Installation Requirements; Tools And Parts; Location Requirements - KitchenAid KVWB606HBS0 Installation Instructions & Use & Care Manual

Wall-mount canopy range hood
Table of Contents

Advertisement

Tools and Parts

Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools Needed
Level
Drill with 1¼" (3.0 cm), 3/8" (9.5 mm), and 5/16" (7.9 mm)
drill bits
Pencil
Wire stripper or utility knife
Tape measure or ruler
Pliers
Caulking gun and weatherproof caulking compound
Vent clamps
Jigsaw or keyhole saw
Flat-blade screwdriver
Metal snips
Phillips screwdriver
Parts Needed
Home power supply cable
1/2" (13 mm) UL listed or CSA approved strain relief
Three UL Listed wire connectors
For Vented Installations, You Will Also Need:
One wall or roof cap
Metal vent system
For Non-Vented (Recirculating) Installations, You Will
Also Need:
Recirculation Kit Part Number W10692908 for non-vented
(recirculating) installations only. See the "Assistance or
Service" section to order.
6" (15.2 cm) diameter round metal vent duct—length
required is determined by ceiling height.
Parts Supplied
Remove parts from packages. Check that all parts are included.
Hood canopy assembly with ventilator and LED and halogen
lights installed
Vent transition with back draft dampers installed
Metal grease filter(s)—depending on model and size
Vent cover support bracket
Mounting template
Two-piece vent cover
Four 4.2 x 8 screws
Six 5 x 45 mm mounting screws
Two D6.4 x 18 mm washers
Two 8 x 40 mm wall anchors
Four10 x 60 mm wall anchors
Four 5.4 x 75 mm screws (for 10 x 60 mm wall anchors)
Two 3.5 x 9.5 mm sheet metal screws
T10
TORX
adapter
®
®†
TORX and T10
are registered trademarks of Acument Intellectual Properties, LLC.
®
®

INSTALLATION REQUIREMENTS

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.
Have a qualified technician install the range hood. It is the
installer's responsibility to comply with installation clearances
specified on the model/serial/rating plate. The model/serial/
rating plate is located behind the left filter on the rear wall of the
vent hood.
Canopy hood location should be away from strong draft areas,
such as windows, doors and strong heating vents.
Cabinet opening dimensions that are shown must be used.
Given dimensions provide minimum clearance.
This range hood is recommended for use with cooktops with a
maximum total rating of 65,000 BTUs or less.
Grounded electrical outlet is required. See the "Electrical
Requirements" section.
The canopy hood is factory-set for venting through the roof
or wall. For non-vented (recirculating) installation see "For
nonvented (recirculating) installation only" in the "Connect Vent
System" section. Recirculation Kit Part Number W10692908 is
available from your dealer or an authorized parts distributor.
All openings in ceiling and wall where canopy hood will be
installed must be sealed.
For Mobile Home Installations
The installation of this range hood must conform to the
Manufactured Home Construction Safety Standards, Title 24
CFR, Part 328 (formerly the Federal Standard for Mobile Home
Construction and Safety, Title 24, HUD, Part 280) or when such
standard is not applicable, the standard for Manufactured Home
Installation 1982 (Manufactured Home Sites, Communities and
Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local
codes.
Product Dimensions
10¾" (27.3 cm)
13³⁄₁₆" (33.5 cm)
30" (76.2 cm)
36" (91.4 cm)
*For non-vented (recirculating) installations
**For vented installations
*28⁷⁄₈" (73.4 cm) min.
43³⁄₁₆" (109.7 cm) max.
24"
(60.8 cm)
**25¹⁄₄" (64.1 cm) min.
39¹¹⁄₃₂" (98.4 cm) max.
5"
(12.7 cm)
19¹¹⁄₁₆" (50.0 cm)
5

Advertisement

Table of Contents
loading

Table of Contents