Page 2
Product notice This user guide describes features that are common to most models. Some features may not be available on your computer. To obtain the latest information in the Notebook PC User Guide, go to the HP Web site at http://www.hp.com/support.
Page 3
Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.
Identifying wireless and network status icons ... 14 Using the wireless controls ... 14 Using the wireless action key ... 14 Using HP Wireless Assistant ... 15 Using operating system controls ... 15 Using a WLAN ... 15 Setting up a WLAN ... 16 Protecting your WLAN ...
Page 6
Current network security codes are unavailable ... 20 WLAN connection is very weak ... 21 Cannot connect to the wireless router ... 21 Connecting to a local area network ... 22 3 Pointing devices and keyboard ... 23 Using the TouchPad ... 23 Turning the TouchPad on and off ...
Page 7
Displaying the remaining battery charge ... 63 LightScribe DVD+R discs ... 41 Blu-ray Disc ... 41 Obtaining the latest HP device drivers ... 57 Obtaining the latest Windows device drivers ... 57 Initiating and exiting Sleep ... 58 Initiating and exiting Hibernation ... 59 Viewing the current power plan ...
Page 8
Finding battery information in Help and Support ... 63 Using Battery Check ... 64 Inserting or removing the battery ... 64 Charging a battery ... 66 Maximizing battery discharge time ... 66 Managing low battery levels ... 66 Calibrating a battery ... 67 Conserving battery power ...
Page 9
8 Memory modules ... 82 9 Security ... 86 Protecting the computer ... 86 Using passwords ... 86 Setting passwords in Windows ... 87 Setting passwords in Setup Utility ... 87 Using antivirus software ... 89 Using firewall software ... 90 Installing critical updates ...
Page 10
Performing a recovery ... 103 Recovering from the recovery discs ... 104 Recovering from the dedicated recovery partition (select models only) ... 104 Index ... 105 Create a system restore point ... 103 Restore to a previous date and time ... 103...
Features Identifying hardware To see a list of hardware installed in the computer, follow these steps: Select Start > Control Panel > System and Security. Then, in the System area, check Device ▲ Manager. You can also add hardware or modify device configurations using Device Manager. NOTE: Windows®...
Page 12
Component TouchPad off indicator TouchPad zone Left TouchPad button Right TouchPad button There is an unmarked scroll zone inside the right edge of the TouchPad. To scroll up and down using the TouchPad vertical scroll zone, slide your finger up or down inside the right edge of the TouchPad. For more information about TouchPad features, refer to “Using the TouchPad”...
Lights Component TouchPad light Caps lock light Power light Wireless light Description ● On: The TouchPad is disabled. ● Off: The TouchPad is enabled. On: Caps lock is on. ● On: The computer is on. ● Blinking: The computer is in the Sleep state. ●...
Button and speakers Component Speakers (2) Power button Chapter 1 Features Description Produce sound. ● When the computer is off, press the button to turn on the computer. ● When the computer is on, press the button briefly to initiate Sleep.
Keys Component Windows logo key Windows applications key Navigation keys Action keys Description Displays system information when pressed in combination with key. Displays system information when pressed in combination with key. Displays the Windows Start menu. Displays a shortcut menu for items beneath the pointer. Navigate using the Up, Down, Left and Right arrow keys.
Display Component Internal microphone Integrated webcam (select models only) Integrated webcam light (select models only) Chapter 1 Features Description Records sound. Records audio and video and captures still photographs. On: The integrated webcam is in use.
Right-side components Component Optical drive Optical drive light USB port RJ-11 (modem) jack (select models only) AC adapter/power/battery light Power connector Security cable slot Description Reads and writes to optical discs. Blinking: The optical drive is being accessed. Connects an optional USB device. Connects a modem cable.
Left-side components Component External monitor port Vent HDMI port (select models only) RJ-45 (network) jack USB ports (2) Audio-in (microphone) jack Audio-out (headphone) jack Digital Media Slot (select models only) Drive light Chapter 1 Features Description Connects an external VGA monitor or projector. Enables airflow to cool internal components.
Bottom components Component Battery bay Battery release latch Vents (4) Memory module compartment Hard drive bay Description Holds the battery. Releases the battery from the battery bay. Enable airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating.
Wireless antennas At least 2 antennas send and receive signals from one or more wireless devices. These antennas are not visible from the outside of the computer. NOTE: For optimal transmission, keep the areas immediately around the antennas free from obstructions.
Additional hardware components Component Power cord* AC adapter Battery *Power cords vary in appearance by country or region. WARNING! Connecting the internal analog modem to a digital line can permanently damage the modem. Immediately disconnect the modem cable if you accidentally connect it to a digital line. NOTE: Telephone jacks vary by country or region.
Labels The labels affixed to the computer provide information you may need when you troubleshoot system problems or travel internationally with the computer: ● Serial number label—Provides important information that you may need when contacting technical support. The serial number label is affixed inside the battery bay. Component Product name Serial number...
Wireless, local area network, and modem Using wireless devices Wireless technology transfers data across radio waves instead of wires. Your computer may be equipped with one or more of the following wireless devices: ● Wireless local area network (WLAN) device—Connects the computer to wireless local area networks (commonly referred to as Wi-Fi networks, wireless LANs, or WLANs) in corporate offices, your home, and public places such as airports, restaurants, coffee shops, hotels, and universities.
Wireless (connected) Identifies the location of the wireless light and the wireless action key (f12) on the computer. Also identifies the HP Wireless Assistant software on the computer and indicates that one or more of the wireless devices are on.
Using HP Wireless Assistant A wireless device can be turned on or off using HP Wireless Assistant. If a wireless device is disabled in Setup Utility, it must be reenabled in Setup Utility before it can be turned on or off using Wireless Assistant.
NOTE: The terms wireless router and wireless access point are often used interchangeably. ● A large-scale WLAN, such as a corporate or public WLAN, typically uses wireless access points that can accommodate a large number of computers and accessories and can separate critical network functions.
Protecting your WLAN Because the WLAN standard was designed with only limited security capabilities—basically to foil casual eavesdropping rather than more powerful forms of attack—it is essential to understand that WLANs are vulnerable to well-known and well-documented security weaknesses. WLANs in public areas, or “hotspots,” like coffee shops and airports may not provide any security. New technologies are being developed by wireless manufacturers and hotspot service providers that make the public environment more secure and anonymous.
Connecting to a WLAN To connect to the WLAN, follow these steps: Be sure that the WLAN device is on. If it is on, the wireless light is white. If the wireless light is amber, press the wireless action key (f12). Click the network icon in the notification area, at the far right of the taskbar.
Bluetooth and Internet Connection Sharing (ICS) HP does not recommend setting up one computer with Bluetooth as a host and using it as a gateway through which other computers may connect to the Internet. When two or more computers are connected using Bluetooth, and Internet Connection Sharing (ICS) is enabled on one of the computers, the other computers may not be able to connect to the Internet using the Bluetooth network.
A Windows “Device not Found” error message may also be displayed. The driver must be reinstalled. Get the latest version of the WLAN device software and drivers for your computer from the HP Web site at http://www.hp.com. If the WLAN device you are using was purchased separately, consult the manufacturer's Web site for the latest software.
SSID and network key are alphanumeric codes that you enter into your computer to identify your computer to the network. ● For a network connected to your personal wireless router, review the router user guide for instructions on setting up the same codes on both the router and the WLAN device. ●...
If the computer still cannot make a connection to a WLAN, restart the wireless router. For details, refer to the router manufacturer's instructions. Connecting to a local area network Connecting to a local area network (LAN) requires an 8-pin, RJ-45 network cable (purchased separately).
Pointing devices and keyboard Using the TouchPad The following illustration and table describe the computer TouchPad. Component TouchPad off indicator TouchPad zone Left TouchPad button Right TouchPad button To move the pointer, slide your finger across the TouchPad surface in the direction you want the pointer to go.
NOTE: If you are using the TouchPad to move the pointer, you must lift your finger off the TouchPad before moving it to the scroll zone. Simply sliding your finger from the TouchPad to the scroll zone will not activate the scrolling function. Turning the TouchPad on and off The TouchPad is turned on at the factory.
Pinching Pinching allows you to zoom in or out on items such as PDFs, images, and photos. To pinch: ● Zoom in by holding two fingers together on the TouchPad, and then pull the fingers apart to increase an object's size. ●...
Setting pointing device preferences Use Mouse Properties in Windows® to customize settings for pointing devices, such as button configuration, click speed, and pointer options. To access Mouse Properties, select Start > Devices and Printers. Then right-click the device representing your computer, and select Mouse settings. Connecting an external mouse You can connect an external USB mouse to the computer using one of the USB ports on the computer.
prt sc Using the hotkey A hotkey is a combination of the Pressing fn+esc displays information about system hardware components and the system BIOS version number. Opens Help and Support, which provides information about your Windows operating system and computer, answers to questions and tutorials, and updates to your computer.
To use a hotkey command on the computer keyboard, follow either of these steps: ● Briefly press the – or – ● Press and hold down the Cleaning the TouchPad and keyboard Dirt and grease on the TouchPad can cause the pointer to jump around on the screen. To avoid this, clean the TouchPad with a damp cloth, and wash your hands frequently when using the computer.
Multimedia Multimedia features Your computer includes multimedia features that allow you to listen to music, watch movies, and view pictures. Your computer may include the following multimedia components: ● Optical drive for playing audio and video discs ● Integrated speakers for listening to music ●...
Page 41
Component Internal microphone Webcam (select models only) Webcam light (select models only) Volume down action key (f9) Volume up action key (f10) Volume mute action key (f11) Speakers (2) Audio-out (headphone) jack Audio-in (microphone) jack Description Records sound. Records audio and video and captures still photographs. Turns on when video software accesses the webcam.
Adjusting the volume You can adjust the volume using the following controls: ● Computer volume action keys: ◦ To decrease volume incrementally, press the volume down action key (f9) (1). ◦ To increase volume incrementally, press the volume up action key (f10) (2). ◦...
Under Behaviors in the Volume section, select Show icon and notifications. Click OK. ● Program volume control: Volume can also be adjusted within some programs. Using the media activity action keys The media activity action keys control the play of an audio CD or a DVD or BD (Blu-ray Disc) that is inserted into an optical drive.
Multimedia software Your computer includes preinstalled multimedia software that allows you to play music, watch movies, and view pictures. The following sections provide details about CyberLink PowerDVD and other preinstalled multimedia software. Using CyberLink PowerDVD software CyberLink PowerDVD turns your computer into a mobile entertainment center. With CyberLink PowerDVD, you can enjoy music and DVD movies.
Connecting external audio devices WARNING! To reduce the risk of personal injury, adjust the volume before putting on headphones, earbuds, or a headset. For additional safety information, refer to the Regulatory, Safety and Environmental Notices. To connect external devices such as external speakers, headphone, or a microphone, refer to the information provided with the device.
Connecting an external monitor or projector The external monitor port connects an external display device such as an external monitor or a projector to the computer. To connect a display device, connect the device cable to the external monitor port. ▲...
Connecting an HDMI device (select models only) Select models include an HDMI (High Definition Multimedia Interface) port. The HDMI port connects the computer to an optional video or audio device, such as a high-definition television, or any compatible digital or audio component. The computer can support one HDMI device connected to the HDMI port, while simultaneously supporting an image on the computer display or any other supported external display.
Configuring audio for HDMI (select models only) To configure HDMI audio, first connect an audio or video device, such as a high-definition TV, to the HDMI port on your computer. Then configure the default audio playback device as follows: Right-click the Speakers icon in the notification area, at the far right of the taskbar, and then click Playback devices.
Using optical discs An optical drive plays optical discs. Your optical drive can read standard CD and DVD discs, and if it is a Blu-ray Disc ROM Drive, it can also read Blu-ray Discs (BDs). These discs store information, such as music, photos, and movies. DVDs have a larger storage capacity than CDs, and BDs have the largest capacity of all.
Selecting the right disc An optical drive supports optical discs (CDs, DVDs, and BDs). CDs, used to store digital data, are also used for commercial audio recordings and are convenient for your personal storage needs. DVDs and BDs are used primarily for movies, software, and data backup purposes. DVDs and BDs are the same form factor as CDs, but DVDs have 6 to 7 times the storage capacity of CDs, and BDs have 5 to 6 times the storage capacity of DVDs.
LightScribe DVD+R discs Use LightScribe DVD+R discs for sharing and storing data, home videos, and photos. These discs are read-compatible with most DVD-ROM drives and DVD video players. With a LightScribe-enabled drive and LightScribe software, you can write data to the disc and then add a designer label to the outside of the disc.
Page 52
Gently press the disc (3) down onto the tray spindle until the disc snaps into place. Close the disc tray. If you have not yet configured AutoPlay, as described in the following section, an AutoPlay dialog box opens. It prompts you to select how you want to use the media content. NOTE: For best results, be sure that your AC adapter is plugged into an external power source while playing a BD.
Configuring AutoPlay Select Start > Default Programs > Change AutoPlay settings. Confirm that the Use AutoPlay for all media and devices check box at the upper left of the computer screen is selected. Click Choose a default, and then select one of the available options for each media type listed. Click Save.
CAUTION: To prevent loss of information or damage to a disc, observe the following guidelines: Before writing to a disc, connect the computer to a reliable external power source. Do not write to a disc while the computer is running on battery power. Before writing to a disc, close all open programs except the disc software you are using.
Creating (burning) a CD or DVD If your computer includes a CD-RW, DVD-RW, or DVD±RW optical drive, you can use software such as Windows Media Player or CyberLink Power2Go to burn data and audio files, including MP3 and WAV music files. To burn video files to a CD or DVD, use MyDVD. Observe the following guidelines when burning a CD or DVD: ●...
Removing an optical disc (CD, DVD, or BD) Press the release button (1) on the drive bezel to release the disc tray, and then gently pull out the tray (2) until it stops. Remove the disc (3) from the tray by gently pressing down on the spindle while lifting the outer edges of the disc.
Removing the optical drive The optical drive can be removed to reduce the weight of the computer: Save your work. Shut down the computer and close the display. If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the power button.
Page 58
Remove the security screw from the optical drive. NOTE: A screw driver may be necessary to loosen the bracket holding the optical drive after the security screw is removed. Remove the optical drive from the optical drive bay. Chapter 4 Multimedia...
Replace the security screw. Align the tabs (1) on the hard drive cover with the notches on the computer, close the hard drive cover (2), and tighten the hard drive screws (3). Replace the battery. Turn the computer right-side up, and then reconnect external power and external devices. Turn on the computer.
NOTE: The first time you access the YouCam software, you may experience a brief delay as the software loads. Using YouCam as your webcam software enables you to experiment with the following features: ● Video—Record and play back webcam video. You can also e-mail or upload video to YouTube, using the icon on the software interface.
Adjusting webcam properties You can adjust webcam properties using the Properties dialog box, which is accessible from various programs that use the webcam, usually from a configuration, settings, or properties menu: ● Brightness—Controls the amount of light that is incorporated into the image. A higher brightness setting creates a brighter image;...
Page 62
Remove the disc (3) from the tray by gently pressing down on the spindle while lifting the outer edges of the disc. Hold the disc by the edges and avoid touching the flat surfaces. NOTE: If the tray is not fully accessible, tilt the disc carefully as you remove it. Close the disc tray and place the disc in a protective case.
The computer does not detect the optical drive If Windows does not detect an installed device, the device driver software may be missing or corrupted. If you suspect that the optical drive is not being detected, verify that the optical drive is listed in the Device Manager utility.
A disc does not play ● Save your work and close all open programs before playing a CD or a DVD. ● Log off the Internet before playing a CD or a DVD. ● Be sure that you insert the disc properly. ●...
A movie stops, skips, or plays erratically ● Clean the disc. ● Conserve system resources by trying the following suggestions: ◦ Log off the Internet. ◦ Change the color properties of the desktop: 1. Right-click on a blank area of the computer desktop, and select Screen resolution. 2.
A DVD playing in Windows Media Player produces no sound or display Use CyberLink PowerDVD to play a DVD. CyberLink PowerDVD is installed on the computer and is also available from the HP Web site at http://www.hp.com. A device driver must be reinstalled Remove any discs from the optical drive.
Obtaining the latest HP device drivers Open your Web browser, go to http://www.hp.com/support, and select your country or region. Click the option for software and driver downloads, type your computer model number in the search box, and then press enter.
Power management Setting power options Using power-saving states The computer has two power-saving states enabled at the factory: Sleep and Hibernation. When Sleep is initiated, the power lights blink and the screen clears. Your work is saved to memory, letting you exit the Sleep state faster than exiting Hibernation. If the computer is in the Sleep state for an extended period or if the battery reaches a critical battery level while in the Sleep state, the computer initiates Hibernation.
When the computer exits Sleep, the power lights turn on and your work returns to the screen where you stopped working. NOTE: If you have set a password to be required when the computer exits Sleep, you must enter your Windows password before your work will return to the screen.
The following power plans are available: ● HP recommended ● High performance ● Power saver You can change the settings of these power plans through Power Options. Viewing the current power plan Click the battery meter icon in the notification area, at the far right of the taskbar.
To reduce potential safety issues, use only the AC adapter provided with the computer, a replacement AC adapter provided by HP, or a compatible AC adapter purchased from HP. Connect the computer to external AC power under any of the following conditions: WARNING! Do not charge the battery while you are onboard aircraft.
Connecting the AC adapter WARNING! To reduce the risk of electric shock or damage to the equipment: Plug the power cord into an AC outlet that is easily accessible at all times. Disconnect power from the computer by unplugging the power cord from the AC outlet (not by unplugging the power cord from the computer).
WARNING! To reduce potential safety issues, use only the battery provided with the computer, a replacement battery provided by HP, or a compatible battery purchased from HP. Battery life varies, depending on power management settings, programs running on the computer, display brightness, external devices connected to the computer, and other factors.
Using Battery Check Help and Support provides information on the status of the battery installed in the computer. To run Battery Check: Connect the AC adapter to the computer. NOTE: The computer must be connected to external power for Battery Check to function properly. Select Start >...
Charging a battery WARNING! Do not charge the computer battery while you are onboard aircraft. The battery charges whenever the computer is plugged into external power through an AC adapter or an optional power adapter. The battery charges whether the computer is off or in use, but it charges faster when the computer is off.
Resolving a low battery level CAUTION: To reduce the risk of losing information when the computer reaches a critical battery level and has initiated Hibernation, do not restore power until the power lights turn off. Resolving a low battery level when external power is available Connect one of the following devices: ▲...
To fully charge the battery: Insert the battery into the computer. Connect the computer to an AC adapter or an optional power adapter, and then plug the adapter into external power. Leave the computer plugged into external power until the battery is fully charged. Step 2: Disable Hibernation and Sleep Click the battery meter icon in the notification area, and then click More Power options.
Step 4: Fully recharge the battery To recharge the battery: Plug the computer into external power and maintain external power until the battery is fully recharged. You can use the computer while the battery is recharging, but the battery will charge faster if the computer is off.
Battery Check notifies you to replace the battery when an internal cell is not charging properly, or when the battery storage capacity has reached a weak condition. A message refers you to the HP Web site for more information about ordering a replacement battery. If the battery is possibly covered by an HP warranty, instructions include a warranty ID.
Page 81
If the computer is unresponsive and you are unable to use the preceding shut down procedures, try the following emergency procedures in the sequence provided: ● Press ctrl+alt+delete, and then click the Power button. ● Press and hold the power button for at least 5 seconds. ●...
Drives Handling drives Drives are fragile computer components that must be handled with care. Refer to the following cautions before handling drives. Additional cautions are included with the procedures to which they apply. CAUTION: To reduce the risk of damage to the computer, damage to a drive, or loss of information, observe these precautions: Before you move a computer that is connected to an external hard drive, initiate Sleep and allow the screen to clear, or properly disconnect the external hard drive.
HP recommends defragmenting your hard drive at least once a month. You may set Disk Defragmenter to run on a monthly schedule, but you can defragment your computer manually at any time.
Using Disk Cleanup Disk Cleanup searches the hard drive for unnecessary files that you can safely delete to free up disk space and help the computer to run more efficiently. To run Disk Cleanup: Select Start > All Programs > Accessories > System Tools > Disk Cleanup. Follow the on-screen instructions.
Page 85
Remove the hard drive screws (1), and then lift the hard drive slightly (2). Disconnect the hard drive cable, and then lift the hard drive away from the computer. Replacing the hard drive...
Page 86
To install a hard drive: Lower the hard drive into the hard drive bay, and then connect the hard drive cable. Snap the hard drive into place (1), and then replace the hard drive screws (2). Align the tabs (1) on the hard drive cover with the notches on the computer. Close the cover (2).
Page 87
Tighten the hard drive cover screws (3). Replace the battery. Turn the computer right-side up, and then reconnect external power and external devices. Turn on the computer. Replacing the hard drive...
External devices and external media cards Using a USB device Universal Serial Bus (USB) is a hardware interface that can be used to connect an optional external device, such as a USB keyboard, mouse, drive, printer, scanner, or hub. Devices can be connected to the system.
Removing a USB device CAUTION: To prevent loss of information or an unresponsive system, use the following procedure to safely remove a USB device. CAUTION: To prevent damage to a USB connector, do not pull on the cable to remove the USB device. To remove a USB device: Click the Safely Remove Hardware and Eject Media icon in the notification area, at the far right of the taskbar.
Page 90
Insert the card into the Digital Media Slot, and then push in on the card until it is firmly seated. You will hear a sound when the device has been detected, and a menu of options may be displayed. Chapter 7 External devices and external media cards...
Removing a digital card CAUTION: To prevent loss of data or an unresponsive system, use the following procedure to safely remove the digital card. Save your information and close all programs associated with the digital card. NOTE: To stop a data transfer, click Cancel in the operating system Copying window. To remove a digital card: Click the Safely Remove Hardware and Eject Media icon in the notification area, at the far right of the taskbar.
Memory modules The computer has one memory module compartment, which is located on the bottom of the computer. WARNING! To reduce the risk of electric shock and damage to the equipment, unplug the power cord and remove all batteries before installing a memory module. CAUTION: Electrostatic discharge (ESD) can damage electronic components.
Page 93
Loosen the memory module compartment screws (1). Lift the memory module compartment cover (2) away from the computer. If you are replacing a memory module, remove the existing memory module: Pull away the retention clips (1) on each side of the memory module. The memory module tilts up.
Page 94
CAUTION: To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module, and do not bend the memory module. Align the notched edge (1) of the memory module with the tab in the memory module slot. With the memory module at a 45-degree angle from the surface of the memory module compartment, press the module (2) into the memory module slot until it is seated.
Page 95
Turn the computer right-side up, and then reconnect external power and external devices. Turn on the computer.
Security Protecting the computer Standard security features provided by the Windows operating system and the non-Windows Setup Utility can protect your personal settings and data from a variety of risks. Follow the procedures in this chapter to use the following features: ●...
You can use the same password for a Setup Utility feature and for a Windows security feature. You can also use the same password for more than one Setup Utility feature. Use the following guidelines when setting a password in Setup Utility: ●...
Administrator password Your administrator password protects the configuration settings and system identification information in Setup Utility. After this password is set, you must enter it each time you access Setup Utility. Your administrator password is not interchangeable with an administrator password set in Windows, nor is it displayed as it is set, entered, changed, or deleted.
To access Norton Internet Security, or to get more information about it, click Start > All Programs > Norton Internet Security. NOTE: HP recommends that you always update the antivirus software to help protect your computer. NOTE: For more information about computer viruses, type viruses in the Search box in Help and Support.
Using firewall software When you use the computer for e-mail, network, or Internet access, unauthorized persons may be able to gain access to the computer, your personal files, and information about you. Use the firewall software preinstalled on the computer to protect your privacy. Firewall features include logging and reporting of network activity, and automatic monitoring of all incoming and outgoing traffic.
Installing critical updates CAUTION: Microsoft sends alerts regarding critical updates. To protect the computer from security breaches and computer viruses, install all critical updates from Microsoft as soon as you receive an alert. Updates to the operating system and other software may have become available after the computer was shipped.
10 Setup Utility (BIOS) Starting Setup Utility Setup Utility is a ROM-based information and customization utility that can be used even when your Windows® operating system is not working. The utility reports information about the computer and provides settings for startup, security, and other preferences.
Your change goes into effect immediately. Navigating and selecting in Setup Utility Because Setup Utility is not Windows based, it does not support the TouchPad. Navigation and selection are by keystroke. ● To choose a menu or a menu item, use the arrow keys. ●...
Setup Utility default settings go into effect when the computer restarts. NOTE: Your password, security, and language settings are not changed when you restore the factory default settings. Exiting Setup Utility You can exit Setup Utility with or without saving changes. ●...
System Configuration menu Select Language Support Button Sound (select models only) Virtualization Technology (select models only) Processor C6 State (select models only) LAN Power Saving (select models only) Card Reader/1394 Power Saving (select models only) Fan Always On Action Keys Mode Boot Options Diagnostics menu Select...
11 Software updates Updated versions of the software provided with your computer may be available on the HP Web site. Most software and BIOS updates on the HP Web site are packaged in compressed files called SoftPaqs. Some download packages contain a file named Readme.txt, which contains information regarding installing and troubleshooting the file.
Do not insert, remove, connect, or disconnect any device, cable, or cord. To download a BIOS update: Access the page on the HP Web site that provides software for your computer: Select Start > Help and Support > Maintain. Follow the instructions on the screen to identify your computer and access the BIOS update you want to download.
To download and install software other than a BIOS update, follow these steps: To use the HP Web site: Open your Web browser, go to http://www.hp.com/support, and select your country or region. Click the option for software and driver downloads, type your computer model number in the Search box, and then press enter.
HP Recovery drive is listed in the window. Creating recovery discs HP recommends that you create recovery discs to be sure that you can restore your system to its original factory state if you experience serious system failure or instability. Create these discs after setting up the computer for the first time.
NOTE: The external hard drive must be connected to a USB port on the computer, not to a USB port on an external device such as a hub. ● You will need high-quality DVD-R, DVD+R, BD-R (writable Blu-ray), or CD-R discs. All these discs are purchased separately.
Page 111
Open a word-processing document, and then select Edit > Paste. Save the document. ● You can back up your information to an optional external hard drive, a network drive, or discs. ● When backing up to discs, use any of the following types of discs (purchased separately): CD-R, CD-RW, DVD+R, DVD-R, or DVD±RW.
Using Windows Backup and Restore To create a backup using Windows Backup and Restore, follow these steps: NOTE: Be sure that the computer is connected to AC power before you start the backup process. NOTE: The backup process may take over an hour, depending on file size and the speed of the computer.
NOTE: You can recover only files that you have previously backed up. HP recommends that you use HP Recovery Manager to create a set of recovery discs (entire drive backup) as soon as you set up your computer. Recovery Manager software allows you to repair or restore the system if you experience system failure or instability.
not have a recovery partition. If that is the case, recovery discs have been included with your computer. Use these discs to recover your operating system and software. NOTE: Windows has its own built-in repair features, such as System Restore. If you have not already tried these features, try them before using Recovery Manager.
Index Symbols/Numerics 1394 Power Saving 95 AC adapter connecting 62 identifying 11 action keys decrease screen brightness 27 Help and Support 27 increase screen brightness 27 media activity 33 next track 27 play, pause, resume 27 previous track 27 stop 27 switch screen image 27 volume down 27, 31, 32 volume mute 27, 31, 32...
Page 116
HP drivers 57 Windows drivers 57 Diagnostics menu 95 digital card defined 79 inserting 79 removing 81 stopping 81 Digital Media Slot light, identifying 8 Digital Media Slot, identifying 8 Disk Cleanup software 74 Disk Defragmenter software 73...
Page 118
55 disc play 54 DVD movie play 55 external display 55 HP device drivers 57 optical disc tray 51 optical drive detection 53 Windows device drivers 57 turning off the computer 70 unresponsive system 70 USB cable, connecting 78...