Table of Contents
Advertisement
Installation Guide
ProSpace
Packaged Terminal Air Conditioner
(PTAC)
Wall Sleeve Part Numbers: SLV00351, SLV00354,
SLV00355, SLV00356, SLV00357, SLV00358
Only qualified personnel should install and service the equipment. The installation, starting up, and servicing of heating, ventilating, and air-conditioning
equipment can be hazardous and requires specific knowledge and training. Improperly installed, adjusted or altered equipment by an unqualified person
could result in death or serious injury. When working on the equipment, observe all precautions in the literature and on the tags, stickers, and labels that
are attached to the equipment.
April 2020
™
S S A A F F E E T T Y Y W W A A R R N N I I N N G G
P P T T A A C C - - S S V V N N 0 0 2 2 8 8 E E - - E E N N
Advertisement
Table of Contents
Related Manuals for Trane Technologies ProSpace SLV00351
Summary of Contents for Trane Technologies ProSpace SLV00351
- Page 1 Installation Guide ProSpace ™ Packaged Terminal Air Conditioner (PTAC) Wall Sleeve Part Numbers: SLV00351, SLV00354, SLV00355, SLV00356, SLV00357, SLV00358 S S A A F F E E T T Y Y W W A A R R N N I I N N G G Only qualified personnel should install and service the equipment.
- Page 2 Introduction Read this manual thoroughly before operating or servicing this unit. Warnings, Cautions, and Notices Safety advisories appear throughout this manual as required. Your personal safety and the proper operation of this machine depend upon the strict observance of these precautions. The three types of advisories are defined as follows: Indicates a potentially hazardous situation which, if not avoided, could result in WARNING...
- Page 3 I I n n t t r r o o d d u u c c t t i i o o n n W W A A R R N N I I N N G G P P e e r r s s o o n n a a l l P P r r o o t t e e c c t t i i v v e e E E q q u u i i p p m m e e n n t t ( ( P P P P E E ) ) R R e e q q u u i i r r e e d d ! ! F F a a i i l l u u r r e e t t o o w w e e a a r r p p r r o o p p e e r r P P P P E E f f o o r r t t h h e e j j o o b b b b e e i i n n g g u u n n d d e e r r t t a a k k e e n n c c o o u u l l d d r r e e s s u u l l t t i i n n d d e e a a t t h h o o r r s s e e r r i i o o u u s s i i n n j j u u r r y y .
-
Page 4: Table Of Contents
Table of Contents Location, Dimensions, and Leveling ......... . . 5 General Notes . -
Page 5: Location, Dimensions, And Leveling
Location, Dimensions, and Leveling General Notes • Carefully handle the wall sleeve. • The cardboard stiffener inside the wall sleeve (if present) and the rear protective panel must remain in place until ready to install the chassis to ensure case rigidity. •... -
Page 6: Locating The Wall Sleeve
L L o o c c a a t t i i o o n n , , D D i i m m e e n n s s i i o o n n s s , , a a n n d d L L e e v v e e l l i i n n g g Locating the Wall Sleeve N N o o t t e e : : Care should be taken in the location of the electrical entry in relationship to the wall sleeve to ensure access to power once the unit is installed. -
Page 7: Preparation
Preparation Preparing the Wall The wall sleeve should be installed during construction and lintels should be used to support the block above the wall sleeve. The wall sleeve will not support the concrete block or brick. The wall sleeve is modular in height and width: •... -
Page 8: Preparing The Case
P P r r e e p p a a r r a a t t i i o o n n Preparing the Case N N o o t t e e : : Do not remove the cardboard stiffener inside the wall sleeve (if present) until the chassis is installed. -
Page 9: Installation
Installation Installing the Wall Sleeve in Wall Opening 1. Position the wall sleeve into the wall. The rear (outside) edge of the wall sleeve should extend at least 1/4” beyond the outside wall in order to properly caulk, prevent sealing the drain holes in the rear flange of the case, and to facilitate easy installation of an accessory drain (if desired). -
Page 10: Installing Foam Gasket On Extended Wall Sleeve
I I n n s s t t a a l l l l a a t t i i o o n n Installing Foam Gasket on Extended Wall Sleeve (As Required for Standard Vertical Louvered Grilles) 1. Measure and cut to length, two (2) strips of adhesive backed foam gasket to apply to the supports of the extended wall sleeve. -
Page 11: Installing In Extra Thick Walls
I I n n s s t t a a l l l l a a t t i i o o n n Installing in Extra Thick Walls If the wall sleeve is being installed in a thick wall where the wall sleeve is recessed more than 3 inches, an extended wall sleeve will be required with depths as stipulated in the section, “Preparing the Wall,”... -
Page 12: Electrical Requirements For 208/230V And 265V
I I n n s s t t a a l l l l a a t t i i o o n n Electrical Requirements for 208/230V and 265V • 2 2 0 0 8 8 V V / / 2 2 3 3 0 0 V V : : Provisions should be made to have the proper electrical outlet near the case. All wiring should be made in accordance with local codes and regulations. - Page 13 N N o o t t e e s s PTAC-SVN028E-EN...
- Page 14 N N o o t t e e s s PTAC-SVN028E-EN...
- Page 15 N N o o t t e e s s PTAC-SVN028E-EN...
- Page 16 Trane - by Trane Technologies (NYSE: TT), a global innovator - creates comfortable, energy efficient indoor environments for commercial and residential applications. For more information, please visit trane.com or tranetechnologies.com. Trane has a policy of continuous product and product data improvements and reserves the right to change design and specifications without notice.
Need help?
Do you have a question about the ProSpace SLV00351 and is the answer not in the manual?
Questions and answers