HP Mini 110-3030 Maintenance And Service Manual
  1. Manuals
  2. Brands
  3. HP Manuals
  4. Laptop
  5. Mini 110-3030
  6. Maintenance and service manual

HP Mini 110-3030 Maintenance And Service Manual

Hp mini 110-3030: supplementary guide
Hide thumbs Also See for Mini 110-3030:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
HP Mini 110 and Compaq Mini CQ10
Maintenance and Service Guide

Advertisement

Table of Contents
loading

Related Manuals for HP Mini 110-3030

Summary of Contents for HP Mini 110-3030

  • Page 1 HP Mini 110 and Compaq Mini CQ10 Maintenance and Service Guide...
  • Page 2 Microsoft Corporation. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
  • Page 3 Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the device, do not place the device directly on your lap or obstruct the device air vents. Use the device only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.
  • Page 4 Safety warning notice...

  • Page 5: Table Of Contents

    Table of contents 1 Product description ... 1 2 External component identification ... 5 Identifying the hardware ... 5 Top components ... 6 TouchPad ... 6 Lights ... 7 Keys ... 8 Front components ... 8 Right-side components ... 10 Left-side components ...
  • Page 6 Component replacement procedures ... 32 Service tag ... 32 Computer feet ... 33 Battery ... 34 SIM ... 35 Service cover ... 36 Hard drive ... 36 WWAN module ... 39 WLAN module ... 42 Memory module ... 45 RTC battery ... 47 Keyboard ...
  • Page 7 Creating a system restore point ... 77 Restoring to a previous date and time ... 77 Backing up and recovering using HP Recovery Manager ... 78 Backing up your information ... 78 Creating a set of recovery discs ... 79 Performing a recovery ...
  • Page 8 viii...

  • Page 9: Product Description

    Product description Category Description Product Name HP Mini 110 Compaq Mini CQ10 Processor Intel® Atom™ N475 1.83-GHz processor, 512-KB level 2 cache, 667-MHz front-side bus (FSB). 6.5W TDP Intel® Atom™ N470 1.83-GHz processor, 512-KB level 2 cache, 667-MHz front-side bus (FSB). 6.5W TDP Intel®...
  • Page 10 Broadcom 4312G 802.11b/g WiFi Adapter module ● Broadcom 4312G 802.11b/g WiFi and 2070 Bluetooth 2.1+EDR Combo Adapter module 2 WLAN antennas built into display assembly Integrated WWAN by way of HP un2400 Mobile Broadband Module (optional) HP Mini 110 Compaq Mini CQ10 √...
  • Page 11 3-pin AC power Keyboard/ 93% flat-style keyboard pointing device HP Clikpad TouchPad with multi-touch/gesture support No numeric pad supported. TouchPad with 2 TouchPad buttons and 2-way scrolling (taps enabled and some gestures enabled by default) TouchPad on/off button with LED indicator...
  • Page 12 Category Serviceability Chapter 1 Product description Description Windows XP Home SP3, ultra low-cost personal computer (ULCPC) edition Support for HP QuickWeb FreeDOS End-user replaceable parts: AC adapter Battery (system) Hard drive Memory module WLAN module WWAN module HP Mini 110...

  • Page 13: External Component Identification

    External component identification Identifying the hardware Components included with the computer may vary by region and model. The illustrations in this chapter identify the standard features on most computer models. To see a list of hardware installed in the computer, follow these steps: Select Start >...

  • Page 14: Top Components

    Top components TouchPad Item Component TouchPad on/off button TouchPad Left TouchPad button* Right TouchPad button* *This table describes factory settings. To view or change pointing device preferences, select Start > Control Panel > Printers and Other Hardware > Mouse. Chapter 2 External component identification Description Turns the TouchPad on and off.

  • Page 15: Lights

    Lights Item Component TouchPad light Caps lock light Mute light Wireless light Description ● On: The TouchPad is disabled. ● Off: The TouchPad is enabled. On: Caps lock is on. On: Speaker sound is off. ● White: An integrated wireless device, such as a wireless local area network (WLAN) device and/ or a Bluetooth device, is on.

  • Page 16: Keys

    Keys Item Component Windows logo key Windows applications key Arrow keys Action keys Front components Chapter 2 External component identification Description Displays system information when pressed in combination with the key. Executes frequently used system functions when pressed in combination with a function key or the Displays the Windows Start menu.
  • Page 17 Component Vents (2) Speaker Description Enable airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation. Produces sound.

  • Page 18: Right-Side Components

    To learn more about your power settings, select Start > Control Panel > System and Security > Power Options, or refer to the HP Notebook Reference Guide. Connect optional USB devices. Connects a network cable. Attaches an optional security cable to the computer.

  • Page 19: Left-Side Components

    Left-side components item Component Power connector AC adaptor light External monitor port Vent Drive light USB port Audio-out (headphone) jack/Audio-in (microphone) jack Description Connects an AC adapter. ● White: The computer is connected to external power and the battery is fully charged. ●...

  • Page 20: Display Components

    Send and receive wireless signals to communicate with wireless local area networks (WLAN). On: The webcam is in use. Records video and captures still photographs. To use the webcam, select Start > HP > HP MediaSmart > HP MediaSmart Webcam. Records sound.

  • Page 21: Bottom Components

    Bottom components item Component Battery release latches (2) Battery bay Description Release the battery from the battery bay. Holds the battery. Bottom components...

  • Page 22: Illustrated Parts Catalog

    Illustrated parts catalog Service tag When ordering parts or requesting information, provide the computer serial number and model description provided on the service tag: NOTE: The computer battery must be removed to access the service tag. (1) Product name: This is the product name affixed to the front of the device. (2) Serial number (s/n): This is an alphanumeric identifier that is unique to each product.

  • Page 23: Computer Major Components

    Computer major components Computer major components...
  • Page 24 Item Description 10.1-in display assembly (includes display panel cable, 2 WLAN transceivers and cables, 2 WWAN transceivers and cables, and webcam/microphone module and cable): ● 10.1-in, WSVGA, AntiGlare, standard display assembly in black ● 10.1-in, WSVGA, AntiGlare, standard display assembly in white ●...
  • Page 25 6-cell, 55-WHr (includes 2 release latches and 2 rubber feet) (13) Memory module (667-MHz, DDR2): 1024-MB 2048-MB (14) Memory shield (included with the service cover kit) (15) HP un2400 Mobile Broadband WWAN module Spare part number 608769-121 608769-001 607766-001 608770-001 607766-001 607740-001...
  • Page 26 Item Description (16) WLAN module Atheros 9285G 802.11b/g/n 1×1 WiFi Adapter module: ● For use in Canada, the Cayman Islands, Guam, Puerto Rico, the U.S. Virgin Islands, and the United States ● For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria,...

  • Page 27: Display Assembly Components

    Description Display bezel (includes WLAN antenna transceivers and cables and WWAN antenna transceivers and cables): For use only with HP Mini 110 computer models For use only with Compaq Mini CQ10 computer models For use only with Compaq Mini CQ10 computer models (black, hinge caps attached)
  • Page 28 Item Description 10.1-in, WSVGA, AntiGlare display panel non-PMMA with WWAN Display Hinge Kit (includes left and right display hinges) (5a) Display panel cable (includes webcam/microphone module cable) (5b) WWAN antenna cables (included in Display cable kit) (5c) WLAN antenna cables (included in Display cable kit) Display enclosure (includes WLAN antenna transceivers and cables and WWAN antenna transceivers and cables): 10.1-in, WSVGA, AntiGlare, standard display assembly in black...

  • Page 29: Mass Storage Devices

    Mass storage devices NOTE: Each hard drive spare part kit includes a cable adapter, bracket, and 4 isolators. Item Description Hard drive: 250-GB, 5400-RPM Spare part number 608763–001 Mass storage devices...

  • Page 30: Miscellaneous Parts

    Miscellaneous parts Description 30-W UMA AC adapter 30–W AC adapter Power cord: For use in Argentina For use in Australia For use in Brazil For use in Denmark For use in Europe, Middle East, and Africa For use in Israel For use in Italy For use in Japan For use in the People's Republic of China...

  • Page 31: Sequential Part Number Listing

    10.1-in, WSVGA, AntiGlare, standard display assembly in black (IMR) 10.1-in, AntiGlare display panel non PMMA Webcam/microphone module Display bezel for use with HP models (includes WLAN antenna transceivers and cables and WWAN antenna transceivers and cables): Service cover (black) Sequential part number listing...
  • Page 32 6-cell, 55-WHr (includes 2 release latches and 2 rubber feet) 30–W AC adapter Base enclosure (includes 4 rubber feet and power connector bracket) Top cover (for HP and CPQ) Service cover (kit includes memory shield) Hard drive: 250-GB, 5400-rpm Keyboard with textured finish for use only in the United States (includes cable)
  • Page 33 Spare part number Description 608769–AD1 Keyboard with textured finish for use only in South Korea (includes cable) 608769–B31 Keyboard with textured finish for use only in the Netherlands (includes cable) 608769–BA1 Keyboard with textured finish for use only in Slovenia (includes cable) 608769–BB1 Keyboard with textured finish for use only in Israel (includes cable) 608769–BG1...
  • Page 34 Spare part number 620300–001 620301–001 620302–001 620303–001 620902–001 621300-001 621301-001 621302-001 621303-001 Chapter 3 Illustrated parts catalog Description Intel Atom N450 1.66-GHz processor with 512-KB level 2 cache, 667-MHz FSB without WWAN module Intel Atom N470 1.83-GHz processor with 512-KB level 2 cache, 667-MHz FSB, 6.5W TDP without WWAN module Intel Atom N455 1.66-GHz processor with 512-KB level 2 cache, 667-MHz FSB without WWAN module...

  • Page 35: Removal And Replacement Procedures

    Removal and replacement procedures Preliminary replacement requirements Tools required You will need the following tools to complete the removal and replacement procedures: ● Flat-bladed screwdriver ● Magnetic screwdriver ● Phillips P0 and P1 screwdrivers Service considerations The following sections include some of the considerations that you must keep in mind during disassembly and assembly procedures.

  • Page 36: Cables And Connectors

    Cables and connectors CAUTION: When servicing the device, be sure that cables are placed in their proper locations during the reassembly process. Improper cable placement can damage the device. Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat or seat the cables during removal and insertion.

  • Page 37: Grounding Guidelines

    Grounding guidelines Electrostatic discharge damage Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure determine the degree of sensitivity. Networks built into many integrated circuits provide some protection, but in many cases, ESD contains enough power to alter device parameters or melt silicon junctions.

  • Page 38: Packaging And Transporting Guidelines

    Packaging and transporting guidelines Follow these grounding guidelines when packaging and transporting equipment: ● To avoid hand contact, transport products in static-safe tubes, bags, or boxes. ● Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging. ● Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations.

  • Page 39: Equipment Guidelines

    Equipment guidelines Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation. ● When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground, wear a strap snugly against the skin at all times.

  • Page 40: Component Replacement Procedures

    Component replacement procedures This chapter provides removal and replacement procedures. There are as many as 33 screws, in 5 different sizes, that must be removed, replaced, or loosened when servicing the computer. Make special note of each screw size and location during removal and replacement.

  • Page 41: Computer Feet

    Computer feet The computer feet are adhesive-backed rubber pads. The feet are included in the Rubber Feet Kit, spare part number 607756-001. There are 4 rubber feet that attach to the base enclosure in the locations shown in the following illustration. Component replacement procedures...

  • Page 42: Battery

    Battery Description 6-cell, 55-WHr (includes 2 release latches and 2 rubber feet) 3-cell, 27-WHr (includes 2 release latches) Before disassembling the computer, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.

  • Page 43: Sim

    Before removing the SIM, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. Disconnect all external devices connected to the computer. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.

  • Page 44: Service Cover

    Service cover Description Service cover Before removing the service cover, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. Disconnect all external devices connected to the computer.
  • Page 45 Description Hard drive: 250-GB, 5400-RPM Before removing a hard drive, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. Disconnect all external devices connected to the computer.
  • Page 46 Slide the tab (1) to disconnect the hard drive from the computer, and then lift the hard drive (2) out of the bay. Reverse this procedure to reassemble and install the hard drive. Chapter 4 Removal and replacement procedures...

  • Page 47: Wwan Module

    WWAN module Description HP un2400 Mobile Broadband WWAN module CAUTION: The WWAN module and the WLAN module are not interchangeable. To prevent an unresponsive system, replace the wireless module only with a wireless module authorized for use in the computer by the governmental agency that regulates wireless devices in your country or region.
  • Page 48 Using a small Phillips screwdriver, remove the 2 module screws. This releases the module and allows it to tilt up at a slight angle. Remove the WWAN module. Reverse this procedure to install the WWAN module. NOTE: When replacing the WWAN module, press the antenna cables firmly down onto the terminals until securely connected.
  • Page 49 Component replacement procedures...

  • Page 50: Wlan Module

    WLAN module Description Atheros 9285G 802.11b/g/n 1×1 WiFi Adapter module: For use in Canada, the Cayman Islands, Guam, Puerto Rico, the U.S. Virgin Islands, and the United States For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde,...
  • Page 51 Remove the WLAN module: Disconnect the WLAN antenna cables NOTE: The number of WLAN cables varies, depending on model. Note the labeling and position of the cables. Disconnect the antenna cables by pulling the cables off the terminals. Using a small Phillips screwdriver, remove the 2 WLAN module screws. This releases the module to tilt up at a slight angle Component replacement procedures...
  • Page 52 Lift up and remove the WLAN module at an angle. Reverse this procedure to install the WLAN module. NOTE: When replacing, press the antenna cables firmly down onto the terminals until securely connected. Route the cables carefully to prevent potential damage when the service cover is replaced, as shown in the illustration below.

  • Page 53: Memory Module

    Memory module Description 2048-MB memory module (667-MHz, DDR2) 1024-MB memory module (667-MHz, DDR2) Before removing the memory module, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. Disconnect all external devices connected to the computer.
  • Page 54 Lift up and remove the memory shield. Using your fingers, spread the 2 retention clips outward until the memory module tilts up at a 45- degree angle. Remove the memory expansion module from the computer. Reverse this procedure to install the memory module. Chapter 4 Removal and replacement procedures...

  • Page 55: Rtc Battery

    RTC battery Description RTC battery Before removing the real-time clock (RTC) battery, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. Disconnect all external devices connected to the computer.

  • Page 56: Keyboard

    Keyboard NOTE: The keyboard spare part kit includes a keyboard cable. For use in: With textured finish: Belgium Brazil The Czech Republic Denmark, Finland, and Norway France French Canada Germany Greece Hungary Israel Italy Japan Latin America Before removing the keyboard, follow these steps: Shut down the computer.
  • Page 57 Remove the keyboard: Remove the three Phillips PM2.0×6.0 screws that secure the keyboard to the computer. Turn the computer right-side up, with the front toward you. Open the computer as far as it will open. Lift the rear edge of the keyboard (1) until it rests at an angle. Slide the keyboard (2) back until the keyboard cable and connector are accessible.
  • Page 58 Release the zero insertion force (ZIF) connector (3) to which the keyboard cable is attached, and then disconnect the keyboard cable (4) from the system board. Remove the keyboard. Reverse this procedure to install the keyboard. Chapter 4 Removal and replacement procedures...

  • Page 59: Top Cover

    Top cover Description In black (for HP and CPQ) Before removing the top cover, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
  • Page 60 Release the ZIF connector (2) to which the TouchPad cable is connected, and then disconnect the TouchPad cable (3) from the system board. Chapter 4 Removal and replacement procedures...
  • Page 61 Remove the five Phillips PM2.0×6.0 screws that secure the top cover to the base enclosure. Release the top cover (1) by lifting the rear edge until it disengages from the base enclosure. Remove the top cover (2) by lifting it straight up. Reverse this procedure to install the top cover.

  • Page 62: Speakers

    Speakers Description Speakers (include cables) Before removing the speakers, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. Disconnect all external devices connected to the computer.
  • Page 63 Remove the speakers (4). Reverse this procedure to install the speakers. Component replacement procedures...

  • Page 64: Touchpad

    TouchPad Description For use only with a black top cover Before removing the TouchPad, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. Disconnect all external devices connected to the computer.
  • Page 65 Remove the TouchPad (5) by sliding it forward. Reverse this procedure to install the TouchPad. Component replacement procedures...

  • Page 66: Display Assembly

    Display assembly Description 10.1-in display assembly (includes display panel cable, 2 WLAN transceivers and cables, 2 WWAN transceivers and cables, and webcam/microphone module and cable): ● 10.1-in, WSVGA, AntiGlare, standard display assembly in black ● 10.1-in, WSVGA, AntiGlare, standard display assembly in white ●...
  • Page 67 Release the WLAN antenna cables (1) from the clips built into the base enclosure (2). Turn the computer right-side up, with the front toward you. Open the computer as far as it will open. Disconnect the display panel cable (1) from the system board. Component replacement procedures...
  • Page 68 Release the wireless antenna cables (2) from the clip built into the base enclosure. CAUTION: support the display assembly can result in damage to the display assembly and other device components. Remove the two Phillips PM2.0×4.0 screws (1) that secure the display assembly to the base enclosure.
  • Page 69 Remove the display assembly (2). Reverse this procedure to reassemble and install the display assembly. Component replacement procedures...

  • Page 70: System Board

    System board NOTE: The system board spare part kit includes replacement thermal material. Description Intel Atom N450 1.66-GHz processor with 512-KB level 2 cache, 667-MHz FSB Intel Atom N470 1.83-GHz processor with 512-KB level 2 cache, 667-MHz FSB, 6.5W TDP Intel Atom N455 1.66-GHz processor with 512-KB level 2 cache, 667-MHz FSB Intel Atom N475 1.83-GHz processor with 512-KB level 2 cache, 667-MHz FSB, 6.5 TDP Intel Atom N450 1.66-GHz processor with 512-KB level 2 cache, 667-MHz FSB without WWAN...
  • Page 71 ● WLAN module (see WLAN module on page ● Memory module (see Memory module on page ● RTC battery (see RTC battery on page ● Fan/heat sink assembly (see Remove the system board: Disconnect the display panel cable from the system board. Disconnect the power connector cable from the system board.
  • Page 72 Remove the system board (3) by sliding it up and away from the base enclosure. Reverse the procedure to install the system board. NOTE: When reinstalling the system board, the base enclosure actuator needs to be aligned properly with the power switch so that the parts are not damaged in the installation process. Chapter 4 Removal and replacement procedures...

  • Page 73: Fan/Heat Sink Assembly

    Fan/heat sink assembly Description Fan/heat sink assembly (includes replacement thermal material) NOTE: To properly ventilate the computer, allow at least a 7.6-cm (3-inch) clearance on the left side of the computer. The computer uses an electric fan for ventilation. The fan is controlled by a temperature sensor and is designed to turn on automatically when high temperature conditions exist.
  • Page 74 Remove the fan/heat sink assembly (3). NOTE: Due to the adhesive quality of the thermal material located between the fan/heat sink assembly and system board components, it may be necessary to move the fan/heat sink assembly from side to side to detach it from the system board. NOTE: The thermal material must be thoroughly cleaned from the surfaces of the fan/heat sink assembly and the system board each time the fan/heat sink assembly is removed: Thermal paste is...

  • Page 75: Power Connector Cable

    Power connector cable Description Power connector cable Before removing the power connector cable, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. Disconnect all external devices connected to the computer.
  • Page 76 Remove the power connector cable . Reverse this procedure to install the power connector cable. Chapter 4 Removal and replacement procedures...

  • Page 77: Setup Utility

    Setup Utility Starting Setup Utility Setup Utility is a ROM-based information and customization utility that can be used even when your Windows operating system is not working. The utility reports information about the computer and provides settings for startup, security, and other preferences.

  • Page 78: Navigating And Selecting In Setup Utility

    Navigating and selecting in Setup Utility Because Setup Utility is not Windows based, it does not support the TouchPad. Navigation and selection are by keystroke. ● To choose a menu or a menu item, use the arrow keys. ● To choose an item in a list or to toggle a field, for example an Enable/Disable field, use either the arrow keys or ●...

  • Page 79: Exiting Setup Utility

    Exiting Setup Utility You can exit Setup Utility with or without saving changes. ● To exit Setup Utility and save your changes from the current session: If the Setup Utility menus are not visible, press arrow keys to select Exit > Exit Saving Changes, and then press enter. ●...

  • Page 80: System Configuration Menu

    Delay (sec.)―Set the delay for the functions of Setup Utility in intervals of 5 seconds each (0, 5, 10, 15, 20). ● HP QuickWeb―Enable/disable the QuickWeb Boot menu in Setup Utility. ● Internal Network Adapter boot―Enable/disable boot from Internal Network Adapter.

  • Page 81: Backup And Recovery (Windows Only)

    In the event of a hard drive failure, you cannot use your computer to access the Disaster Recovery utility. Therefore, HP recommends that you download the Disaster Recovery utility SoftPaq, and then extract it to a USB flash drive as soon as possible after software setup. For details, refer to “Downloading and extracting the Disaster Recovery utility”...

  • Page 82: Creating A Copy Of The Hard Drive

    To copy the screen and paste it into a word-processing document, follow these steps: Display the screen. Copy the screen: To copy the active window, press Open a word-processing document, click Edit, and then click Paste. Save the document. Creating a copy of the hard drive The back up drive function of BackOnTrack creates a Disaster Recovery Set that is an exact image of your hard drive data.

  • Page 83: Using The Disaster Recovery Utility

    For optimum performance, the capacity of the drive should be no larger than 2 GB. Disaster Recovery recovers data from a Disaster Recovery Set that you previously created with Roxio BackOnTrack. Disaster Recovery is available from the HP Web site in a compressed file called a SoftPaq.

  • Page 84: Using The Instant Restore Utility

    Using the Instant Restore utility You can restore your computer from Windows when the operating system is functioning. If the operating system is not functioning, you can also access the utility by restarting your computer. NOTE: For more information about the Instant Restore utility, refer to the BackOnTrack software Help. Using the Instant Restore utility when the operating system is functioning To recover information when the operating system is functioning properly, follow these steps: Save and close all open documents and close any open programs.

  • Page 85: Using System Restore Points

    Using system restore points When you back up your system, you are creating a system restore point. A system restore point allows you to save and name a snapshot of your hard drive at a specific point in time. You can then revert back to that point if you want to reverse subsequent changes made to your system.

  • Page 86: Backing Up And Recovering Using Hp Recovery Manager

    Backing up and recovering using HP Recovery Manager If your computer includes HP Recovery Manager, tools provided by the operating system and by HP Recovery Manager software are designed to help you with the following tasks for safeguarding your information and restoring it in case of a system failure: ●...

  • Page 87: Creating A Set Of Recovery Discs

    Creating a set of recovery discs HP recommends that you create recovery discs to be sure that you can restore your system to its original factory state if you experience serious system failure or instability. Create these discs after setting up the computer for the first time.

  • Page 88: Performing A Recovery

    Performing a recovery NOTE: You can recover only files that you have previously backed up. HP recommends that you use Recovery Manager to create a set of recovery discs (entire drive backup) as soon as you set up your computer.

  • Page 89: Windows Xp

    In the event of a hard drive failure, you cannot use your computer to access the Disaster Recovery utility. Therefore, HP recommends that you download the Disaster Recovery utility SoftPaq, and then extract it to a USB flash drive as soon as possible after software setup. For details, refer to “Downloading and extracting the Disaster Recovery utility”...

  • Page 90: Creating A Copy Of The Hard Drive

    Creating a copy of the hard drive The back up drive function of BackOnTrack creates a Disaster Recovery Set that is an exact image of your hard drive data. You can back up the image to an external hard drive (purchased separately). To create a Disaster Recovery Set using BackOnTrack, follow these steps: NOTE: Be sure that the computer is connected to AC power before you start the backup process.

  • Page 91: Using The Disaster Recovery Utility

    For optimum performance, the capacity of the drive should be no larger than 2 GB. Disaster Recovery recovers data from a Disaster Recovery Set that you previously created with Roxio BackOnTrack. Disaster Recovery is available from the HP Web site in a compressed file called a SoftPaq.

  • Page 92: Using The Instant Restore Utility

    Using the Instant Restore utility You can restore your computer from Windows when the operating system is functioning. If the operating system is not functioning, you can also access the utility by restarting your computer. NOTE: For more information about the Instant Restore utility, refer to the BackOnTrack software Help. Using the Instant Restore utility when the operating system is functioning To recover information when the operating system is functioning properly, follow these steps: Save and close all open documents and close any open programs.

  • Page 93: Connector Pin Assignments

    Connector pin assignments Audio-in (microphone) Audio-out (headphone) Signal Audio signal in Audio signal in Ground Signal Audio out, left channel Audio out, right channel Ground Audio-in (microphone)

  • Page 94: External Monitor

    External monitor Chapter 7 Connector pin assignments Signal Red analog Green analog Blue analog Not connected Ground Ground analog Ground analog Ground analog +5 VDC Ground Monitor detect DDC 2B data Horizontal sync Vertical sync DDC 2B clock...

  • Page 95: Network)

    RJ-45 (network) Universal Serial Bus Signal Transmit + Transmit - Receive + Unused Unused Receive - Unused Unused Signal +5 VDC Data Data + Ground RJ-45 (network)

  • Page 96: Power Cord Set Requirements

    Power cord set requirements The wide-range input feature of the computer permits it to operate from any line voltage from 100 to 120 volts AC, or from 220 to 240 volts AC The 3-conductor power cord set included with the computer meets the requirements for use in the country or region where the equipment is purchased.

  • Page 97: Requirements For Specific Countries And Regions

    Requirements for specific countries and regions Country/region Australia Austria Belgium Canada Denmark Finland France Germany Italy Japan The Netherlands Norway The People's Republic of China South Korea Sweden Switzlerland Taiwan The United Kingdom The United States The flexible cord must be Type HO5VV-F, 3-conductor, 1.0-mm² conductor size. Power cord set fittings (appliance coupler and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used.

  • Page 98: Recycling

    When you remove these components, handle them carefully. NOTE: Materials Disposal. This HP product contains mercury in the backlight in the display assembly that might require special handling at end-of-life. Disposal of mercury may be regulated because of environmental considerations. For disposal or recycling information, contact your local authorities, or see the Electronic Industries Alliance (EIA) Web site at http://www.eiai.org.
  • Page 99 Perform the following steps: Remove all screw covers (1) and screws (2) that secure the display bezel to the display assembly. Lift up and out on the left and right inside edges (1) and the top and bottom inside edges (2) of the display bezel until the bezel disengages from the display assembly.
  • Page 100 Disconnect all display panel cables (1) from the display inverter and remove the inverter 2. Remove all screws (1) that secure the display panel assembly to the display enclosure. Remove the display panel assembly (2) from the display enclosure. Turn the display panel assembly upside down. Remove all screws that secure the display panel frame to the display panel.
  • Page 101 Remove the display panel frame (2) from the display panel. Remove the screws (1) that secure the backlight cover to the display panel. Lift the top edge of the backlight cover (2) and swing it outward. Remove the backlight cover. Turn the display panel right-side up.
  • Page 102 Remove the backlight cables (1) from the clip (2) in the display panel. Turn the display panel upside down. Remove the backlight frame from the display panel. WARNING! backlight to avoid damaging this component and causing exposure to the mercury. Chapter 9 Recycling The backlight contains mercury.
  • Page 103 Remove the backlight from the backlight frame. Disconnect the display cable (1) from the LCD panel. Remove the screws (2) that secure the LCD panel to the display rear panel. Release the LCD panel (3) from the display rear panel. Release the tape (4) that secures the LCD panel to the display rear panel.

  • Page 104: Index

    Index AC adapter spare part number 22, 23, 24 AC adapter, spare part number 22 AC adaptor light 11 action keys 8 audio, product description 2 audio-in jack connector pinout 85 location 11 audio-out jack connector pinout 85 location 11 back cover spare part number 23, 24 base access door...
  • Page 105 product description 2 removal 37 self test 72 spare part numbers 18, 21, 24, 37 headphone jack connector pinout 85 location 11 hinge, spare part number 20, 25 internal media cards, product description 3 jacks audio-in 11 audio-out 11 headphone 11 microphone 11 network 10 RJ-45 10...
  • Page 106 service considerations 27 service cover removal 36 spare part number 18, 36 service tag 14, 32 serviceability, product description 4 Setup Utility changing the language 69 Diagnostics Menu 72 exiting 71 Main Menu 71 menus 71 navigating 70 restoring default settings 70 Security Menu 71 selecting 70 starting 69...

This manual is also suitable for:

Mini 110Compaq mini cq10

Table of Contents