Toshiba MCY-MHP1006HS8-E Owner's Manual page 16

2FAN_OM_DB04307201-04_EN.book Page 15 Tuesday, December 17, 2019 6:33 PM
To stop swinging
1
Push the SWING/FIX button at the desired position
while the louver is swinging.
• Push the SWING/FIX button repeatedly to change
the louver position again.
* However, even if the button is pushed while
SWING/FIX
the louver is swinging, one of the indications
below may sometimes be displayed and may not
set the louver to the highest position.
Indications when swinging is stopped
FAN/HEAT COOL/DRY
In this case, push the SWING/FIX button again after 2
seconds.
• In COOL/DRY operation, the louver does not stop
as it directs downward. If stopping the louver as it
directs downward during swing operation, it stops
after moving to the third position from the highest
position.
Indications when swinging is stopped
FAN/HEAT COOL/DRY
operation operation
Unit select
• When two or more indoor units are controlled with one
remote controller, the louver direction can be set for
each indoor unit by selecting them individually.
• To set louver direction individually, push the
UNIT LOUVER
button (left side of the button) to display an indoor unit
number in the control group. Then set the louver
direction of the displayed indoor unit.
• When no indoor unit number is displayed, all indoor
units in the control group can be controlled
simultaneously.
• Each time you push the UNIT LOUVER (left side of the button),
the indication changes as follows:
No Unit No. Unit No.
display 1-1 1-2
Unit No. Unit No.
1-4 1-3
EN-29
– 15 –
 4-way cassette type 2H series
only
To set the louvers individually
1
Push the UNIT LOUVER button (left side of the button)
during running to select a unit.
The unit number changes each time you push the
button.
Unit No. Unit No. Unit No.
1-1 1-2 1-3
No Unit No.
display 1-4
• When no unit number is displayed, all units are
selected.
2
Push the UNIT LOUVER button (right side of the button)
to select a louver.
Each time you push the button, the indicator on the
left of the remote controller changes as follows:
No
display
* When no louver number is displayed, all 4 louvers
are selected.
Louver No.
Electrical control box
Refrigerant
pipe
Drain pipe
3
Push the SWING/FIX button to confirm the direction of
the selected louver.
Each time you push the button, the indication
changes as follows:
(1) (2) (3) (4)
(7) (6) (5)
* When cooling or drying, (4) and (5) are not displayed.
Setting the swing pattern
1
Push and hold the SWING/FIX button for at least 4
seconds while the operation is stopped.
blinks.
2
Push the button (left side of the button)
UNIT LOUVER
to select a unit.
The unit number changes each time you push the
button.
Unit No. Unit No. Unit No.
1-1 1-2 1-3
No Unit No.
display 1-4
The fan of the selected unit runs, and the louver swings.
3
Push the TIME buttons to select a swing
type.
Swing code
Swing code Movement pattern
Standard swing
0001
(factory default)
0002 Dual swing
0003 Cyclic swing
REQUIREMENT
Do not set "0000".
(The louver may be damaged.)
Owner's Manual
4
Push the button.
5
Push the button to finish the setting.
Standard swing
All four louvers swing simultaneously at the same
angle.
Swing
Dual swing (Recommended for heating)
• Adjoining louvers alternately point horizontally and
downward to heat the room evenly.
• Air blown downward reaches the floor, and air blown
horizontally is spread to circulate heat.
Horizontal
Horizontal
Downward
Downward
Horizontal
Horizontal
Downward
Downward
EN-30