Related Manuals for Hardy Barth CPMICRO1
Summary of Contents for Hardy Barth CPMICRO1
- Page 1 Charging Station cPµ1 Instruction Manual Instruction Manual cPμ1 charging station Version: 1.3.3...
-
Page 2: Contact Details
Contact Details eCHARGE Hardy Barth GmbH Manufacturer Leinbergstraße 14 92262 Birgland-Schwend Germany Phone: +49 (0) 9666 188 1350 Fax: +49 (0) 9666 188 1351 Web: www.echarge.de E-Mail: support@echarge.de Instruction Manual cPμ1 charging station Version: 1.3.3... -
Page 3: Table Of Contents
Contents Contact Details.......................2 Important Information....................4 Safety notices in this manual......................4 Safety notices on this device......................5 General safety notices........................6 Operating instructions/Maintenance....................8 Dimensional drawings and measurements..............10 Introduction.........................11 Product description........................12 Identifying your product variant....................12 Scope of delivery..........................13 Available accessories........................13 Preparing the installation....................14 Requirements for mounting site....................14 Installation and taking into operation.................15 Mechanical installation on wall.....................16 Electrical installation of charging station..................17... -
Page 4: Important Information
Important Information Safety notices in this manual This instruction manual contains important information for installation and putting into operation of all charging stations of type cPµ1. Please make sure to read and follow the provided safety notices in any circumstances. In particular, the warnings and safety measures clearly marked in this manual must be followed. -
Page 5: Safety Notices On This Device
Safety notices on this device Further safety notices and operating instructions can be found on and also inside the device. These symbols carry the following meanings: Attention! Only qualified staff which are familiar with this manual (this document) are allowed to open the cpµ1. -
Page 6: General Safety Notices
General safety notices Before you start operating your cPµ1 charging station, please make sure you have carefully read the manual, heeded and followed all instructions and warnings. The installation, repair and maintenance of the cPµ1 as well as taking into operation must be carried out by qualified staff. - Page 7 A service case occurs, when... • …the housing has been damaged mechanically, • …the housing cover has been removed or cannot be closed or locked anymore • …the necessary protection against water and/or foreign objects seems not to be provided anymore •...
-
Page 8: Operating Instructions/Maintenance
Operating instructions/Maintenance Please note the following instructions regarding usage and maintenance of your device: • This device MUST ALWAYS be connected to the protective conductor of the power supply. • Please ensure that the rated nominal voltage and rated nominal current of the device correspond with the requirements of your local power supply system and that the nominal capacity is not exceeded during charging. - Page 9 • Regularly examine the charging cable and/or charging sockets of your Wallbox as well as additional accessories to find possible damage spots and/or damages in general. If damages are found on the additional charging cable, please replace them immediately. No further charging is allowed in this case. DANGER! If you find damage on the housing, charging sockets or corresponding charging cables after installation, take the Wallbox out of order immediately and...
-
Page 10: Dimensional Drawings And Measurements
Dimensional drawings and measurements The cPµ1 charging station is delivered after being completely assembled and tested. Below, all measurements and assembly points are detailed in the dimensional drawings. Charging station Front view and side view of the cPµ1-series (all specifications are in mm) Instruction Manual cPμ1 charging station... -
Page 11: Introduction
Introduction Thank you for choosing the cPµ1 charging station by e C H A R G E By choosing this product, you are investing in an innovative and sustainable solution for the public and industrial section. The charging stations of the cPµ-series are delivered pre-configured and can be installed at a prepared mounting site with minimal technical and minimal time effort. -
Page 12: Product Description
Product description Your cPµ1 charging station permits safe and comfortable charging of electric vehicles according to Norm IEC 61851-1, Mode 3. Depending on the respective variant your cPµ1 is laid out for charging as fast as possible due to its circuit design and its diameter of cables and pins. The cPµ1 also offers a fixed charging cable according to IEC 62196-2 of either Type 1 or Type 2, depending on your variant. -
Page 13: Scope Of Delivery
Scope of delivery Your cPµ1 Wallbox is delivered with various components which are essential for the installation and proper operation. Please check immediately whether your package contains the following basic components: Components Quantity Description cPμ1 charging station 1 Charging station consisting of plastic housing with a lockable cover Instruction for assembly 1 Contains... -
Page 14: Preparing The Installation
Preparing the installation Several requirements regarding the mounting site and connection technology must be met for the installation in order to guarantee a safe operation. Requirements for mounting site The cPμ1 charging station was developed for indoor as well as outdoor areas. As user, please note the following requirements for the mounting site and installation to ensure safe charging later on. -
Page 15: Installation And Taking Into Operation
Installation and taking into operation The installation has to be carried out principally by professional staff. Approval has to be given by a qualified electric company before the charging station can be taken into operation for the first time. The cPµ1 charging station is an electrotechnical device and therefore has to follow certain demands concerning the installation indoors and outdoors: Even though the housing of the cPµ1 fullfills the standards given by IP44, please note, especially for outdoors, various environmental conditions:... -
Page 16: Mechanical Installation On Wall
Mechanical installation on wall At least two persons are required to perform the following instructions. Additionally these components will be required: • An electric drilling machine or a cordless screwdriver (not included in scope of delivery) • A twist drill Ø 6 mm for the respective mounting surface (not included in scope of delivery) •... -
Page 17: Electrical Installation Of Charging Station
Electrical installation of charging station DANGER! Danger to life due to electric shock! Before working with the cPµ1 charging station: Disconnect the electrical power supply and make sure that it stays disconnected non-stop through the whole installing process. After completion of the mechanical installation the charging station will be connected to the power line. - Page 18 Description Colour of core Label Live conductor Phase 1 BROWN L1 (brown leakage) Live conductor Phase 2 BLACK L2 (black leakage) Live conductor Phase 3 GREY L3 (grey leakage) Neutral BLUE N (blue leakage) Protective conductor GREEN-YELLOW GREEN-YELLOW LEAKAGE DANGER! The previously named colour codes are NOT obligatory on an international level: If the cores are colour-coded differently please contact a qualified electrical company and have them examine the lead and if required, replace...
-
Page 19: Taking Into Operation And Charging Process
Taking into operation and charging process After the mechanical and the electrical installation, your charging station is immediately ready. The cPµ1 possesses a Type 1 or Type 2 charging cable complying with IEC 62196-2 for charging (depends on variant). The Type-2 charging cable of the cPμ1 has three live conducting... -
Page 20: Safety Notices For Operation
Safety notices for operation Please note the following safety notices before you charge with your cPµ1: • Make sure that the cPµ1 has been installed according to the requirements of this document. Mind especially that the charging device is freely accessible and is not exposed to rain or direct solar radiation. -
Page 21: Charging Process
Charging process The cPµ1 is designed to charge your vehicles as fast as possible according to IEC 61851-1 Mode 3. The effective charging time depends on the battery of your vehicle as well as on the current residual energy. Therefore, it is not possible to give a binding statement regarding the charging time. -
Page 22: Troubleshooting
Troubleshooting The cPµ1 is also designed for maximum security and reliable charging. Through internal testing routines, malfunctions are identified and immediate switch off is issued. Should there be any malfunctions during the charging process, the LED-Display will immediately indicate them. This chapter describes how to recognize the error states and operating states and which measurements are to take in order to repair the glitch. -
Page 23: Interruptions Of Operation And Solutions
Interruptions of operation and solutions The cPµ1 executes internal testing routines to guarantee proper and safe operation. In order to restore the previous operation state, first, it is essential that you determine the type of malfunction undoubtedly. DANGER! Inside the charging station life threatening voltages occur! Opening the charging station and following works on the charging station must be carried out solely by qualified staff. -
Page 24: Appendix
Appendix Technical specifications Variant cPμ1 Power line For lead up to. 5×4 mm² at maximum Rated nominal voltage 230 / 400 V Rated nominal current 16 A / 20 A, 3-phase / 1-phase Nominal frequency 50 Hz Maximum charging capacity 11 kW DC fault current detection 6 mA (built in);... -
Page 25: Standards And Guidelines
Standards and guidelines The cPμ1 fullfills the following standards and protection classes: General standards Norm Explanation 2014/30/EU EMV-guideline 2011/65/EU RoHS-guideline 2012/19/EU WEEE-guideline ElektroG Electrical and electronical laws Equipment safety standards Norm Explanation Conductive charging systems for electric vehicles IEC 61851-1 Ed 2.0:2010 part 1: general requirements Conductive charging systems for electric vehicles IEC 61851-22 (69/201/CD) - Page 26 Protection class and protection types Protection class/protection type Explanation Protection class I: all electrically conductive components of the operating device are connected low impedance with the protective conductor system of the fixed installation Protection type of housing: Protection against foreign objects < 1 mm IP 44 and protection against splashing from every direction...
-
Page 27: Guarantee Specifications And Warranty
Guarantee specifications and warranty eCHARGE provides the legally prescribed guarantee period as well as a warranty of the same duration for the country in which the product was purchased. Should the product be operated in another country, the legal provision of the country of purchase apply nevertheless: Under no circumstances are guarantees or warranty transferable.