Additional Features; Using - Bosch TDA3605GB Operating Instructions

Using Your Iron
1. Your iron
N. Auto shut off
indicator lamp (*)
A. Shot of steam
B. Spray button
C. Steam regulator
D. Steam regulator
pointer
E. Spray
outlet
I. Temperature control
H. Temperature control pointer
F. Water tank
G. Soleplate
2. Filling the water tank
Set the steam regulator (C) to the «0» position and
unplug the iron from the mains!
Use only clean water from the tap and do not mix anything with
it. The addition of other liquids, such as perfume, will damage
the appliance.
Do not use condensation water from tumble dryers, air conditioners
or similar appliances. This appliance has been designed to use
normal tap water.
To prolong the optimum steam function it is possible to mix tap
water with distilled water 1:1. If the tap water in your district is
very hard, mix tap water with distilled water 1:2.
You can inquire about the water hardness with your local water
supplier
To prevent spillage of water out of the appliance in vertical position,
never fill beyond the «max» water level mark!
7. Ironing without steam
This function enables the iron to be used for dry ironing.
1. Set the steam regulator (C) to the «0» position.
2. Select an appropriate temperature for the type of material being
ironed.
8. Spray
This can be used to remove stubborn wrinkles.
1. Do not use the spray function with silk as staining may occur.
2. Make sure that there is water in the tank (F).
3. When ironing, press the spray button (B) and water will spray
out of the spray outlet (E) onto the garment.
9. After finishing each ironing session
1. Unplug the iron from the mains socket.
2. Set the steam regulator (C) to the «0» position.
3. Open the water tank cover (L).
4. Hold the iron with the point facing up and shake it gently until
all the water has come out.
5. Set the iron aside in a vertical position to cool down.
6. Coil the power cable (M) loosely around the heel of the iron,
before storing.
7. Store the iron in an upright position.
10. Multiple de-scaling system
This range of irons is equipped with the following de-scaling
features "AntiCalc".
A. self-clean
Each time you use the steam regulator (C), the "self-clean" system
cleans the mechanism of any scale deposits.
B. calc'n clean
The "calc'n clean" function helps to remove scale particles out
of the steam chamber. Use this function approximately every 2
weeks, if the water in your area is very hard.
Fill the water tank, set the temperature dial (I) to the "max". position
and plug in the iron.
After the necessary warm-up period, unplug the iron and hold
it over a sink. Take out the steam regulator (C) by turning it to
the position while pressing it down. Gently shake the iron.
Boiling water and steam will come out, carrying scale or deposits
that might be there. When the iron stops dripping, reassemble
the steam regulator in reverse order and move it to the «0»
position. Heat up the iron again until the remaining water has
evaporated.
3. Setting the temperature
The temperature control (I) adjusts the temperature of the
soleplate (G).
1. Check the temperature instructions shown on the care label
M.Power
cable
of the garment you are ironing and set the temperature
control (I) to the corresponding position by lining it up with
the pointer (H) on the iron:
L. Water tank
cover
Fabric
Synthetics
K. Pilot lamp
Silk - Wool
Cotton - Linen
J. Max. Water
* Model dependent
2. If you are unsure what type of material the garment is made from,
start ironing on the lowest temperature setting and increase
accordingly. If the garment is made from mixed fabrics, set the
temperature for the most delicate material.
3. For silk, woollen or synthetic materials iron the reverse side
of the fabric to prevent shiny patches. Avoid using the spray
function to prevent stains.
4. Sort your garments based on their care labels, always
starting with clothes that have to be ironed at the lowest
temperature.
5. The pilot lamp (K) will stay lit while the iron is heating up and go
out once the selected temperature has been reached. Wait a
few seconds after the lamp goes out before you start ironing.
Once the iron is ready, you can continue to iron even if the pilot
lamp comes on again.
6. If your iron has auto shut-off and the lamp on the top of the
handle (N) is flashing, the auto shut-off has activated. Gently
move the iron side to side to restart it.
If the steam regulator needle is soiled, remove any deposits from
the needle tip with vinegar and rinse off with clean water.
C. anti-calc cartridge (model dependent)
The anti-calc cartridge has been designed to reduce the build-up
of scale produced during steam ironing, helping to extend the
useful life of your iron. Nevertheless, the "anti-calc" cartridge cannot
remove all of the scale that is produced naturally over time.
11. Anti-drip system
All the irons in this range are equipped with an anti-drip system.
This will automatically stop the iron producing steam when the
selected temperature setting is too low to prevent water from
dripping out of the soleplate. You may hear a clicking sound when
this system is in operation.
Additional Features (Model Dependent)
Auto shut-off
Some irons in this range are equipped with an auto-shut off
system.
The "secure" auto shut-off function switches off the iron
automatically when it is not being used, thus helping to prevent
accidents and saving energy. When the appliance is first plugged
in, this function will be inactive for the first 2 minutes to allow it to
reach the set temperature.
If during ironing, the iron is not moved for a certain length of time,
the iron will automatically switch off. The length of time will depend
on the position the iron has been left in:
Horizontally (flat) or on its side:
Vertically (upright):
The pilot light on the top of the handle (N) will flash when auto
shut-off has been activated. To switch the iron back on, move it
gently from side to side. The light will stop flashing.
4. Ironing with steam
The steam regulator (C) is used to adjust the amount of
steam produced when ironing.
1. Make sure that there is water in the tank (F).
2. Adjust the temperature setting and then set the steam regulator,
by lining it up with the pointer (D), according to the table below.
Steam will automatically be produced:
Temperature Setting
Temperature Setting
•
••
3. You can get extra steam by pressing and holding the steam
regulator (C) for a maximum of 2 seconds.
•••
Note: At a temperature setting of "•", the soleplate is not hot enough
to produce steam so the steam regulator should be set to the «0»
position to avoid water dripping from the soleplate (G).
5. Ironing with shot of steam
This can be used to remove stubborn wrinkles or to press
in a sharp crease or pleat. It cannot be used on a synthetic
setting for delicate items.
1. Set the temperature control (I) to the "•••" or "max" position.
2. Set the steam regulator (C) to the «2» position.
3. Press the shot of steam (A) button on the handle repeatedly at
intervals of 5 seconds.
6. Vertical steaming with shot of steam
This can be used to remove creases from hanging clothes,
curtains etc. It cannot be used on a synthetic setting for
delicate items.
WARNING! Do not use vertical steam while the item is being
worn. Never spray or aim steam at people or animals!
1. Make sure that there is water in the tank (F).
2. Set the temperature control (I) to the «•••» or «max» position
and the steam regulator (C) to the «2» position.
3. Hold the iron in an upright position about 15 cm away from the
garment being steamed.
4. Press the shot of steam button (A) on the handle at intervals of
5 seconds, however, after 4 jets of steam, wait for 10seconds
to allow for continued steam production.
Fabric-protection soleplate cover
The fabric-protection cover is used for steam-ironing delicate
garments at maximum temperature without damaging them.
Use of the protector also does away with the need for a cloth to
prevent shine on dark materials.
It is advisable to first iron a small section on the inside of the
garment to see if it is suitable.
To attach the fabric protector to the iron, place the tip of the iron
into the tip of the fabric protector and press the rear of the protector
upward until you hear a click. To release the fabric protector, pull
down on the clip at the rear and remove from the iron.
The protective cover can be purchased from After-sales.
Tips to help you save energy
Steam production consumes the most energy. To help minimise
the energy used, follow the advice below:
• Start by ironing the fabrics that require the lowest ironing
temperature.
• Regulate the steam according to the selected ironing
temperature.
• Only use steam if necessary. If possible, use the spray
function instead.
• Try to Iron the fabrics while they are still damp and reduce the
steam setting. Steam will be generated from the fabrics rather
than the iron. If you tumble dry your fabrics before ironing
them, set the tumble drier to the 'iron dry' programme.
30 seconds
8 minutes • If the fabrics are damp enough, turn off the steam regulator
completely.
• Stand the iron upright during pauses. Resting it horizontally
with the steam regulator on generates wasted steam.
Steam Regulator Setting
••• to "max" 2
•• 1
Accessory code
(After-sales)
650808