Table of Contents
Advertisement
ACCESSORIES
•
SKIL can assure flawless functioning of the tool only
when original accessories are used
•
For mounting/using non-SKIL accessories observe the
instructions of the manufacturer concerned
•
Use only grinding/cutting discs with a maximum
thickness of 6 mm and a spindle hole diameter of
22 mm
•
Never use reducors or adaptors to fit large-hole grinding/
cutting discs
•
Never use accessories with a "blind" threaded hole
smaller than M14 x 21 mm
•
Handle and store grinding/cutting discs carefully to avoid
chipping and cracking
BEFORE USE
•
Before using the tool for the first time, it is recommended
to receive practical information
•
Always mount auxiliary handle and protective guard ;
never use the tool without them
•
Use suitable detectors to find hidden utility lines
or call the local utility company for assistance
(contact with electric lines can lead to fire or electrical
shock; damaging a gas line can result in an explosion;
penetrating a water pipe will cause property damage or
an electrical shock)
•
Do not work materials containing asbestos (asbestos
is considered carcinogenic)
•
Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator or
bystanders); wear a dust mask and work with a dust
extraction device when connectable
•
Certain kinds of dust are classified as carcinogenic
(such as oak and beech dust) especially in conjunction
with additives for wood conditioning; wear a dust
mask and work with a dust extraction device when
connectable
•
Follow the dust-related national requirements for the
materials you want to work with
•
Be careful when cutting grooves, especially in supporting
walls (slots in supporting walls are subject to country-
specific regulations; these regulations are to be observed
under all circumstances)
Secure the workpiece (a workpiece clamped with
•
clamping devices or in a vice is held more securely than
by hand)
•
Do not clamp the tool in a vice
DURING USE
•
In case of electrical or mechanical malfunction,
immediately switch off the tool and remove battery
•
In case of a battery protection cut off, or when the
battery is removed, the tool will not restart on its own; for
restarting the tool unlock on/off switch and switch on tool
again 9
AFTER USE
•
After switching off the tool, never stop the rotation of the
accessory by a lateral force applied against it
BATTERIES
•
Only use the following batteries and chargers with
this tool
- SKIL battery: BY5197E-03 BY5196E-03
- SKIL charger: SC5358E-01 QC5360E-01 QC5359E-00
•
Do not use the battery when damaged; it should be
replaced
•
Do not disassemble the battery
•
Do not expose tool/battery to rain
•
Permitted ambient temperature (tool/charger/battery):
- when charging 4...40°C
- during operation –20...+50°C
- during storage –20...+50°C
EXPLANATION OF SYMBOLS ON TOOL/BATTERY
3 Read the instruction manual before use
4 Wear protective glasses and hearing protection
5 Do not dispose of electric tools and batteries together
with household waste material
USE
•
Charging battery
! read the safety warnings and instructions
provided with the charger
•
Removing/installing the battery 1
•
Mounting of accessories 1
! remove battery from tool
- clean spindle and all parts to be mounted
- tighten clamping flange with spanner while pushing
spindle-lock button
! push spindle-lock button only when spindle is at
a standstill
- for removing accessories handle vice-versa
! grinding/cutting discs become very hot during
use; do not touch them until they have cooled
down
! never use a grinding/cutting disc without the label
("blotter") which is glued onto it (if provided)
•
Mounting of auxiliary handle 6
! remove battery from tool
- screw auxiliary handle on the right, the top, or the left of
the tool (depending on the work to be carried out)
•
Removing/mounting/adjusting of protective guard 7
! remove battery from tool
! ensure that the closed side of the protective guard
always points to the operator
- if necessary, adjust protective guard by tightening
screw which is pre-set at manufacturing (ensure that
the protective guard is closed)
•
Before using the tool
- ensure that accessory is correctly mounted and firmly
tightened
- check if accessory runs freely by turning it by hand
- test-run tool for at least 60 seconds at highest no-load
speed in a safe position
- stop immediately in case of considerable vibration or
other defects and check tool to determine the cause
•
On/off locking switch 8
- switch on tool 8 a
! be aware of the sudden impact when the tool is
switched on
! before the accessory reaches the workpiece, the
tool should run at full speed
- lock switch 8 b
- unlock switch/switch off tool 8 c
! before switching off the tool, you should lift it from
the workpiece
! the accessory continues to rotate for a short time
after the tool has been switched off
10
Advertisement
Table of Contents
