Related Manuals for Hardy Barth cPH1
Summary of Contents for Hardy Barth cPH1
- Page 1 Charging Station cPH1 Instruction Manual Instruction Manual cPH1 charging station Version: 1.2.4...
-
Page 2: Contact Details
Contact Details Manufacturer: eCHARGE Hardy Barth GmbH Leinbergstraße 14 92262 Birgland-Schwend Phone: +49 (0) 9666 188 1350 Fax: +49 (0) 9666 188 1351 Web: www.echarge.de E-Mail: support@echarge.de Instruction Manual cPH1 charging station Version: 1.2.4... -
Page 3: Table Of Contents
Prepara on for RFID access......................20 Charging process..........................21 Par culari es................................23 Opera on status..................24 LED-Display................................24 RFID-Module (op onal).........................25 Interrup on of opera on and solu ons...........26 Appendix....................27 Technical specifica ons........................27 Standards and guidelines.......................28 Warranty / Guarantee........................30 Instruction Manual cPH1 charging station Version: 1.2.4... -
Page 4: Important Informa On
Safety notices in this manual This instruction manual contains important information for installation and putting into operation of all charging stations of type cPH1. Please make sure to read and follow the provided safety notices in any circumstances. In particular, the warnings and safety measures clearly marked in this manual must be followed. -
Page 5: Safety No Ces On This Device
These symbols carry the following meanings: General safety notices Before you start operating your cPH1 charging station please make sure you have carefully read the manual, heeded and followed all instructions and warnings. The installation, repair and maintenance of the cPH1 as well as taking into operation must be carried out by qualified staff. - Page 6 The cPH1 is sufficiently protected against spray and splash according to IP44. • The cPH1 must not be installed in an environment prone to or with danger of explosion (EX area). • Do not install the charging station in any environment prone to or with danger of flooding.
-
Page 7: Opera Ng Instruc Ons/Maintenance
(such as cleaning petrol or paint thinners for example). These can tarnish the display or damage the varnish. • The cPH1 charging station MUST NOT be cleaned with a pressure washer or similar devices which apply high pressure on the housing when cleaning. - Page 8 Wallbox out of order immediately and contact the service department of eCHARGE Hardy Barth GmbH! • The local regulations of operating electrical devices apply at any time. Instruction Manual cPH1 charging station Version: 1.2.4...
-
Page 9: Dimensional Drawings And Measurements
Dimensional drawings and measurements The cPH1 charging station is delivered after being completely assembled and tested. Below all measurements and assembly points are detailed in the dimensional drawings. Charging station Front view and side view of cPH1-series. (all specifications are in mm) -
Page 10: Introduc On
The charging stations of the cPH-series are delivered pre-configured and can be installed at a prepared mounting site with minimal technical and minimal time effort. Via the optional available eCB1 module, the cPH1 can be embedded into an already existing photovoltaic system. -
Page 11: Product Descrip On
The cPH1 offers charging via a fixed cable of either Type 1 or Type 2 and/or also via charging sockets according to IEC 62196-2 Type 2 (depends on your variant). For... -
Page 12: Iden Fying Your Product Variant
Wallbox you will find an identification plate. Open the housing cover before installation and operation in order to verify the type of variant with help of the identification plate: In particular the model description (cPH1 XTYY) and data of the power supply (voltage, power frequency, current) are relevant for identification. -
Page 13: Scope Of Delivery
Scope of delivery Your cPH1 Wallbox is delivered with various components which are essential for the installation and proper operation. Please check immediately whether your package contains the following basic components: Components Quantit Description Charging station consisting of plastic housing... -
Page 14: Preparing The Installa On
Requirements for mounting site The cPH1 charging station was developed for indoor as well as outdoor areas. As user please note the following requirements for the mounting site and installation to ensure safe charging later on. -
Page 15: Installa On And Taking Into Opera On
Your cPH1 charging station is an electrotechnical device and therefore has to follow certain demands concerning the installation indoors and outdoors: Even though the housing of the cPH1 fullfills the standards given by IP44, please note especially for outdoors various environmental conditions: •... -
Page 16: Electrical Installa On Of Charging Sta On
Electrical installation of charging station DANGER! Danger to life due to electric shock! Before working with the cPH1 charging station: Disconnect the electrical power supply and make sure that it stays disconnected non-stop through the whole installing process. After completion of the mechanical installation the charging station will be connected to the power line. - Page 17 Live conductor Phase 1 BROWN EUROFUSE NH00/000 63A Live conductor Phase 2 BLACK EUROFUSE NH00/000 63A Live conductor Phase 3 GREY EUROFUSE NH00/000 63A Neutral BLUE BLUE CONDUCTOR Protective conductor GREEN-YELLOW GREEN-YELLOW CONDUCTOR Instruction Manual cPH1 charging station Version: 1.2.4...
- Page 18 5 If there is no built-in eCB1 module and communication through the external eCB1 module is preferred instead, the RS-485 Bus cable of the external eCB1 module has to be inserted from below. The RS-485 Bus cable will be clipped in the middle of the cPH1 like so: Blue is Brown is Black is 6 Turn the circuit breakers and fault-current circuit breakers back on.
-
Page 19: Taking Into Opera On And Charging Process
After the mechanical and the electrical installation, your charging station is immediately ready. For charging there are various ways to connect your cPH1 to your EV (depends on your variant). For that an optional charging cable might be needed. For the benefit of flexibility,... -
Page 20: Safety No Ces For Opera On
• Make sure that your cPH1 is properly connected to the lead. • Make sure that the lead is protected by appropriate automatic cut outs. • Make sure the cover of the cPH1 is always securely closed during normal operation •... -
Page 21: Charging Process
Park the EV accordingly so you can reach it comfortably. During the charging process the cable MUSTN‘T be strained. 4. Open the cover of your charging socket of the cPH1 if available with your variant and plug in your Type 2 charging cable. - Page 22 This is to signify that you can remove the charging cable. Upon ending the charging process, pull the cable out of the socket of your EV and out of your cPH1. Should the EV still not be completely charged please contact the service partner of your vehicle.
-
Page 23: Par Culari Es
6 A and 32 A. The respective settings will be made through the eCB1-Module which passes the data to the vehicle. For detailed information regarding charging control please contact the contact person in your region. Instruction Manual cPH1 charging station Version: 1.2.4... -
Page 24: Opera On Status
Operation status The cPH1 charging station is also designed for maximum security and reliable charging. Through internal testing routines malfunctions are identified and immediate switch off is issued. Should there be any malfunctions during the charging process, the LED-Display and the LED lights of the RFID module will immediately indicate them. This chapter describes how to recognize the error states and operating states and which measurements are to take in order to repair the glitch. -
Page 25: Rfid-Module (Op Onal)
If your RFID card wasn’t accepted, please wait for a moment before trying again. If the charging station still doesn’t activate after that, your RFID card is either damaged or not registered in the database. Instruction Manual cPH1 charging station Version: 1.2.4... -
Page 26: Interrup On Of Opera On And Solu Ons
Interruption of operation and solutions The cPH1 executes internal testing routines to guarantee proper and safe operation. In order to restore the previous operation state, first, it is essential that you determine the type of malfunction undoubtedly. DANGER! Inside the charging station life threatening voltages occur! Opening the charging station and following works on the charging station must be carried out solely by qualified staff. -
Page 27: Appendix
Appendix Technical specifications Variant cPH1 Power line For lead of size 5 x 6 mm Rated nominal voltage 230 / 400 V Rated nominal current 16 A/ 32 A, 3-phase Nominal frequency 50 Hz Maximum charging capacity 22 kW DC fault-current detection 6 mA (built in) and circuit breaker C16 A/ C32 A (built in, depends on variant);... -
Page 28: Standards And Guidelines
Standards and guidelines The cPH1 charging station fullfills the following standards and protection classes: General standards Norm Explanation 2014/30/EU EMV-guideline 2011/65/EU RoHS-guideline 2012/19/EU WEEE-guideline ElektroG Electrical and electronical laws Equipment safety standards Norm Explanation Conductive charging systems for electric vehicles- IEC 61851-1 Ed 2.0:2010... - Page 29 Protection type of housing: Protection against foreign objects < 1mm IP 44 and protection against splashing from every direction Instruction Manual cPH1 charging station Version: 1.2.4...
-
Page 30: Warranty / Guarantee
Warranty / Guarantee Guarantee specifications and warranty eCHARGE Hardy Barth GmbH guarantees the legally prescribed warranty period of 24 month for the present product as well as a warranty of the same duration for the country in which the product was purchsaed. - Page 31 Do not, under any circumstances, make alterations or repairs to your product on your own! The company eCHARGE Hardy Barth GmbH guarantees the proper operation of the present product after delivery within the scope of the lawfully valid warranty. The warranty is limited to such damage that is attributable to normal use and to obvious material or manufacturing defects.