Setting The Dip Switches; Control Pc Board - POWERPATH PS-8-LP Installation Instructions Manual

3.0 SETTING THE DIP SWITCHES

3.1 CONTROL PC BOARD

Refer to Figure 6 for the location and setting of the DIP switches on the Control PC board.
1. Set NAC output DIP Switch(s) on SW1 to follow corresponding input (IN1, IN2).
2. See Figure 7 for DIP switch locations and Table 3 for DIP Switch Selection and DIP Switch Settings
DIP Function
Switch Description
SW6
Any trouble conditions will
TROUBLE
clear automatically as the
Position 1 LATCH
trouble condition is
OFF / ON
repaired.
If IN1 Follower = ON, SBUS
will repeat the signals on
IN1 / CC1 input.
SBUS
Position 2
IN1 / IN2
If IN1 Follower = OFF,
SBUS will generate signals
according to its SW2 -
SYNC / TEMPORAL switch
setting.
NAC Output(s) or SBUS set
IN2 to trigger on IN2 / CC2 will
Position 3 FOLLOWER generate signals according
OFF / ON to its SYNC / TEMPORAL
switch setting.
Position 4 IN1 NAC Output(s) or SBUS set
P84905-002 A
TROUBLE LATCH OFF/ON
SBUS IN1/IN2
IN2 FOLLOWER OFF/ON
IN1 FOLLOWER OFF/ON
NAC4 SYNC/TEMPORAL
NAC3 SYNC/TEMPORAL
NAC2 SYNC/TEMPORAL
NAC1 SYNC/TEMPORAL
NAC4 IN1/IN2
NAC3 IN1/IN2
NAC2 IN1/IN2
NAC1 IN1/IN2
SYNC PROTOCOL
SYNC PROTOCOL
SBUS SYNC/TEMPORAL
SBUS MASTER/REMOTE
GF DETECT ON/OFF
AUX POWER CP/MP
NAC3-NAC4 CLASS A/B
NAC1-NAC2 CLASS A/B
Figure 7: Control PC Board DIP Switches
Table 3: Control PC Board DIP Switch Settings
Dip Switch Setting: Dip Switch Setting:
"LEFT"
Trouble indicators latch ON
until this switch is switched
to the disable (LEFT)
position or all power is
removed from the panel.
If IN2 Follower = ON,
SBUS will repeat the
signals on IN2 / CC2 input.
If IN2 Follower = OFF,
SBUS will generate signals
according to its SW2 - SYNC
/ TEMPORAL switch setting.
NAC Output(s) or SBUS set
to trigger on IN2 / CC2 turn
on when IN2 / CC2 is
"Active" and will apply NAC
reverse supervision voltage
when IN2 / CC2 is "Not
Active."
NAC Output(s) or SBUS set
firealarmresources.com
SW6
SW2
SW5
GROUND FAULT TEST
LOCATOR SWITCH
SW1
SW4
SW3
Dip Switch Setting:
"RIGHT" "LEFT"
Same Functionality as
Master Mode.
If IN1 Follower = ON, NAC
Output(s) set to trigger on
IN1 / CC1 will repeat the
signals on the SBUS when
IN1 / CC1 "Activates."
If IN1 Follower = OFF, NAC
Output(s) set to trigger on
IN1 / CC1 will repeat the
signals on the SBUS when
IN1 / CC1 "Activates."
See SW6 Position 2's
description for this setting.
See SW6 Position 2's
Dip Switch Setting:
"RIGHT"
Same Functionality as
Master Mode.
If IN1 Follower = ON, NAC
Output(s) set to trigger on
IN1 / CC1 will repeat the
signals on IN1 / CC1 input,
ignoring the NAC Output's
SYNC / TEMPORAL
dipswitch settings.
If IN1 Follower = OFF, NAC
Output(s) set to trigger on
IN1 / CC1 will repeat the
signals on the SBUS when
IN1 / CC1 "Activates."
See SW6 Position 2's
description for this setting.
See SW6 Position 2's
Sheet 15 of 37