Table of Contents
Advertisement
1. Loosen screw, until the guard lug
groove
20
on the gear case hub.
2. Rotate guard
into desired working position. The guard
8
body should be positioned between the spindle and the
operator toprovide maximum operator protection.
3. Tighten the screw to secure the guard on the gear case
cover. (Fasten torque no less than 2.5 N-M). You should be
unable to rotate the guard by hand. Do not operate grinder
with a loose guard.
4. To remove the guard, loosen screw and pull up on the
guard.
CAUTION: Failure to properly seat the wheel before
turning the tool on may result in damage to the tool or
the wheel.
Flanges and Wheels
Mounting Non-Hubbed Wheels (Fig. E)
WARNING: Failure to properly seat the flanges and/or
wheel could result in serious injury (or damage to the tool
or wheel).
CAUTION: Included flanges must be used with depressed
centre Type 27 and Type 42 grinding wheels and
Type 41 cutting wheels. See the Accessories Chart for
more information.
WARNING: A closed, two-sided cutting wheel guard is
re quired when using cutting wheels.
WARNING: Use of a damaged flange or guard or fail ure
to use proper flange and guard can re sult in injury due to
wheel breakage and wheel contact. See the Accessories
Chart for more information.
1. Place the tool on a table, guard up.
2. Install the backing flange
centre (pilot) facing the wheel. Press the backing flange
into place.
3. Place wheel
19
against the backing flange, centreing the
wheel on the raised centre (pilot) of the backing flange.
4. While depressing the spindle lock button and with the hex
depressions facing away from the wheel, thread the locking
flange
7
on spindle so that the lugs engage the two slots
in the spindle.
5. While depressing the spindle lock button, tighten the
locking flange
by hand or using the wrench supplied.
7
(Only use a locking flange if it is in perfect condition.) Refer
to Accessory Chart to see flange details.
6. To remove the wheel, reverse the above procedure.
Mounting Sanding Backing Pads (Fig. F)
nOTE: Use of a guard with sanding discs that use backing pads,
often called fiber resin discs, is not required. Since a guard is
not required for these accessories, the guard may or may not fit
correctly if used.
WARNING: Failure to properly seat the flange/ clamp nut/
wheel could result in serious injury (or damage to the tool
or wheel).
19
can rotate freely in the
6
on spindle
4
with the raised
WARNING: Proper guard must be reinstalled for grinding
wheel, cutting wheel, sanding flap disc, wire brush or
wire wheel applications after sanding applications
are complete.
1. Place or appropriately thread backing pad
the spindle.
2. Place the sanding disc
17
3. While depressing spindle lock
on the spindle, piloting the raised hub on the clamp nut into
the centre of san ding disc and backing pad.
4. Tighten the clamp nut by hand. Then depress the spindle
lock button while turning the sanding disc until the sanding
disc and clamp nut are snug.
5. To remove the wheel, grasp and turn the backing pad and
sanding pad while depressing the spindle lock button.
Mounting and Removing Hubbed Wheels
(Fig. A)
Hubbed wheels install directly on the threaded spindle. Thread
of accessory must match thread of spindle.
1. Remove backing flange by pulling away from tool.
2. Thread the wheel on the spindle
3. Depress the spindle lock button
tighten the hub of the wheel.
4. To remove the wheel, reverse the above procedure.
NOTICE: Failure to properly seat the wheel before turning
the tool on may result in damage to the tool or the wheel.
Mounting Wire Cup Brushes and
Wire Wheels (Fig. A)
WARNING: Failure to properly seat the flange/ clamp nut/
wheel could result in serious injury (or damage to the tool
or wheel).
CAUTION: To reduce the risk of personal injury,
wear work gloves when handling wire brushes and
wheels. They can become sharp.
CAUTION: To reduce the risk of damage to the tool,
wheel or brush must not touch guard when mounted
or while in use. Undetectable damage could occur to
the accessory, causing wires to fragment from accessory
wheel or cup.
Wire cup brushes or wire wheels install directly on the threaded
spindle without the use of flanges. Use only wire brushes or
wheels provided with a threaded hub. These accessories are
available at extra cost from your local dealer or authorised
service centre.
1. Place the tool on a table, guard up.
2. Thread the wheel on the spindle by hand.
3. Depress spindle lock button
hub of the wire wheel or brush to tighten the wheel.
4. To remove the wheel, reverse the above procedure.
NOTICE: To reduce the risk of damage to the tool, properly
seat the wheel hub before turning the tool on.
English
16
on
on the backing pad
.
16
3
, thread the clamp nut
4
by hand.
3
and use a wrench to
3
and use a wrench on the
18
13
Advertisement
Table of Contents
