads wear.
Page 403: Fuel System Hoses
Fuel System Hoses Electronic Fuel Injection high pressure fuel systems are designed with hoses which have unique material charac- teristics to provide adequate sealing and resist attack by deteriorated gasoline. Use only the manufacturers specified hoses in any fuel system servicing. It is mandatory to replace all clamps that have been loosened or removed during service.
Page 404 404 MAINTAINING YOUR VEHICLE CAUTION! Using a transmission fluid other than the manufac- turers recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturers recommended fluid will result in more frequent fluid and filter changes.
Page 405 5. Remove the dipstick and determine if the fluid is hot or warm. Hot fluid is approximately 180°F (82°C), which is the normal operating temperature after the vehicle has been driven at least 15 miles (24 km). The fluid cannot be comfortably held between the finger tips.
Page 406: Front And Rear Wheel Bearings
406 MAINTAINING YOUR VEHICLE • Police, taxi, limousine, commercial type operation, or trailer towing where the vehicle is driven regularly for more than 45 minutes of continuous operation. NOTE: Refer to Section 8 of this manual for Mainte- nance Schedules. If the transmission is disassembled for any reason, the fluid and filter should be changed.
Page 407 The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: •...
Page 408 408 MAINTAINING YOUR VEHICLE CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.
Page 409 • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. • Use Mopar touch up paint on scratches as soon as possible. Your dealer has touch up paint to match the color of your vehicle.
Page 410 410 MAINTAINING YOUR VEHICLE 1. Remove all dirt with a wet soft rag. A mild soap solution may be used, do not use high alcohol content or abrasive cleaners. Glass cleaners are not recommended. If soap is used, wipe clean with a clean damp rag. 2.
Page 411: Cleaning The Instrument Panel And Underseat Cup Holders
If the belts need cleaning, use a mild soap solution or lukewarm water. Do not remove the belts from the car to wash them. Replace the belts if they appear frayed or worn or if the buckles do not work properly. Cleaning The Instrument Panel and Underseat Cup Holders Removal...
Page 412: Integrated Power Module (Ipm)
412 MAINTAINING YOUR VEHICLE Cleaning Soak the drawer, with the drawer front facing up, in a mixture of medium hot tap water and one teaspoon of mild liquid dish soap. Let soak for approximately one hour. After one hour pull the drawer from the water and dip it back into the water about six times.
Page 413 Cavity Maxi Fuse Description 30 Amp Front Wipers Pink 40 Amp Anti-Lock Brake System Green (ABS) Pump 40 Amp Front Blower Green 40 Amp Electronic Back Light (EBL) Green 40 Amp Body Control Module Green (BCM) Feed 1 30 Amp Central Amplifier Pink 30 Amp...
Page 414 414 MAINTAINING YOUR VEHICLE Cavity Mini Fuse 20 Amp Yel- Fog Lights 15 Amp Blue Left Park/Tail Light 15 Amp Blue Right Park/Tail Light 20 Amp Yel- RDO/IP Ignition 20 Amp Yel- 12 Volt Out Ignition or Battery 20 Amp Yel- Horn 20 Amp Yel- EWD/ Rear Wiper...
Page 415: Vehicle Storage
CAUTION! • When installing the Integrated Power Module cover, it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the Integrated Power Module, and possibly result in a electrical system failure.
Page 416: Replacement Light Bulbs
416 MAINTAINING YOUR VEHICLE air conditioning system at idle for about five minutes in the fresh air and high blower setting. This will insure adequate system lubrication to minimize the possibility of compressor damage when the system is started again. REPLACEMENT LIGHT BULBS LIGHT BULBS —...
Page 417: Bulb Replacement
BULB REPLACEMENT Headlights 1. Remove the three screws securing the headlight mod- ule. 2. Turn the bulb socket retaining ring or the bulb assem- bly counterclockwise. MAINTAINING YOUR VEHICLE 417 3. Disconnect the electrical connector and replace the bulb. NOTE: On some vehicles it may be necessary to slide the red release lock rearward and push forward on the connector while depressing the release tab.
Page 418: Front Park/Turn Signal And Sidemarker Lights
418 MAINTAINING YOUR VEHICLE CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with an oily surface, clean the bulb with rubbing alcohol. Front Park/Turn Signal and Sidemarker Lights 1.
Page 419: Front Fog Light
2. Twist the turn signal socket to remove from the headlight module and pull bulb from socket. 3. Replace bulb, reinstall socket and then reinstall the headlight module. MAINTAINING YOUR VEHICLE 419 Front Fog Light 1. Reach behind the front fascia from under the vehicle. 2.
Page 420: Rear Tail, Stop, Turn Signal, Side Marker And Back-Up Lights
420 MAINTAINING YOUR VEHICLE Rear Tail, Stop, Turn Signal, Side Marker and Back-up Lights 1. Raise the liftgate. 2. Remove the two tail light assembly push-in type fasteners, by prying under the fastener head with a large flat screwdriver. 3. Squeeze the socket assembly tabs to remove it from the housing.
Page 421: Center High Mounted Stop Light (Chmsl)
Center High Mounted Stop Light (CHMSL) 1. Remove the two screws securing the CHMSL. MAINTAINING YOUR VEHICLE 421 2. Twist the bulb socket to remove from the CHMSL housing. 3. Pull the bulb out of the socket. 4. Replace the bulb, reinstall the socket and reattach the CHMSL.
Page 422: Fluids And Capacities
422 MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES Fuel (Approximate) 87 Octane Engine Oil-with filter 3.3 & 3.8 Liter Engines (SAE 5W-20, API Certified) Cooling System * 3.3 & 3.8 Liter Engines (Mopar Antifreeze/Coolant 5 Year/ 100,000 Mile Formula) * Includes heater and coolant recovery bottle filled to MAX level. * Add 2.9 quarts (2.8 liters) if equipped with a rear heater.
Page 423: Recommended Fluids, Lubricants And Genuine Parts
RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Fluids, Lubricants and Genuine Parts Engine Coolant Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Or- ganic Additive Technology) Engine Oil Use API Certified SAE 5W-20 engine oil. Refer to your oil filler cap for cor- rect SAE grade, meeting DaimlerChrysler Material Standard MS-6395.
Page 424: Chassis
424 MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts. Mopar ATF+4 Automatic Transmission Fluid. Mopar DOT 3, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids.
Page 425 MAINTENANCE SCHEDULES CONTENTS Emission Control System Maintenance ..426 Maintenance Schedules ....426 Schedule “B” ......429 Schedule “A”...
Page 426: Emission Control System Maintenance
426 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
Page 427 • Taxi, police, or delivery service (commercial ser- vice). • Off-road or desert operation. NOTE: Most vehicles are operated under the conditions listed for Schedule B . Second is Schedule “A”. It is for vehicles that are not operated under any of the conditions listed under Sched- ule B .
Page 428 428 MAINTENANCE SCHEDULES Once a Month • Check tire pressure and look for unusual wear or damage. • Inspect the battery and clean and tighten the terminals as required. • Check the fluid levels of coolant reservoir, brake master cylinder and transmission, add as needed. •...
Page 429: Schedule "B" 429
SCHEDULE “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. Change the automatic transmission fluid and filter every 60,000 miles (96 000 km) if the vehicle is usually operated under one or more of the conditions marked with an •...
Page 430 430 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. * Replace the air conditioning filter. 3, 000 6, 000 9, 000...
Page 431 Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace as neces- sary.* Replace the air conditioning filter.
Page 432 432 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. * Replace the air conditioning filter. 39, 000 42, 000 45, 000...
Page 433 Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if neces- sary.* Inspect the serpentine drive belt on 3.3 liter and 3.8 liter engines, replace if necessary.
Page 434 434 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter Replace the spark plugs on 3.3 liter and 3.8 liter engines.
Page 435 Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter * Inspect the serpentine drive belt on 3.3 liter and 3.8 liter engines, replace if necessary.
Page 436 436 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace as necessary.* Inspect the serpentine drive belt on 3.3 liter and 3.8 liter engines, replace if necessary.
Page 437: Schedule "A" 437
SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. Replace the air conditioning filter.
Page 438 438 SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. Check the PCV valve and replace, if neces- sary.* Inspect the serpentine drive belt on 3.3 liter...
Page 439 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if neces- sary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. Check and replace the PCV valve , if necessary.* Inspect the serpentine drive belt on 3.3 liter and 3.8 liter engines, replace if necessary.
Page 440 440 SCHEDULE “A” Miles (Kilometers) [Months] Flush and replace the engine coolant at 100,000 miles, if not done at 60 months. Replace the air conditioning filter. 78, 000 84, 000 90, 000 (125 000) (134 000) (144 000) [78] [84] [90] 96, 000 100, 000...
Page 441 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. Check the PCV valve and replace, if necessary.* Inspect the serpentine drive belt on 3.3 liter and 3.8 liter engines, replace if necessary.
Page 442 442 SCHEDULE “A” * This maintenance is recommended by the manufacture to the owner but is not required to maintain the emis- sions warranty. ‡ This maintenance is not required if previously replaced. Inspection and service should also be performed anytime a malfunction is observed or suspected.
Page 443: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle ..... . . 444 Prepare For The Appointment ... . 444 Prepare A List .
Page 444: Suggestions For Obtaining Service For Your Vehicle
444 IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager.
Page 445: If You Need Assistance
We want you to be happy with our products and services. Warranty service must be done by an authorized Chrysler, Dodge, or Jeep dealer. We strongly recommend that you take your vehicle to you selling dealer. They know you and your vehicle best, and are most concerned that you get prompt and high quality service.
Page 446 446 IF YOU NEED CONSUMER ASSISTANCE DaimlerChrysler Motors Corporation Customer Center P.O. Box 21–8004 Auburn Hills, MI 48321–8004 Phone: (800) 992-1997 DaimlerChrysler Canada Inc. Customer Center P.O. Box 1621 Windsor, Ontario N9A 4H6 Phone —(800) 465–2001 In Mexico contact: Av. Prolongacion Paseo de la Reforma, 1240 Sante Fe C.P.
Page 447: Warranty Information
contract, call the manufacturer’s Service Contract Na- tional Customer Hotline at 1-800-521-9922. The manufacturer will not stand behind any service contract that is not the manufacturer’s Service Contract. It is not responsible for any service contract other than the manufacturer’s Service Contract. If you purchased a service contract that is not a manufacturer’s Service Contract, and you require service after your manufactur- er’s new vehicle limited warranty expires, please refer to...
Page 448 448 IF YOU NEED CONSUMER ASSISTANCE U.S. ONLY...
Page 449: Mopar Parts
MOPAR PARTS Mopar fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administra- tion (NHTSA) in addition to notifying the manufacturer.
Page 450: Publication Order Forms
• Owner’s Manuals. These manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific Chrysler group vehicles. Included are starting, operating, emergency and maintenance pro- cedures as well as specifications, capabilities and safety tips.
Page 451: Department Of Transportation Uniform Tire Quality Grades
Call Toll Free at 1–800–890–4038 (U.S.) or 1–800–387–1143 (Canada) Visit us on the World Wide Web at: www.techauthority.daimlerchrysler.com or www.daimlerchrysler.ca/manuals DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories estab- lished by the National highway Traffic Safety Adminis- tration.
Page 452: Temperature Grades
452 IF YOU NEED CONSUMER ASSISTANCE WARNING! The traction grade is based on braking (straight- ahead) traction tests and does not include cornering (turning) performance. Temperature Grades The temperature grades are A (highest), B, and C, repre- senting the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Page 453 INDEX...
Page 454 454 INDEX Adding Fuel ......336 Adding Washer Fluid ....290,393 Additives, Fuel .
Page 455 Interlock System ..... . . 300 Reset Mode ......301 Selection Of Lubricant .
Page 456 456 INDEX Caps, Filler Fuel ....... . 336 Oil (Engine) ......383 Radiator (Coolant Pressure) .
Page 457 Computer, Trip/Travel ....158 Console, Overhead ..... . . 154 Console, Removable .
Page 458 458 INDEX Door Locks, Automatic ....19 Door Opener, Garage ..... 163 Drive Belts .
Page 459 Temperature Gauge ..... 203 Exhaust Gas Caution ....38,83,335,394 Exhaust System .
Page 460 460 INDEX Fuel System Caution ..... 334 Fueling ....... 336 Fuses .
Page 461 Ignition Key ....... . . 12 Illuminated Entry ......16 Immobilizer .
Page 462 462 INDEX Lead Free Gasoline ..... . 332 Liftgate ....... . 35 Lights .
Page 463 Service ......416,417 Service Engine Soon (Malfunction Indicator) . . . 205 Side Marker ......420 Theft Alarm .
Page 464 464 INDEX Outside ......94 Rearview ......92 Vanity .
Page 465 Parking On Hill ......303 Passing Light ......143 Pedals, Adjustable .
Page 466 466 INDEX Rear Seat Removal ....124,126 Rear Seating Flexibility ....128,130 Rear Window Defroster .
Page 467 And Pregnant Women ....53 Center Lap Belt ......51 Child Restraint .
Page 468 468 INDEX Spark Plugs ......385 Speed Control ......151 Speedometer .
Page 469 Tire Identification Number (TIN) ... . . 313 Tire Markings ......310 Tire Safety Information .
Page 470 470 INDEX Selection of Lubricant ....403,424 Transmission ......403 Automatic .
Page 471 Washing Vehicle ......407 Wheel Alignment and Balance ....326 Wheel and Wheel Trim .
Page 472 NOTES...

Chrysler 2005 Town and Country Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

Quick Links

INTRODUCTION

Chapters

Related Manuals for Chrysler 2005 Town and Country

Summary of Contents for Chrysler 2005 Town and Country