Parts Description; Important Safety Information - Rinnai REI-E380NP-B-WH Instructions For Use, Installation, And Connection

PARTS DESCRIPTION

1
7
8
2
4
5
3
9
10
6
11
23
HANDSHOWER
ACCESSORIES
1. Front Cover
2. LED Indicators
3. ELCB Test & Reset Button
4. Pump Control Knob
5. Temperature Control Knob
6. Stop Valve
7. Rail Support/ Wall Bracket
8. Handshower
9. Adjustable Shower Holder
10. Sliding Rail
11. PVC Hose 1.5m
12. Shower Bracket
13. Heater Base
14. Thermostat
13 13
17
14 14
15
15
18
18 20
25
21
16
16
22
19
19
6
23
NO PUMP MODEL DC PUMP MODEL
8
12
11
CAUTION
Please read the enclosed instructions
completely before connecting,
operating and installing this product.
15. Heater Tank
16. PCB Board (Test&Reset)
17. Terminal Block
18. PCB Board
19. Water Outlet Connection
20. TRIAC
21. Water Inlet Connection
22. Reed Switch Assy
23. Mesh Filter
24. DC Pump
25. Pump Knob
3
WARNING !
1.1 Products manufactured by us are safe provided they are installed, used and
17
maintained in good working order in accordance with our instructions and
recommendations. Always refer to this manual if you have any doubt.
1.2 The appliance must be earthed. Improper grounding could cause electric shock.
24
1.3 If any of the following conditions occur, immediately switch o the mains and
contact the sales agent for repair. Never attempt to repair the unit yourself.
20
21 1.3.1 If the heater begins to make an odd noise, smell or smoke.
22
1.3.2 ELCB and heater lamp does not light up.
1.3.3 Water temperature can not be controlled.
6
1.3.4 If the heater shows signs of a distinct change in performance.
1.3.5 If found water leakage from inside.
23
1.4 For pump model, it is highly recommended to connect the water inlet connection to
tank storage supply otherwise it may cause damage to the pump motor.
1.5 The appliance is not intended for use by person (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
User is advised to test and adjust the water temperature before showering.
1.6 In time of lightning/thunder, switch "o " the electric supply to the shower unit
in advance to protect the shower unit against possible damage.
1.7 Metallic/chrome hose and conductive control valve shall not be used. (Malaysia
only)
Note: When removing the unit from package, small amount of water may be found inside.
This is normal as the unit is tested during manufacturing process.
CAUTION !
CAUTION !
2.1 Installation must be carried out by a qualified personnel and in compliance to
the local authority regulations.
2.2 This heater must be permanently connected to the direct main current supply.
The use of a plug and socket is not recommended.
2.3 For the correct size of wire conductor corresponding to di erent electrical
loading, please refer to Table 1.
2.4 This heater operates at a minimum water flow rate of 2.0ltr/min and maximum
working pressure of 6 bars. For direct connection to the water tank, the heater
must have a minimum distance of 1.0m below the water tank.
2.5 This heater will not function if there is insu cient water flow (min 2.0ltr/min) to
trigger the flow switch.
2.6 The built-in ELCB will automatically cut o the power supply in case there is a
current leakage of at least 15mA.
2.7 The thermostat will automatically cut o the power supply if it has sensed an
abnormal rise in water outlet temperature.

IMPORTANT SAFETY INFORMATION

4