Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Makita RS002GD201
Summary of Contents for Makita RS002GD201
- Page 1 INSTRUCTION MANUAL Cordless Rear Handle Saw RS002G Read before use.
-
Page 2: Specifications
SPECIFICATIONS Model: RS002G Blade diameter 260 mm Max. Cutting depth at 0° 95.0 mm at 45° bevel 70.0 mm at 56° bevel 54.5 mm No load speed 4,000 min Overall length 489 mm Rated voltage D.C. 36 V - 40 V max Net weight 5.7 - 6.3 kg •... -
Page 3: Ec Declaration Of Conformity
Electrical safety Vibration Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any The vibration total value (tri-axial vector sum) deter- adapter plugs with earthed (grounded) power mined according to EN62841-2-5: tools. Unmodified plugs and matching outlets will Work mode: cutting wood reduce risk of electric shock. Vibration emission (a ) : 2.5 m/s or less... - Page 4 Do not let familiarity gained from frequent use Keep handles and grasping surfaces dry, clean of tools allow you to become complacent and and free from oil and grease. Slippery handles ignore tool safety principles. A careless action can and grasping surfaces do not allow for safe handling cause severe injury within a fraction of a second.
- Page 5 Adjust the cutting depth to the thickness of When blade is binding, or when interrupting a the workpiece. Less than a full tooth of the blade cut for any reason, release the trigger and hold the saw motionless in the material until the teeth should be visible below the workpiece.
- Page 6 Place the wider portion of the saw base on that part of the workpiece which is solidly supported, not on the section that will fall off when the cut is made. If the workpiece is short or small, clamp it down. DO NOT TRY TO HOLD SHORT PIECES BY HAND! Never force the saw.
- Page 7 It may result in loss of your eyesight. CAUTION: Only use genuine Makita batteries. Do not short the battery cartridge: Use of non-genuine Makita batteries, or batteries that (1) Do not touch the terminals with any con- have been altered, may result in the battery bursting ductive material. causing fires, personal injury and damage. It will...
-
Page 8: Functional Description
26. Do not insert any devices other than Makita Tool / battery protection system wireless unit into the slot on the tool. 27. Do not use the tool with the lid of the slot damaged. Water, dust, and dirt come into the slot may cause malfunction. -
Page 9: Overload Protection
Overload protection NOTE: Depending on the conditions of use and the ambient temperature, the indication may differ slightly When the tool/battery is operated in a manner that from the actual capacity. causes it to draw an abnormally high current, the tool NOTE: The first (far left) indicator lamp will blink when automatically stops. In this situation, turn the tool off the battery protection system works. and stop the application that caused the tool to become overloaded. Then turn the tool on to restart. Adjusting depth of cut Overheat protection When the tool/battery is overheated, the tool stops CAUTION:... - Page 10 NEVER use the tool if it runs when you simply pull the switch trigger without press- ing the lock-off button. A switch in need of repair may result in unintentional operation and serious personal injury. Return tool to a Makita service center for proper repairs BEFORE further usage. CAUTION: The tool starts to brake the cir- cular saw blade rotation immediately after you release the switch trigger.
-
Page 11: Electric Brake
This tool is equipped with an electric blade brake. If the tool consistently fails to quickly stop the circular saw CAUTION: Use only the Makita offset wrench blade after switch lever release, have tool serviced at a to install or remove the circular saw blade. Makita service center. - Page 12 For tool with the ring WARNING: BE SURE TO TIGHTEN THE HEX BOLT COUNTERCLOCKWISE SECURELY. Also be careful not to tighten the bolt forcibly. Slipping your hand from the hex wrench can cause a per- sonal injury. WARNING: Make sure that the protrusion "a" on the inner flange that is positioned outside fits into the saw blade hole "a"...
- Page 13 Remove the side grip (handle) ► 1 . Rubber cap when operating bevel cutting. If you operate bevel cutting with the side grip (handle), it may touch Connect a Makita vacuum cleaner to your tool. the workpiece or your body and cause kickback or personal injury. CAUTION:...
-
Page 14: Operation
CAUTION: even after removing dust, have your tool serviced at a Always remove the battery when Makita service center. hanging the tool with the hook. CAUTION: Never hook the tool at high loca- CAUTION: Wear dust mask when performing tions or on the surfaces where the tool may lose cutting operation. - Page 15 WIRELESS ACTIVATION FUNCTION What you can do with the wireless activation function The wireless activation function enables clean and com- fortable operation. By connecting a supported vacuum cleaner to the tool, you can run the vacuum cleaner automatically along with the switch operation of the tool. ► 1 . Hook 2. Open position 3. Closed position To use the wireless activation function, prepare follow- ing items: Rip fence (Guide rule) •...
- Page 16 Tool registration for the vacuum cleaner NOTE: A Makita vacuum cleaner supporting the wireless activation function is required for the tool registration. NOTE: Finish installing the wireless unit to the tool ► 1 .
- Page 17 Press the wireless activation button on the vac- Connect the hose of the vacuum cleaner with the uum cleaner for 3 seconds until the wireless activation tool. lamp blinks in green. And then press the wireless acti- vation button on the tool in the same way. Set the stand-by switch on the vacuum cleaner to "AUTO". ► 1 . Wireless activation button 2. Wireless activation lamp If the vacuum cleaner and the tool are linked success- fully, the wireless activation lamps will light up in green...
- Page 18 NOTE: The wireless activation lamp on the tool will stop blinking in blue when there is no operation for 2 hours. In this case, set the stand-by switch on the vacuum cleaner to "AUTO" and push the wireless activation button on the tool again. NOTE: The vacuum cleaner starts/stops with a delay. There is a time lag when the vacuum cleaner detects a switch operation of the tool.
- Page 19 If the cancellation is performed successfully, the wire- Cancelling tool registration for the less activation lamps will light up in red for 2 seconds vacuum cleaner and start blinking in blue. NOTE: The wireless activation lamps finish blinking in Perform the following procedure when cancelling the red after 20 seconds elapsed. Press the wireless acti- tool registration for the vacuum cleaner.
- Page 20 Troubleshooting for wireless activation function Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the manual, do not attempt to dismantle the tool. Instead, ask Makita Authorized Service Centers, always using Makita replace- ment parts for repairs. State of abnormality Probable cause (malfunction) Remedy The wireless activation lamp does The wireless unit is not installed into the tool. Install the wireless unit correctly. not light/blink. The wireless unit is improperly installed into the tool. The terminal of the wireless unit and/or Gently wipe off dust and dirt on the terminal of the the slot is dirty.
-
Page 21: Maintenance
CAUTION: before attempting to perform inspection or These accessories or attachments maintenance. are recommended for use with your Makita tool specified in this manual. The use of any other CAUTION: Clean out the upper and lower accessories or attachments might present a risk of guards to ensure there is no accumulated saw- injury to persons. Only use accessory or attachment... - Page 24 Makita Europe N.V. Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 885852-224 www.makita.com 20201103...