Table of Contents
Advertisement
Quick Links
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in residential installation.
This equipment generates, uses and can radiate radio frequency energy and if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, detectable by turning the equipment in question off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna
Increase the distance between the equipment and the receiver
Connect the equipment to an outlet on a different circuit than that which the receiver
is connected to
Or consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to following
two conditions:
1.This device may not cause harmful interference, and
2.This device must accept any interference that may cause undesired operation.
FCC Notice
Projector
User's Manual
○ ○ ○ ○ ○ ○ ○ ○ ○ ○
EN-1
Advertisement
Table of Contents
Related Manuals for BOXLIGHT SP-48Z
Summary of Contents for BOXLIGHT SP-48Z
- Page 1 Projector User’s Manual FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
- Page 2 Projector User’s Manual Precautions Safety Instructions 1. Check that the operating voltage of your unit is identical with the voltage of your local power supply. 2. Should any liquid or solid object fall into the cabinet, unplug the unit and have it checked by the qualified personnel before operating it further.
- Page 3 Projector User’s Manual Cautions The projector is equipped with ventilation holes (intake) and ventilation holes (exhaust). Do not block or place anything near these slots, or internal heat build- up may occur, causing picture degradation or damage to the projector. When you replace the projector lamp, never touch the new bulb with your bare hands.
-
Page 4: Table Of Contents
Projector User’s Manual CONTENTS Projector Features and Controls Projector Control Panel Remote Controller Button Function Getting the Most Out of Your Projector Remote Controller Auto Off Mode Control Panel Setup Unpacking the Projector Setting Up the Projector Connecting to a Computer Connecting to a Video Source Using the Projector Turning the Audio/Visual(A/V) Equipment On and Off... - Page 5 Projector User’s Manual Audio Menu MISC Menu Option Menu Language Menu Reset Menu Other Related OSD Menus Video Input Signal Video Menu Other OSD Menus No Input Signal Maintenance Cleaning the Lens Cleaning the Projector Housing Cleaning the Air Filter Replacing the Lamp Technical Specifications Appendix A...
-
Page 6: Projector Features And Controls
Projector User’s Manual PROJECTOR FEATURES AND CONTROLS PROJECTOR 1. Zoom ring 2. Focus ring 3. Lens 4. Ventilation holes (intake) 5. Ventilation holes (exhaust) 6. Adjuster button 7. Front IR remote controller sensor 8. Speakers 9. Control Panel including Power button 10. -
Page 7: Control Panel
Projector User’s Manual CONTROL PANEL POWER Power LED indicator – indicates power to projector. LAMP Lamp LED indicator – indicates lamp power. Button Function Turns the projector and lamp ON and OFF. INPUT Manually selects an input source. AUTO Automatically adjusts frequency and phase. MENU Displays (or hides) the on-screen control menus. -
Page 8: Remote Controller
Projector User’s Manual REMOTE CONTROLLER Button Function Power Turns the projector and lamp ON and OFF. Menu Displays (or hides) the on-screen display menus. Scrolls up through the menu choices. Scrolls down through the menu choices. Increases the value setting on the selected sub-menus, or confirms a menu selection. -
Page 9: Getting The Most Out Of Your Projector
Projector User’s Manual GETTING THE MOST OUT OF YOUR PROJECTOR The projector has a full set of features that allow you to control the settings for video, audio, power management, display parameters, and much more. To derive the greatest utility from your projector, read this section for a quick summary of the important features. -
Page 10: Setup
Projector User’s Manual SETUP This section tells you how to unpack and set up your projector and connect it to other equipment. The projector must be connected to a computer or a video source such as a video tape deck, camcorder, digital camera or laser disk player in order to make a projection. -
Page 11: Setting Up The Projector
Projector User’s Manual Setting Up the Projector 1.Place the projector on a sturdy, level surface within five feet of the computer or video source. Caution: Do not hold the projector by the lens. This can damage the lens. 2. Place the projector at the correct distance from the screen. The distance between the projector and the screen determines the actual image size. -
Page 12: Connecting To A Computer
Projector User’s Manual Connecting to a Computer Audio Cable Projector Computer Computer Cable VGA OUT The projector will always project at SVGA (800 x 600) resolution. (SVGA is the native resolution of the projector.) However, you can connect the projector to a computer source capable of displaying VGA (640 x 480), SVGA (800 x 600), XGA (1024 x 768) or SXGA (1280 x 1024) resolutions. -
Page 13: Connecting To A Video Source
Projector User’s Manual Connecting to a Video Source Video out VCR AV Composite Cable S-Video Cable DVD Player YPbPr (HDTV to D-SUB Cable) Y Cb Cr(Component Video Cable) You can connect the projector to almost any common video source - VHS player, DVD player, camcorder, laser disc player or any other compatible video image source. -
Page 14: Using The Projector
Projector User’s Manual Using the Projector This section describes projector operations: Turning the projector and A/V equipment on and off Adjusting the projected image Projector controls Checking the projector status Turning the Audio/Visual (A/V) Equipment On and Always turn on the projector and related A/V equipment in the following order. 1.Projector 2.Computer 3.Video source... -
Page 15: Focusing And Positioning The Screen Image
Projector User’s Manual 5.To turn off the projector, press the Power button. A message will appear on the screen for about 10 seconds: 6.Press the Power button once again(to turn off the power) while the message is still showing on the screen. Note: Please wait until the fan motor and the Lamp LED turn off before removing the power cord from the projector. -
Page 16: Projector Control Menus
Projector User’s Manual LED TYPE COLOR STATUS MEANING Power LED Green Solid The projector is powered and ready. Power LED Solid The projector system has some problems with its fan, so the projector cannot start up. Lamp LED Green Solid The lamp is in good condition and is projecting at maximum brightness. - Page 17 Projector User’s Manual 2.Selecting the desired menu or sub-menu(to scroll through the menu choices): On the Projector Control Panel: press the button. On the Remote Controller: press the button. Note: To scroll up: press the button. To scroll down: press the button.
-
Page 18: Menu Options
Projector User’s Manual Menu Options The projector is equipped with three types of on-screen display(OSD) menus. Each OSD menu interface you will see on the screen is depending on the type of input signal. * The illustrations in this manual are for the purpose of explanation and may differ from the actual setting of your projector. -
Page 19: Input Menu
Projector User’s Manual Input Menu This menu allows to specify the signal source that you wish to project. This is particularly useful if you have several sources (video and/or computer) connected to your projector. Changing settings procedure (using either the Projector Control Panel or the Remote Controller): 1. - Page 20 Projector User’s Manual Changing settings procedure (using either the Projector Control Panel or the Remote Controller): 1. Press the MENU button to display OSD menu. 2. Press the button to select PICTURE menu. 3. To enter the sub-menu setting, press the button or the MENU button.
-
Page 21: Color Menu
Projector User’s Manual Color Menu This menu provides precise control of the color settings including: color temperature (preset & user define) and gamma. Changing settings procedure (using either the Projector Control Panel or the Remote Controller): 1.Press the MENU button to display OSD menu. -
Page 22: Audio Menu
Projector User’s Manual Audio Menu This menu allows you to control volume and mute(On/Off) the audio. Changing settings procedure (using either the Projector Control Panel or the Remote Controller): 1.Press the MENU button to display OSD menu. 2.Press the button to select AUDIO menu. -
Page 23: Misc Menu
Projector User’s Manual MISC Menu This menu includes projector utilities for vertical keystone, freeze (Yes/No) and blank (Yes/No) mode settings. Changing settings procedure (using either the Projector Control Panel or the Remote Controller): 1. Press the MENU button to display OSD menu. -
Page 24: Option Menu
Projector User’s Manual Option Menu This menu includes projector utilities for OSD timeout, OSD horizontal position, OSD vertical position, rear mode, ceiling mode, aspect ratio, auto off and lamp life indication. Changing settings procedure (using either the Projector Control Panel or the Remote Controller): 1.Press the MENU button to display OSD menu. - Page 25 Projector User’s Manual The following table provides detail of the available sub-menu choices: Sub-Menu Option Description OSD Timeout Duration OSD menu stays active (at idle state). OSD PosiH Adjusts OSD menu display position (horizontally - left & right) on the screen. OSD PosiV Adjusts OSD menu display position (vertically - up &...
-
Page 26: Language Menu
Projector User’s Manual Language Menu This menu enables you to select the language used in the OSD (on-screen display) menus. Changing settings procedure (using either the Projector Control Panel or the Remote Controller): 1. Press the MENU button to display OSD menu. -
Page 27: Other Related Osd Menus
Projector User’s Manual Other Related OSD Menus Following are the descriptions on the on-screen display menus with video input sources and without input source attached to your projector. Video Input Signal If the input signal comes from S-video, composite video or component video (YCbCr), you may see VIDEO menu interface. -
Page 28: Other Osd Menus
Projector User’s Manual The following table provides detail of the available sub-menu choices: Sub-Menu Option Description Source Video format selection. Auto Automatically scans video format. PAL 4.43 Sets video format as PAL 4.43. NTSC 4.43 Sets video format as NTSC 4.43. PAL N Sets video format as PAL N. -
Page 29: No Input Signal
Projector User’s Manual No Input Signal If there is no input signal attached with your projector, you press the MENU button (on either the Projector Control Panel or the Remote Controller), one of the following on- screen display menus will appear on the screen. Input Menu (refer to page 19) Option Menu... -
Page 30: Maintenance
Projector User’s Manual MAINTENANCE The projector needs little maintenance. You should keep the lens clean as dust, dirt or spots will project on the screen and diminish image quality. You will also need to clean the air filter located at the bottom of the projector periodically. It is important to keep the air filter clean because a clogged air filter prevents proper ventilation which is necessary to cool the projector and prevent it from overheating. -
Page 31: Cleaning The Air Filter
Projector User’s Manual Cleaning the Air Filter The air filter, which is located at the bottom of the projector, should be cleaned after every 100 hours of use. If it is not cleaned periodically, it can become clogged with dust and prevent the projector from being ventilated properly. This can cause overheating and damage the projector. -
Page 32: Replacing The Lamp
Projector User’s Manual Replacing the Lamp The projector lamp used for the light source has a certain life. It is time to replace them lamp when: When lamp dims, the projected image gets darker or starts to deteriorate. The projector lamp LED indicator turns to red (See page 15). Caution: The lamp becomes high temperature after turning off the projector with the power button. -
Page 33: Technical Specifications
Projector User’s Manual TECHNICAL SPECIFICATIONS Projection System 3 panel 0.7” LCD projector Native Resolution 800x600 (480,000 dotx3) Image Brightness 1400 ANSI Lumens (TYP) Uniformity Lens Manual Zoom (1.3X) Focal Length 21.5~28mm Contrast Ratio 500:1(B/W) Aspect Ratio 4:3, supports 16:9 Screen Size 30’’~300’’... -
Page 34: Preset Signals
Projector User’s Manual APPENDIX A Preset Signals Preset signal fH (kHz) fV (Hz) Sync Size Video 60 Hz 15.734 59.940 Video 50 Hz 15.625 50.000 Component 60 Hz 15.734 59.940 S on G/Y or Composite Sync Component 50 Hz 15.625 50.000 S on G/Y or Composite Sync... -
Page 35: Hdtv Preset Signals
Projector User’s Manual HDTV Preset Signals Preset Signals Horizontal Vertical Active fH(kHz) fV(Hz) Active Pixel Pixel 480p 31.469 59.940 720p 1280 45.000 60.000 1080i 1920 1080 33.716 29.970 576p 31.250 50.000 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ EN-35... - Page 36 Projector User’s Manual Monitor OUT cable (for data) Display Set Monitor OUT Cable Monitor IN Connecting the Computer (data) Audio Cable Projector Computer Computer Cable VGA OUT ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ EN-36...
- Page 37 Projector User’s Manual Connecting the HDTV (data) AV Composite Cable Audio OUT Audio IN Digital Tunner Green,Blue,Red HDTV IN HDTV (HDTV to D-SUB Cable) Connecting to a Video Source (S-Video, Component, Composite) Video out VCR AV Composite Cable S-Video Cable DVD Player YPbPr (HDTV to D-SUB Cable) Y Cb Cr(Component Video Cable)
- Page 38 (i) proof of date of purchase; (ii) the dealer’s name; and (iii) the model and serial number of the Product. When sending your unit in for repair, please ship your unit in its original packing material or a Boxlight approved ATA Shipping Case, or have a professional packaging company pack the unit.
- Page 39 THERE ARE NO WARRANTIES THAT EXTEND BEYOND THE FACE HEREOF AND THE FOREGOING WARRANTY SHALL NOT BE EXTENDED, ALTERED OR VARIED EXCEPT BY WRITTEN INSTRUMENT SIGNED BY BOXLIGHT. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY MAY LAST, SO SUCH LIMITATIONS MAY NOT APPLY TO YOU.