Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Makita HS009GZ01
Summary of Contents for Makita HS009GZ01
- Page 1 INSTRUCTION MANUAL Cordless Circular Saw HS009G Read before use.
-
Page 2: Specifications
Only use the battery cartridges and chargers listed above. Use of any other battery cartridges and chargers may cause injury and/or fire. Symbols Intended use The followings show the symbols which may be used The tool is intended for performing lengthways and cross- for the equipment. Be sure that you understand their ways straight cuts and miter cuts with angles in wood while in firm contact with the workpiece. With appropriate Makita meaning before use. genuine saw blades, other materials can also be sawed. Read instruction manual. Noise Wear safety glasses. The typical A-weighted noise level determined accord- ing to EN62841-2-5: Sound pressure level (L... -
Page 3: Ec Declaration Of Conformity
Electrical safety Vibration Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any The vibration total value (tri-axial vector sum) deter- adapter plugs with earthed (grounded) power mined according to EN62841-2-5: tools. Unmodified plugs and matching outlets will Work mode: cutting wood reduce risk of electric shock. Vibration emission (a ) : 2.5 m/s or less... - Page 4 Do not let familiarity gained from frequent use When using the tool, do not wear cloth work of tools allow you to become complacent and gloves which may be entangled. The entangle- ment of cloth work gloves in the moving parts may ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.
- Page 5 Support large panels to minimise the risk of blade pinching and kickback. Large panels tend to sag under their own weight. Supports must be placed under the panel on both sides, near the line of cut and near the edge of the panel. Fig.1 Hold the power tool by insulated gripping surfaces, when performing an operation where...
- Page 6 Never force the saw. Push the saw forward at a speed so that the blade cuts without slowing. Forcing the saw can cause uneven cuts, loss of accuracy, and possible kickback. Lower guard function Check the lower guard for proper closing before each use. Do not operate the saw if the lower guard does not move freely and close instantly.
- Page 7 (1) Do not touch the terminals with any con- CAUTION: Only use genuine Makita batteries. ductive material. Use of non-genuine Makita batteries, or batteries that (2) Avoid storing battery cartridge in a con- have been altered, may result in the battery bursting causing fires, personal injury and damage. It will tainer with other metal objects such as also void the Makita warranty for the Makita tool and nails, coins, etc.
-
Page 8: Functional Description
CAUTION: Always install the battery cartridge 26. Do not insert any devices other than Makita fully until the red indicator cannot be seen. If not, wireless unit into the slot on the tool. it may accidentally fall out of the tool, causing injury to 27. - Page 9 NEVER use the tool if it runs when Let the tool and battery(ies) cool down. you simply pull the switch trigger without press- If no improvement can be found by restoring protection ing the lock-off button. A switch in need of repair system, then contact your local Makita Service Center. may result in unintentional operation and serious personal injury. Return tool to a Makita service center Indicating the remaining battery for proper repairs BEFORE further usage.
- Page 10 Positive stopper NOTICE: Do not pull the switch trigger hard without pressing in the lock-off button. This can The positive stopper is useful for setting the designated cause switch breakage. angle quickly. Turn the positive stopper so that the arrow on it points your desired bevel angle (around 22.5°/45°/60°). Loosen the lever and then tilt the tool CAUTION: The tool starts to brake the circular saw blade rotation immediately after you release the switch base until it stops.
- Page 11 This tool is equipped with an electric blade brake. If the base with your cutting line. For 45° bevel cuts, align the tool consistently fails to quickly stop the circular saw 45° position with it. blade after switch lever release, have tool serviced at a Makita service center. CAUTION: The blade brake system is not a substitute for blade guard. NEVER USE TOOL WITHOUT A FUNCTIONING BLADE GUARD.
- Page 12 6. Arrow on the tool tool. For tool with the ring CAUTION: Use only the Makita wrench to install or remove the circular saw blade. Loosen the lever on the depth guide and move the base down. Fig.18 ► 1 .
- Page 13 For tool with the inner flange for a Press the shaft lock fully so that the circular saw blade cannot revolve and use the hex wrench to tighten 15.88 mm hole-diameter saw blade the hex bolt. (country specific) Mount the inner flange with its recessed side facing outward onto the mounting shaft and then place circular saw blade (with the ring attached if needed), outer flange and hex bolt.
-
Page 14: Operation
Fig.26 example, use the tool for a light-duty cut for a while until ► 1 . Dust nozzle the battery cartridge warms up as high as room tem- perature. Then, the tool can work to its full capacity. OPERATION This tool is intended to cut wood products. With appro- priate Makita genuine circular saw blades, following materials can also be sawed: • Aluminum products • Mineral contained plastic Refer to our website or contact your local Makita dealer for the correct circular saw blades to be used for the material to be cut. - Page 15 Hold the tool firmly. The tool is provided with both a front Sub base (Guide rule) grip and rear handle. Use both to best grasp the tool. If both hands are holding saw, they cannot be cut by CAUTION: the circular saw blade. Set the base on the workpiece Make sure that the sub base (guide to be cut without the circular saw blade making any rule) is securely installed in the correct position contact.
- Page 16 Guide rail WIRELESS ACTIVATION FUNCTION Optional accessory CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed What you can do with the wireless before loosening the adjusting screws on the tool activation function base.
- Page 17 Tool registration for the vacuum cleaner NOTE: A Makita vacuum cleaner supporting the wireless activation function is required for the tool registration. NOTE: Finish installing the wireless unit to the tool before starting the tool registration.
- Page 18 Press the wireless activation button on the vac- Connect the hose of the vacuum cleaner with the uum cleaner for 3 seconds until the wireless activation tool. lamp blinks in green. And then press the wireless acti- vation button on the tool in the same way. Fig.40 Set the stand-by switch on the vacuum cleaner to "AUTO".
- Page 19 NOTE: The wireless activation lamp on the tool will stop blinking in blue when there is no operation for 2 hours. In this case, set the stand-by switch on the vacuum cleaner to "AUTO" and push the wireless activation button on the tool again. NOTE: The vacuum cleaner starts/stops with a delay. There is a time lag when the vacuum cleaner detects a switch operation of the tool.
- Page 20 If the cancellation is performed successfully, the wire- Cancelling tool registration for the less activation lamps will light up in red for 2 seconds vacuum cleaner and start blinking in blue. NOTE: The wireless activation lamps finish blinking in Perform the following procedure when cancelling the red after 20 seconds elapsed. Press the wireless acti- tool registration for the vacuum cleaner.
- Page 21 Troubleshooting for wireless activation function Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the manual, do not attempt to dismantle the tool. Instead, ask Makita Authorized Service Centers, always using Makita replace- ment parts for repairs. State of abnormality Probable cause (malfunction) Remedy Install the wireless unit correctly. The wireless activation lamp does The wireless unit is not installed into the tool. The wireless unit is improperly installed not light/blink. into the tool. Gently wipe off dust and dirt on the terminal of the The terminal of the wireless unit and/or the slot is dirty.
-
Page 22: Maintenance
Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Fig.46 ► 1 . Clamping screw 2. Positive stopper Make the base perpendicular or 45° to the circular saw blade using a triangular rule by turning the adjust- ing screw with a hex wrench. -
Page 23: Adjusting The Depth Guide
Make the base perpendicular, and set the depth of CAUTION: These accessories or attachments cut to the deepest. are recommended for use with your Makita tool specified in this manual. The use of any other Loosen the adjusting screws for the depth guide. The depth guide automatically adjusts its position. accessories or attachments might present a risk of injury to persons. Only use accessory or attachment... - Page 24 Jan-Baptist Vinkstraat 2, Makita Europe N.V. 3070 Kortenberg, Belgium 3-11-8, Sumiyoshi-cho, Makita Corporation Anjo, Aichi 446-8502 Japan 885933-224 www.makita.com 20210821...