Autel TBE200E Manual
  1. Manuals
  2. Brands
  3. Autel Manuals
  4. Measuring Instruments
  5. TBE200E
  6. Manual

Autel TBE200E Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Trademarks
®
Autel
, MaxiSys
®
MaxiCheck
are trademarks of Autel Intelligent Technology Corp., Ltd.,
registered in China, the United States, and other countries. All other marks are
trademarks or registered trademarks of their respective holders.
Copyright Information
No part of this manual may be reproduced, stored in a retrieval system or
transmitted, in any form or by any means, electronic, mechanical, photocopying,
recording, or otherwise without the prior written permission of Autel.
Disclaimer of Warranties and Limitation of Liabilities
All information, specifications, and illustrations in this manual are based on the
latest information available at the time of printing.
Autel reserves the right to make changes at any time without notice. While
information of this manual has been carefully checked for accuracy, no guarantee
is given for the completeness and correctness of the contents, including but not
limited to the product specifications, functions, and illustrations.
Autel will not be liable for any direct, special, incidental, nor indirect damages,
nor any economic consequential damages (including the loss of profits).
IMPORTANT
Before operating or maintaining this unit, please read this manual carefully,
paying extra attention to the safety warnings and precautions.
For Services and Support
pro.autel.com
www.autel.com
www.maxitpms.com
1-855-288-3587 (North America)
supporttpms@auteltech.com
For technical assistance in all other markets, please contact your local distributor.
®
®
, MaxiDAS
, MaxiScan
®
, MaxiTPMS
i
®
, MaxiRecorder
®
, and

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TBE200E and is the answer not in the manual?

Questions and answers

Related Manuals for Autel TBE200E

Summary of Contents for Autel TBE200E

  • Page 1 All information, specifications, and illustrations in this manual are based on the latest information available at the time of printing. Autel reserves the right to make changes at any time without notice. While information of this manual has been carefully checked for accuracy, no guarantee is given for the completeness and correctness of the contents, including but not limited to the product specifications, functions, and illustrations.

  • Page 2: Safety Messages

    Safety Information For your own safety and the safety of others, and to prevent damage to the device and vehicles upon which it is used, it is important that the safety instructions presented throughout this manual be read and understood by all persons operating or coming into contact with the device.

  • Page 3: Safety Instructions

    Safety Instructions The safety messages herein cover situations Autel is aware of. Autel cannot know, evaluate or advise you of all possible hazards. You must be certain that any condition or service procedure encountered does not jeopardize your personal safety.
  • Page 4  Refer to the service manual for the vehicle being serviced and adhere to all diagnostic procedures and precautions. Failure to do so may result in personal injury or damage to the test equipment.  To avoid damaging the test equipment or generating false data, make sure the vehicle battery is fully charged and the connection to the vehicle DLC is clean and secure.

  • Page 5: Table Of Contents

    CONTENTS ..................AFETY NFORMATION ..................AFETY ESSAGES ..................AFETY NSTRUCTIONS 1 USING THIS MANUAL ................... 1 ................... 1 ONVENTIONS 1.1.1 Bold Text ..................1 1.1.2 Notes and Important Messages ..........1 1.1.3 Hyperlink ..................1 1.1.4 Illustrations ................. 2 2 GENERAL INTRODUCTION ................3 TPMS TBE200 E ............
  • Page 6 ................19 UMBER OF TIRES ....................19 ..................19 ................ 20 READ HECK ..............20 RAKE IMIT 8 DATA QUERY ....................21 9 SYSTEM CALIBRATION ................22 10 SETTINGS ....................23 10.1 ..............23 ETWORK CONNECTION 10.2 ..................23 RIGHTNESS 10.3 .....................
  • Page 7 13.7 KC COMPLIANCE ................. 32 14 WARRANTY ....................33...

  • Page 8: Using This Manual

    1 Using This Manual This manual contains device usage instructions. Some illustrations shown in this manual may contain modules and optional equipment that are not included in your system. Contact your sales representative for availability of other modules and optional tools or accessories.

  • Page 9: Illustrations

    selectable hyperlink and blue underlined text indicates a website link or an email address link. 1.1.4 Illustrations Illustrations used in this manual are examples; actual testing screens may vary for each vehicle being tested. Carefully observe the menu titles and on- screen instructions to make the right selections.

  • Page 10: General Introduction

    2 General Introduction The Autel MaxiTPMS TBE200 Examiner (hereinafter referred to as “the tool”) is a laser-enabled tire & brake disc-wear examination tool that provides users with quick and accurate tire-wear measurements along with the ability to measure brake disc wear without having to remove tires. The tool's dual cameras enable users to document tire wear and damage as well as scan Tire Identification Numbers (TINs).
  • Page 11 Figure 2-2 Examiner Front View Power/Measure button — Press and hold this button for 3 seconds to power the tool on and off; select the desired application and press the button to take measurements. 1.65-inch AMOLED Screen Figure 2-3 Examiner Side View Magnetic Head...

  • Page 12: Power Sources

    Figure 2-4 Examiner Back View Camera Flash 8-megapixel Camera Laser Diode 1-megapixel Camera 2.1.2 Power Sources The tool can receive power from any of the following sources:  Internal Battery Pack  AC/DC Power Supply Internal Battery Pack The tool can be powered by its internal rechargeable battery, which theoretically, when fully charged can provide sufficient power for about 8 hours of continuous operation.

  • Page 13: Technical Specifications

    2.1.3 Technical Specifications Table 2-1 Technical Specifications Item Description Product Tire & Brake Disc Examiner Name Class 3R Laser Product Laser Classification IEC 60825-1:2014 Wave Length 520 nm Peak Emission Labelling Processor 4 x ARM Cortex-A35 (1.5 GHz) Memory 1 GB RAM LPDDR3 & 4GB On-board Memory 1.65-inch AMOLED touchscreen with 348 x 442 pixel Display resolution...
  • Page 14 Item Description  Wi-Fi Connectivity  USB Type C Micro- CMOS, 1 megapixel & 8 megapixel cameras Audio Output Output: beep with vibration Battery 3.7 V/3000 mAh 18650 lithium-ion battery Tested Around 8 hours of continuous use on one single charge Battery Life Battery Charging...

  • Page 15: Other Accessories

    2.2 Other Accessories Table 2-2 Accessories Power Adapter Used with USB cable to power and charge the tool via electrical outlet. Type C USB Cable Connect between the power adapter and the tool for powering and charging.

  • Page 16: Getting Started

    3 Getting Started Ensure the tool is connected to the Internet and is sufficiently charged (See Power Sources). The product should avoid the exposure of direct light, such as sunlight, or close-ranged torch light, and flashlight, during the actual operation of tire tread check, brake disc check, and calibration. 3.1 Power Up Press and hold the power button on the tool to switch it on.

  • Page 17: Application Buttons

    3.1.2 Application Buttons The table below briefly describes each of the applications on the TBE200. Table 3-1 Application Buttons Button Name Description Accesses the tool’s tire-tread check function. Tire Tread Tire Tread Check on page 11 for details. Launches the brake disc wear measurement Brake Disc function.

  • Page 18: Tire Tread Check

    4 Tire Tread Check Using laser technology, the Tire Tread application analyzes the wear of the tires on vehicles with no need to remove the tires. Place the tool on the tire, and the tool projects a laser beam. The wear measurement is then sent to the display screen with an accuracy within 0.1mm.

  • Page 19: Check Modes

    Icon Results Description Warning: wear level (Yellow) Recommend replacing. approaching critical value. (Red) Danger: Severe tire wear. Replace immediately. 4.1 Check modes There are two check modes available under the Tire Tread application: Single Check The Single Tire check measures the wear of each tire on the vehicle by examining the tread depth in the center area of the tire only.

  • Page 20: Details

    4.2 Details The Details screen shows a wide variety of tire wear information. After measurements are shown on the screen, select a wheel location, swipe left to view details of the chosen tire. Below are the main sections featured in the Details section: Graphic measurements —...

  • Page 21: Brake Disc Check

    5 Brake Disc Check Your MaxiTPMS TBE200 laser-enabled tool examines brake disc wear quickly and accurately. You can examine the wear status of a brake disc without the need to remove tires. Measurements displayed graphically. The Brake Disc function not only provides brake disc wear measurements, but also offers analysis to ensure driving safety.

  • Page 22: Check Mode

    5.1 Check mode Brake Disc Check The Brake Disc function checks for brake disc wear and provides wear analysis. This check mode focuses on brake disc measurements only.  To perform a Brake Disc Check Tap the Brake Disc application icon on the Main Job Menu. Place the tool on the disc surface and press the Power/Measure button to start measuring.

  • Page 23: Quick Check

    6 Quick Check The Quick Check function is specifically designed to measure the tires and brake discs in one session. This mode also provides a comprehensive analysis of tire and brake disc wear. Figure 6-1 Quick Check Screen Degree of wear status is illustrated by the colors below. Table 6-1 Possible Results for Measurements Brake Tire Tread Icon...

  • Page 24: Check Mode

    6.1 Check mode Quick Check The Quick Check function combines the measuring of the tread depth and brake disc wear.  To perform a Quick Check Tap the Quick Check application icon on the Main Job Menu. Place the tool first on the tire surface, and then on the disc surface, pressing the Power/Measure button to take measurements for each.
  • Page 25 Tire specification — view a series of options and manually enter tire information, including brand, tire model, size, structure type code, etc. Wear analysis — displays replacement recommendations for tires and brake discs. Figure 6-2 Details Screen...

  • Page 26: Check Settings

    7 Check Settings Tap the Check Settings application icon on the Main Job screen, a list of options will display. Adjust these tire-related settings to your preference for optimal All Tread check and Single Check results. 7.1 Number of tires The default tire number is four.

  • Page 27: Tread Check Mode

    7.4 Tread Check Mode This option allows you to choose between Single Check and All Tread Check before initiating a tread check measurement. After choosing the check mode, a check mark will display to the right of the active selection. 7.5 Brake Disc Wear Limit This option enables you to adjust the brake disc wear limit for brake disc checks.

  • Page 28: Data Query

    8 Data Query The Data Query function stores the results of the latest measurement session. After the tool is connected with the ITS600/ITS600 Pro tablet, the measurements of the previous session will display on the tablet screen automatically. Once a new measuring session starts, the previous test results will be replaced by new results.

  • Page 29: System Calibration

    9 System Calibration The System Calibration application is used to calibrate your examination tool for optimal measuring results. On the Main Job screen, tap the Sys. Calibration icon and place the magnetic head on the calibration table. Press the Power/Measure button to start.

  • Page 30: Settings

    Settings Access the Settings menu to adjust default settings and view information about the TBE200. The Settings menu includes the following: 10.1 Network connection This option is for connecting the tool to the Internet. There are two network types available: Wi-Fi and Wi-Fi Direct. Simply swipe the toggle to turn it on. NOTE Ensure you turn on both the Wi-Fi and Wi-Fi Direct toggles when pairing the tool with the ITS600/ITS600 Pro tablet for comprehensive inspection reports.

  • Page 31: Language And Region

    10.5 Language and region This option allows you to adjust the region for the TBE200. There are 19 regions available. Select the region where you will be using the device. A check mark will display to the right of the selected region. 10.6 About The About function provides information about the tool, including the manufacturer, model name, serial number, password, firmware version and...

  • Page 32: Maintenance And Service

    Maintenance and Service To ensure that the examination tool performs at its optimum level, we advise that the product maintenance instructions in this section are strictly followed. 11.1 Maintenance Instructions The following shows how to maintain your tool, together with precautions you should take: ...
  • Page 33 You may be attempting to use the tool in an overly hot/cold environment. Charge the tool in moderate temperatures.  Your tool may have not been connected to the charger properly. Check the connector. NOTE If the problems persist, please contact Autel's technical support personnel or your local selling agent.

  • Page 34: Service Procedures

    This section introduces information for technical support, repair service, and application for replacement or optional parts. 12.1 Technical Support If you have any question or problem on product operations, please contact us. AUTEL NORTH AMERICA  Phone: 1-855-288-3587 Monday-Friday 9am–6pm EST ...

  • Page 35: Repair Service

    Phone: +045 5948465  Email: sales.jp@autel.com; support.jp@autel.com  Address: 719, Nissou Building, 3-7-18, Shinyokohama, Kouhoku, Yokohama, Kanagawa, Japan 222-0033  Website: www.autel.com/jp/ AUTEL IMEA DMCC  Website: www.autel.com  Phone: +971 585 002709  Email: sales.imea@autel.com; imea-support@autel.com  Address: Office 1006-1010, Cluster C, Fortune Tower, Jumeirah Lakes Tower (JLT), Dubai, U.A.E...

  • Page 36: Other Services

    8th Floor, Building B1, Zhiyuan, Xueyuan Road, Xili, Nanshan, Shenzhen, 518055, China 12.3 Other Services You can purchase optional accessories directly from Autel authorized tool suppliers, and/or your local distributor or sales agent. Your purchase order should include the following information: ...

  • Page 37: Compliance Information

    Compliance Information 13.1 FCC Compliance FCC ID: WQ8TBE200 This device complies with Part 15 of the FCC rules and Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation.

  • Page 38: Sar

    Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 13.2 SAR The radiated output power of this device is below the FCC radio frequency exposure limits. Nevertheless, the device should be used in such a manner that the potential for human contact is minimized during normal operation.

  • Page 39: Mic Compliance

    Low Voltage Directive 2014/35/EU 13.6 MIC COMPLIANCE 13.7 KC COMPLIANCE R-C-WQ2-TBE200...
  • Page 40 Warranty Limited One Year Warranty Autel Intelligent Technology Corp., Ltd. (the Company) warrants to the original retail purchaser of this MaxiTPMS Tire & Brake Disc Examiner that should this product or any part thereof during normal usage and under normal...
  • Page 41 IMPORTANT All contents of the product may be deleted during the process of repair. You should create a back-up copy of any contents of your product before delivering the product for warranty service.

Table of Contents