Advertisement
Quick Links
OutJ6nck
PC>WER'"
an EnerS y s compan y
Input/Output/Bypass Assembly
Purpose
This document provides information on how to install the Input/Output/Bypass
Assembly needed for a single-phase configuration using an OutBack GSLC
(GS Load Center) enclosure.
This product allows manual switching between a single Radian Series
lnverter/Charger and an AC source, facilitating maintenance and power
continuity. lt is intended to be installed within the GSLC or one of its variants.
Scope
This document covers how to install the input, output, and bypass circuit
breakers and the mechanical interlock onto the GSLC.
will
site-specific and
vary by installation.
alte red if they do not apply to a particular installation.
These instructions are for use by qualified personnel who meet all local and
governmental code requirements for licensing and training for the installation of
electrical power systems with AC and DC voltage up to 600 volts.
Requirements
Outßack Power's GS-IOB-230VAC is intended as a component for Outßack listed
UL508A or UL 1741 lndustrial Control Panels, specifically the GSLC variants. lt is
intended for indoor use only. This equipment is to be installed by qualified
GS Load Center Installation Manual
personnel only. Refer to the
installation instructions.
Grounding lnstructions
The enclosure for the GS-IOB-230VAC should be connected to a grounded,
permanent wiring system. The AC and DC circuits are not bonded to the
enclosure chassis. System grounding, when required by local codes, is the
responsibility of the installer. All installations should comply with all national and
local codes and ordinances.
The equipment ground is marked with this symbol:
900-0146-01-00 REV A
GS-IOB-230VAC
Installation lnstructions
Wiring requirements are
Certain steps may be omitted or
for complete
@
ALPHA
OUTBACK
ENERGV
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for EnerSys OutBack POWER ALPHA OUTBACK ENERGY GS-IOB-230VAC
Summary of Contents for EnerSys OutBack POWER ALPHA OUTBACK ENERGY GS-IOB-230VAC
- Page 1 OutJ6nck ALPHA OUTBACK PC>WER'" ENERGV an EnerS y s compan y GS-IOB-230VAC Input/Output/Bypass Assembly Installation lnstructions Purpose This document provides information on how to install the Input/Output/Bypass Assembly needed for a single-phase configuration using an OutBack GSLC (GS Load Center) enclosure. This product allows manual switching between a single Radian Series lnverter/Charger and an AC source, facilitating maintenance and power continuity.
-
Page 2: Tools Required
GS-IOB-230VAC Installation lnstructions Tools Required ► Philips Screwdriver ► Fiat Screwdriver ► Socket Set ► Digital multimeter (DMM) or ohmmeter Components IM I Figure 1 GS-1OB-230VAC Components 900-0146-01-00 REVA... - Page 3 GS-IOB-230VAC Installation lnstructions Table 1 Parts List ltem Quantity AC Circuit Breakers, single-pole (SO A, 250 Vac) with 6-32 x ¼" screws installed Label Set Installation lnstructions Hardware Kit: Bus Bars ► Bus Bar lnsulators, Blue ► Bus Bar lnsulators, Brown ►...
- Page 4 GS-IOB-230VAC Installation lnstructions lnstalling the Circuit Breakers and Mechanical Bypass Assembly The simplest method to install these devices is to remove the main circuit breaker bracket from the GSLC first. To remove the main bracket: Remove the front cover (sometimes called the "front door") of the GSLC. Open the door to 90 degrees and lift up about 1 /2"...
- Page 5 GS-IOB-230VAC Installation lnstructions Remove (x3) Main Bracket lnterior Cover Open to 90 degrees Remove (x3) Remove (x4) Figure 3 Removing the Covers and Main Bracket Once the main bracket has been removed, remove the top four knockouts. lnstall the circuit breakers and mechanical bypass according to these steps. Place each circuit breaker behind the bracket and orient it so that the numbers read correctly.
- Page 6 GS-IOB-230VAC Installation lnstructions Tighten until secure, but do not over-tighten. 7"°" Brackets facing inward Tabs"� Inner holes � Hole Bypass assembly Figure 4 lnstalling Mechanical Bypass Once installed, the plate will not allow both circuit breakers to be in the ON position.
- Page 7 —...
- Page 8 GS-IOB-230VAC Installation lnstructions J\Ct,1E, JFr. --------------... GROUt.lD ---•---•-..- ------------ •---------- ....,. GFUDINHOT - •-· -•- •-• - •-• - • -•-• ' AC OUT HOT•• - • � ·. -0 � ..__, 0.,,., ..ßypHS 8„0: fl fl- ,--..., �---<) 0-·...
- Page 9 About OutBack Power Technologies Outßack Power Technologies is a leader in advanced energy conversion technology. Outßack products include true sine wave inverter/chargers, maximum power point tracking charge controllers, and system communication components, as weil as circuit breakers, batteries, accessories, and assembled systems. Disclaimer UNLESS SPECIFICALL Y AGREED TO IN WRITING, OUTBACK POWER TECHNOLOGIES: (a) MAKES NO WARRANTY AS TO THE ACCURACY, SUFFICIENCY OR SUITABILITY OF ANY...
Need help?
Do you have a question about the OutBack POWER ALPHA OUTBACK ENERGY GS-IOB-230VAC and is the answer not in the manual?
Questions and answers