Table of Contents

Advertisement

Available languages

Available languages

Quick Links

RF Programmable Features :
Feature Selection
First
Second
Third
Fourth
Fifth
Sixth
Seventh
Eighth
Note : When both Passive Arming and Voltage Sensing are selected, you must hardwire the driver's door pin switch in order to begin
the passive arming sequence.
To program these selectable features;
Action
Turn ignition on
Flip valet switch on then off 3 times
Within 3 seconds, turn ignition Off
First
Then On
Press transmitter button 1 to change
Second
Flip valet switch on then off
Press transmitter button 1 to change
Third
Flip valet switch on then off
Press transmitter button 1 to change
Fourth
Flip valet switch on then off
Press transmitter button 1 to change
Fifth
Flip valet switch on then off
Press transmitter button 1 to change
Sixth
Flip valet switch on then off
Press transmitter button 1 to change
Seventh
Flip valet switch on then off
Press transmitter button 1 to change
Eighth
Flip valet switch on then off
Press transmitter button 1 to change
Flip valet switch on then off
Turn the ignition switch off
Note : Once you enter the feature programming mode, do not allow more than 15 seconds to pass between steps, or the programming
will be terminated.
PROGRAMMABLE FEATURES
1 Chirp
1 Second Door Locks
Auto Lock On
Auto Unlock On
Passive Door Locks
Passive Arming
Voltage Sense On
Hi-Jack Start Timer 15 Sec.
Hi-Jack Feature On
or
or
or
or
or
or
or
or
or
2 Chirps
3.5 Second Door Locks
Auto Lock Off
Auto Unlock Off
Active Door Locks
Active Arming
Voltage Sense Off
Hi-Jack Start Timer 45 Sec
Hi-Jack Feature Off
System Response
No response
1 Chirp - LED 1 flash
Short chirp, then long chirp
1 chirp = 1 second door locks
2 chirps = 3.5 second door locks
2 chirps = auto locks off
1 chirp = auto locks on
2 chirps = auto unlock off
1 chirp = auto unlock on
2 chirp = active locks
1 chirps = passive locks
1 chirp = passive arming
2 chirps = active arming
2 chirps = voltage sense feature off
2 chirp = voltage sense feature on
2 chirp = Hi-jack start timer 45 seconds
1 chirps = Hi-jack start timer 15 seconds
1 chirp = Hi-jack feature on
2 chirps = Hi-jack feature off
Exit Program Mode
Exit Program Mode
Page 1
Model APS-25HJ
Installation Manual
Default
1 Second
Auto Lock Off
Auto Unlock Off
Active Locks
Passive Arming
Voltage Sense Off
Start Timer 45 Sec.
Hi-Jack Feature On

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the APS-25HJ and is the answer not in the manual?

Questions and answers

Summary of Contents for Prestige APS-25HJ

  • Page 1 Model APS-25HJ Installation Manual PROGRAMMABLE FEATURES RF Programmable Features : Feature Selection 1 Chirp 2 Chirps Default First 1 Second Door Locks 3.5 Second Door Locks 1 Second Second Auto Lock On Auto Lock Off Auto Lock Off Third Auto Unlock On...
  • Page 2 INSTALLATION OF MAJOR COMPONENTS Control Module : Select a mounting location inside the passenger compartment ( up behind the dash ), and secure using the two screws provided. The control module can also be secured in place using cable ties. Do not mount the control module in the engine compartment, as it is not waterproof.
  • Page 3: Shock Sensor

    Shock Sensor : Select a solid mounting surface for the shock sensor on the firewall inside the passenger compartment, and mount the sensor using the two screws provided. The shock sensor can also be secured to any fixed brace behind the dash using tie straps. Whichever mounting method is selected, make certain that the sensitivity adjustment is accessible for use later in the installation.
  • Page 4 Black Wire : CHASSIS GROUND Connect this wire to a solid, metal part of the vehicle’s chassis. Do not confuse this wire with the thin black antenna wire that exits the control module independently. Orange Wire: 300 mA GROUND OUTPUT WHEN ARMED - N. C. STARTER DISABLE (Optional Relay Required) This wire is provided to control the starter cut relay.
  • Page 5: Completing The Installation

    2 Pin Red Connector : HI-JACK OVERRIDE Route the 2 pin red connector from the override switch previously mounted to the mating two pin connector on the module. Red & Green 2 Pin White Connector : DOOR LOCK OUTPUTS These wires will provide a pulsed ground output to the factory door lock control relay. The maximum current draw through these outputs must not exceed 300 mA.
  • Page 6 Optional Relay Required Audiovox Corp., 150 Marcus Blvd., Hauppauge, N.Y. 11788 128-5265A Page 6...
  • Page 7 Modelo APS-25HJ Manual de instalación FUNCIONES PROGRAMABLES Funciones RF programables: Selección de función 1 chirrido 2 chirridos Valor por defecto Trabado de puertas de 1 Trabado de puertas de 3,5 1 segundo Primera segundo segundos Trabado automático “on” Trabado automático “off”...
  • Page 8 INSTALACIÓN DE LOS COMPONENTES PRINCIPALES Módulo de control: Elija un lugar de montaje adentro del compartimiento del pasajero (arriba y detrás del tablero de instrumentos) y fije con los dos tornillos provistos. No instale el módulo en el compartimiento del motor dado que no es impermeable. Se debe evitar colocar la unidad directamente encima de componentes electrónicos instalados en fábrica.
  • Page 9: Cableado Del Sistema

    CABLEADO DEL SISTEMA Conexiones de cableado del arnés de alimentación principal: Cable rojo con fusible: FUENTE CONSTANTE DE BATERÍA DE +12 VCC Este cable alimenta el módulo de control y controla la sensibilidad del circuito de detección de voltaje que detecta el encendido o apagado de una luz interior cuando se abre una puerta.
  • Page 10 Cable anaranjado: SALIDA DE CONEXIÓN A TIERRA DE 300 mA CUANDO ESTÁ ACTIVADO - DESACTIVACIÓN DEL ARRANCADOR (Se requiere un relé opcional) Este cable controla el relé de bloqueo del arrancador. Conecte el cable anaranjado al terminal 86 del relé. Conecte el terminal 85 del relé...
  • Page 11: Finalización De La Instalación

    Trabas de puertas con conmutación a tierra de 3 cables En esta aplicación, el cable rojo proporciona un impulso a tierra durante la secuencia de activación o una salida a tierra con impulsos. Conecte el cable rojo al cable de señal a tierra de poca corriente del interruptor para trabar las puertas que viene instalado de fábrica al relé...
  • Page 12 SALIDAS PARA para su funcionamiento TRABAR PUERTAS ROJO (-) Impulso de trabado Rojo (-)Impulso de destrabado Negro VERDE Azul APS-25HJ Cable de alimentación de Rojo la bobina de encendido Negro existente Gris Interruptor valet A la bobina Luces de Luces de...

Table of Contents