Pyronix FPKX15DT2 Quick Start Manual

TS50131-2-2
2
EN50131-1
PD6662:2004
1: Disassembling the KX
KX15DT Security Grade 2
®
Environmental Class 2
TS50131-2-4
3
EN50131-1 15m Dual
PD6662:2004
Technology Digital
Security Grade 3
Environmental Class 2
Detector
EN50131-2-4:2008
TS50131-2-4 EN50131-1
2
EN50131-1
PD6662:2010
PD6662:2004
Security Grade 2
Security Grade 2
Environmental Class II
Environmental Class 2
RINS549-12
Installation of The KX15DD D The KX15DD Printed Circuit Board
®
of The KX15DD The KX15DD Printed Circuit Board ®
D
®
X15DD Casing ® Wall Bracket Fitting
4: Bracket Connections 5: Installation Hints
EOL Resistance
Wall Bracket Fitting Headers
C2 C3
EOL Resistance
Headers
CABLE ENTRY C3
a) Ceiling Do not partially or completely obscure the detector's
KNOCKOUT Pyro Sensor
+ – ALARM TAMPER LED
6K8 field of view with large objects such as furniture. 5K6
5K6 4K7
Bracket 4K7
Pyro Sensor 2K2
2k2 1K
1K
Fitting
Avoiding False Alarms
The KX15DD sensitivity is selected by
Alarm LED
the two headers located at the bottom
of the PCB
Alarm LED 1. Avoid placing the detector in direct sunlight.
The sensitivity can be either AUTO,
LOW AUTO AUTO HI HIGH or LOW.
2. Do not let pets and other animals wander freely
OFF ON (Default)
To select either of these sensivities
whilst the alarm system is armed.
please see the diagrams below.
Auto Sensitivity
OFF ON (Default)
Auto Sensitivity
ll Mounting Ceiling Bracket Fitting
3. Do not mount the detector near heaters or
Ceiling Bracket Fitting C5
radiators.
C5
LOW AUTO
4. Do not mount the detector near open windows or
+ – ALARM TAMPER LED
6K8 5K6
5K6 4K7
LOW AUTO AUTO HI 4K7 2K2
2k2 1K
1K air vents as draughts may cause false alarms
5. Mount the detector on a stable surface.
b) Wall Bracket
This is the default
Fitting setting
This is the default 6. Do not run cable parallel to mains wiring.
LOW AUTO AUTO HI
setting
The Wiring Connections For The KX15DD (Examples using 4k7 for alarm, 4k7 for tamper)
iring Connections For The KX15DD (Examples using 4k7 for alarm, 4k7 for tamper)
®
ormally Closed Wiring
10: Choose the Connection Type: Single End of Line Wiring (SEOL)
ing Control Panel Single End of Line Wiring (SEOL) E2 Control Panel Double End of Line Wiring (DEOL)
E2 a) Normally Closed b) Single End of Line Wiring E3
Control Panel
+AUX- Z1 T T 5K6 6K8 +AUX- Z1 T T
5K6
4K7
5K6 6K8 +AUX- Z1 T T 4K7 5K6
2K2
4K7 5K6 2K2 4K7
1K
ALARM CONTROL PANEL ALARM CONTROL PANEL 4K7 1K
ALARM CONTROL PANEL The
2K2 2K2
2K2
1K 1K
1K
connection
shows the
+ - + -
+ – ALARM TAMPER LED + - + – ALARM TAMPER LED
8 5K6 6K8 5K6
6 5K6
4K7 example value 4K7
7 4K7
2K2 2K2
6 2 1K 6K8 + – ALARM TAMPER LED 5K6 2K2
1K
K 5K6 1K 4k7 for tamper
7 4K7
2 4K7 2K2
2K2
1K
1K (EOL).
® ®
KX15DD KX15DD
®
KX15DD
Zone Doubling Example (Matrix 424,832 or 832+)
ing Example (Matrix 424,832 or 832+)
Control Panel
6K8
E5
5K6
Control Panel 5K6
6K8 4K7 4K7
+ -
+ - + - +AUX- Z1 T T
K8 5K6 ALM ALM TAMPER
5K6 ALM ALM 2K2 TAMPER
2K2 ALM ALM TAMPER
5K6
K6 4K7
4K7 1K
+AUX- Z1 T T 1K
4K7
K7
2K2 2K2
Link 5K6
2K2
K2 1K
1K
4K7
1K 1K
2K2
1K
+AUX-
+AUX-
+AUX-
+ – ALARM TAMPER LED
+ – ALARM TAMPER LED 5K6
6K8 5K6 6K8
5K6 4K7 5K6 4K7
4K7 4K7 2K2
2K2 TAMPER
ED TAMPER + TAMPER – ALARM TAMPER LED 5K6
5K6 2K2 6K8 KX15DD ® 2K2 1K
1K
1K 5K6 4K7 1K
4K7
4K7
2K2 2K2
® 2K2 1K KX
1K KX15DD KX
ALARM 1K ALARM KX
ALARM
11: Powering Up 12: The 15m Volumetric Lens
When the detector is first powered up, it will run
through a self-test routine, indicated by the flashing
LEDs. Once this has distinguished the detector is
ready to use.

 READY
NOT READY
ALARM CONTROL PANEL
ALARM CONTROL PANEL ALARM CONTROL PANEL
+ -
+ - + -
Link
Link Link
2K2 2K2
+ - + - + - 2K2
+ - + -
+ -
Hard Wired Hard Wired
Hard Wired
Resistor
Resistor Resistor
+ - + -
+ - + -
+ - ALM ALM TAMPER + - ALM ALM
ALM ALM TAMPER ALM ALM
ALM ALM TAMPER ALM ALM TAMPER
* In an EN50131-1 system the maximum
detection is 13m.
a) Printed Circuit Board
b) Lens Illuminator
e) PCB
Screw
f ) Back
Tamper
f ) Nut
d) Lens Holder
®
c) Lens E EOL Resistor Headers
E EOL Resistor Headers
6: Sensitivity Settings
SENSITIVITY SETTINGS:
®
The KX15DD has two sets of header pins on the PCB, one on
ALARM CONTROL PANEL
either side of the connector blocks. These headers are used to
SENSITIVITY SETTINGS:
®
Auto, High or Low. The KX15DD has two sets of header pins on the PCB, one on
select the End Of Line resistance for EOL wiring applications.
a) Auto Sensitivity (Default)
6K8 + – ALARM TAMPER LED either side of the connector blocks. These headers are used to
5K6 If EOL wiring is not used, leave the headers OFF.
5K6 4K7
4K7 Auto, High or Low. 2K2
select the End Of Line resistance for EOL wiring applications.
2k2 1K
1K See the diagams below
+ - If EOL wiring is not used, leave the headers OFF.
The set to the left of the + terminal selects the value of the
See the diagams below resistance across the ALARM relay. The set to the right of the
The set to the left of the + terminal selects the value of the
The KX15DD sensitivity is selected by TAMPER terminals selects the value of the End Of Line resistor.
resistance across the ALARM relay. The set to the right of the
the two headers located at the bottom
TAMPER terminals selects the value of the End Of Line resistor.
of the PCB If the resistance value you require
is not selectable, leave the
If the resistance value you require
The sensitivity can be either AUTO, headers off and wire a resistor
is not selectable, leave the This symbol illustrates
LOW AUTO AUTO HI HIGH or LOW. of the required value between the
headers off and wire a resistor
appropriate terminals as shown. where the resistors are
To select either of these sensivities of the required value between the
connected internally
please see the diagrams below. appropriate terminals as shown.
High Sensitivity
+ -
High Sensitivity Low Sensitivity
ALM ALM TAMPER
6K8 + – ALARM TAMPER LED 5K6
6K8 + – ALARM TAMPER LED 5K6
5K6 4K7 5K6 4K7
AUTO HI 4K7 2K2 LOW AUTO AUTO HI 4K7
2k2 1K 2K2
1K 2k2 1K
1K
6K8 + – ALARM TAMPER LED 5K6
5K6
4K7
LOW AUTO AUTO HI 4K7 2K2 LOW AUTO AUTO HI
2k2 1K
1K
TAMPER
KX
LOW AUTO AUTO HI
ALARM LOW AUTO AUTO HI
LOW AUTO AUTO HI
®
Double End of Line Wiring (DEOL)
E3 Control Panel Remote LED Enable ®
The KX15DD has a terminal marked 'LED' which can be used
to enable the LED in walk test only on a alarm control panel.
c) Double End of Line Wiring ®
Control Panel
The KX15DD has a terminal marked 'LED' which can be used
6K8
5K6 5K6
+AUX- Z1 T T to enable the LED in walk test only on a alarm control panel.
This is used when the LED is disabled via the LED ON/OFF link.
5K6
4K7 4K7
6K8 4K7 5K6
2K2 +AUX- Z1 T T 2K2
This is used when the LED is disabled via the LED ON/OFF link.
5K6 2K2 The To enable this feature, the LED terminal needs to be connected
4K7
1K 1K
4K7 ALARM CONTROL PANEL ALARM CONTROL PANEL 1K ALARM CONTROL PANEL ALARM CONTROL PANEL ALARM CONTROL PANEL to an Output at the alarm control panel. When the system is
ALARM CONTROL PANEL ALARM CONTROL PANEL
2K2 connection
2K2 To enable this feature, the LED terminal needs to be connected
is in walk test mode the Output should be at 0V.
1K
1K to an Output at the alarm control panel. When the system is
shows the
is in walk test mode the Output should be at 0V.
The Output would be usually programmed as "Remote LED
example
+ - + - + - enable". + - + -
+ - + – ALARM TAMPER LED + -
6K8 5K6
The Output would be usually programmed as "Remote LED
5K6
4K7
4K7 values of 4k7
enable". 2K2
+ – ALARM TAMPER LED
6K8 2K2 5K6 1K
5K6 1K
4K7 for Alarm and
+ – ALARM
4K7 2K2
2K2
1K
1K
4K7 for tamper
+ – ALARM TAMPER LED
®
KX15DD
(EOL).
®
KX15DD Link
Two DEOL Detectors To One Input
2K2
+ -
+ -
Two DEOL Detectors To One Input
E5
Hard Wired
Control Panel
6K8
5K6 Resistor
Control Panel 5K6
4K7
6K8
+ - + - 5K6 + - +AUX- Z1 + - T T 4K7
+ - + - + - + -
ALM ALM ALM TAMPER ALM TAMPER 2K2 ALM ALM ALM
ALM ALM TAMPER 6K8 5K6 ALM
ALM ALM TAMPER ALM 2K2
4K7
5K6 +AUX- Z1 T T 4K7 1K
2K2
6K8 Link
4K7 2K2
5K6 1K
2K2 1K
Link
4K7
1K
2K2
1K
+AUX-
+AUX-
+AUX-
+ – ALARM TAMPER LED
6K8 5K6 6K8
5K6
5K6 4K7
4K7
4K7 2K2
TAMPER TAMPER + – ALARM TAMPER LED + TAMPER – ALARM TAMPER LED TAMPER
TAMPER TAMPER 6K8 5K6 2K2 6K8 TAMPER TAMPER 5K6 2K2
1K KX15DD ®
5K6 1K
5K6 4K7 1K 4K7
4K7 4K7 2K2
2K2
2K2 2K2
KX 1K KX ® 1K
KX KX15DD 1K
ALARM ALARM ALARM 1K KX ALARM ALARM ALARM
ALARM ALARM
13: Dimensions and Weight
85°
60 zones
7 planes
RLNS074
ALARM CONTROL PANEL
ALARM CONTROL PANEL ALARM CONTROL PANEL
+ -
+ - + -
117 x 69 x 50mm
Link
Link Link
+ - + -
+ -
125g (4.4 oz)
+ -
+ -
TAMPER + - ALM ALM TAMPER
TAMPER ALM ALM TAMPER
ALM ALM TAMPER
without bracket
2: The Printed Circuit Board
b) Mains Frequency
50Hz
(Default)
60Hz
c) Sensitivity Auto/High
See Section 6
d) AND/OR
See section 7
e) ALARM LED
LED Disable
f ) Tamper and Alarm
LED Enable Resistor Headers
g) Casing Screw
(Default)
ALARM CONTROL PANEL ALARM CONTROL PANEL
b) High Sensitivity
+ - + -
This symbol illustrates
where the resistors are
connected internally
Low Sensitivity
+ - + -
ALM ALM TAMPER ALM
6K8 + – ALARM TAMPER LED 5K6
5K6 4K7
4K7
LOW AUTO AUTO HI 2K2
2k2 1K
1K
6K8 + – ALARM TAMPER LED 5K6
5K6
4K7
4K7 2K2
2k2 1K
1K
TAMPER TAMPER
KX
ALARM LOW AUTO AUTO HI ALARM
LOW AUTO AUTO HI
Remote LED Enable
d) Two Double End of Line Detectors to One Input
ALARM CONTROL PANEL
The connection shows the
example values 4k7 for alarm,
+ -
4k7 for tamper (EOL).
TAMPER LED
Control Panel
Output
Control Panel
(0v in Walk Test)
Output
Link
(0v in Walk Test)
+ -
+ -
TAMPER ALM TAMPER ALM ALM TAMPER
ALM TAMPER 5K6
ALM TAMPER
1K 4K7
5K6
2K2
4K7
1K
2K2
1K
+AUX-
+ – ALARM TAMPER LED
5K6
4K7
2K2
TAMPER
1K
KX KX
KX KX
KX ALARM
RINS1038-3
RINS1038-3 14: Technical Specification
Model: KX15DT
85°
60 zones
Colour: White
7 planes
RLNS074
LED Colours: Orange (Microwave), Blue (Alarm),
Green (PIR)
Casing: 3mm ABS, 0.4mm HDPE in Lens Area
Detection Method: Low noise dual element
pyroelectric sensor and Microwave Doppler Sensor
PIR Sensitivity: Auto or High
Temperature Comp: Digital
+ -
+ -
+ -
Detection Range: 15m (13m according to EN
50131-2-4)
+ -
+ -
+ - ALM Detection Speed: 0.3 - 3.0m/s ALM TAMPER
ALM ALM TAMPER
ALM ALM TAMPER
Operating Voltage: 9-16V DC 13.8V DC typical
3: Cable Entry + Mounting
a) Terminals b) Cable Entry
a) Mounting Screw
Knockouts
h) Microwave
Potentiometer
g) Piro Sensor
DO NOT TOUCH
c) Case Lid Screw
Fitting
7: AND/OR Mode 8: Microwave Potentiometer
+ -
Note: turning pot fully anti-clockwise turns off
microwave
+ -
AND
Conventional Dual Tech (Both technologies need to
be triggered simultaneously to generate an alarm)
ALM TAMPER
ALARM
OR
KX
If either single technology detects prolonged
intruder activity an alarm will be generated
e) Zone Doubling Example (For Matrix 424, 832, 832+)
The connection shows the
example values 4k7 for alarm,
4k7 for tamper (EOL). And 2K2
for the zone doubling EOL.
+ -
+ -
ALM ALM TAMPER
TAMPER
KX
ALARM
15: Compliance and Warranty
Current Consumption: 24mA @ 12V (Min), 30mA @
12V (Max)
Relay Output: 50mA 60 VDC, 42 VAC (RMS)
This product is approved for use in
the Residential, Commercial and Light
Contact Resistance: <10ohms
Industrial Environment. It complies
with EN50131-2-4:2008 at security
Mounting Height: 1.8m - 2.4m
grade 2, environmental class 2. UK =
Suitable for use with systems installed
Tamper Switch: 12V 50mA
to PD6662:2010. EXPORT = Suitable for
Storage Temp: -40°C to 80°C
use with systems installed to EN50131-
1:2006+A1:2009
Certified operating temperature: -10°C to 40°C
WARRANTY: This product is sold subject to our
Nominal working temperature: -30°C to 70°C
standard warranty conditions and is warranted
against defects in workmanship for a period of five
Accessories: Wall and Ceiling brackets
years. In the interest of continuing improvements
Emissions: EN55022 Class B of quality, customer care and design, Pyronix ltd
reserves the right to amend specifications without
Immunity: EN50130-4
giving prior notice.
+ -
ALM ALM TAMPER
Knockout
TAMPER
KX
ALARM
ALARM CONTROL PANEL
+ -
9: EOL Resistor Headers
Link
ALARM CONTROL PANEL 2K2 ALARM CONTROL PAN
+ -
The KX15DT has 2 set of header pins at the top of
Hard Wired
the printed circuit board. These headers are used Resistor
+ -
to select the End of Line resistance for EOL wiring
+ -
ALM ALM TAMPER ALM ALM TAMPER
applications.
If EOL wiring is not used, leave the headers OFF.
+ - + -
TAMPER ALM ALM TAMPER TAMPER
KX
ALARM
Minimum
Range (0m)
TAMPER
Maximum
KX
ALARM ALARM
Range (15m)
ALARM CONTROL PANEL
+ -
Link
2K2
+ - + -
Hard Wired
Resistor
+ - + -
ALM ALM TAMPER ALM ALM TAMPER
TAMPER TAMPER
KX KX
ALARM ALARM
16: Contact Information
Secure Holdings, Pyronix Ltd,
Braithwell Way, Hellaby,
Rotherham, South Yorkshire
S66 8QY
Customer Support:
+44(0)845 6434 999 (local rate)
or +44(0)1709 535225
Hours: Mon to Fri, 8:00am till 6:30pm
Email: customer.support@pyronix.com
Website: www.pyronix.com
For electrical products sold within the
European Community. At the end of the
electrical products useful life, it should
not be disposed of with household
waste. Please recycle where facilities
exist. Check with your Local Authority
or retailer for recycling advice in your
country.
+ -
ALM
TAMPER
ALARM
+ -
ALM ALM TAMPE
KX
TAMPER
K