Advertisement
Quick Links
ECD-200BT
ELECTRONIC CABLE DRIVE
The Dakota Digital ECD-200BT is designed operate a cable-driven speedometer from a
transmission or ECM electric speed signal or from an OBDII port connection. The supplied cable
threads on to one end of the ECD-200 and the wiring harness exits on the other end. Do not use the
vehicle's original speedometer cable. The module is fully sealed and can be mounted under the dash
or in the engine compartment. The module should not be mounted under the vehicle due to the
danger of road debris causing damage. The unit is fully adjustable from the comfort of your driver's
seat. Setup can also be completed by using the Dakota Digital Accessory app available for IOS or
Android devices.
Included components
Cable drive unit
1
MAN# 650704A
Advertisement
Related Manuals for Dakota Digital ECD-200BT-1
Summary of Contents for Dakota Digital ECD-200BT-1
- Page 1 The module should not be mounted under the vehicle due to the danger of road debris causing damage. The unit is fully adjustable from the comfort of your driver’s seat. Setup can also be completed by using the Dakota Digital Accessory app available for IOS or Android devices.
- Page 2 ECD Display Panel The digital readout on the end of the ECD-200BT offers more setup options and helps to indicate what setup function is being accessed in addition to the speedometer needle feedback for certain calibration functions. While you don’t need to see the ECD unit during day-to-day operation, LED readout is useful during initial setup and for diagnostics.
- Page 3 Please see page eight for the setup steps required. Setup menu overview *To simplify the setup procedure, please download out IOS or Android app ‘Dakota Digital Accessory’* Setup is entered by holding the supplied function switch while turning the key on. Tap the switch to change selections, hold to enter a sub-menu or save an option.
- Page 4 Speedometer calibration with a speed signal wire: *To simplify the setup procedure, please download the IOS or Android app ‘Dakota Digital Accessory’* To operate the setup procedure, the orange wire needs to touch ground. The orange wire can be wired to one side of the enclosed push button switch, and the other side of the switch goes to any ground.
- Page 5 Adjust (20 MPH): - LED: “” • Needle should be pointing to 20 MPH (32 km/h). • Press and hold the switch until the needle drops to 0 MPH. Then release the switch. • The needle will move to 15 select to decrease your speed or 25 to increase your speed. •...
- Page 6 Dedicated Menu Displays The following displays in the LED panel will not have a corresponding speedometer needle movement. These are in sequence after the option. The VSS calibration adjustment is from 75% to 125% of the current calibration value, or +/- 25%. Calibration menu adjust (0 MPH): - LED: ...
- Page 7 Press and hold the switch to save until “” and exit to the main menu Bluetooth menu display: - LED: Two options are available for the Dakota Digital Accessory app: accessing the Bluetooth setup all the time or only when the ECD-200BT has manually entered setup. “” indicates the Bluetooth connectivity will be active anytime the key is on, allowing speedometer adjustments to be made while driving, while “”...
- Page 8 Speedometer calibration with an OBDII connection: *To simplify the setup procedure, please download out IOS or Android app ‘Dakota Digital Accessory’* The speedometer signal from the ECM is normally calibrated to be accurate. If there have been changes to the gearing or tire size then the reading can be adjusted from 75% to 125%.
-
Page 9: Troubleshooting
Diagnostics During normal operation, the display will show “ ” when the vehicle is not moving and “ - :” with flashing dots when the vehicle is moving. If the switch is pressed during normal operation the display will show “” if the speed input is from the brown wire and if the OBDII cable is used it will show the current bus data state. -
Page 10: Service And Repair
Dakota Digital assumes no responsibility for loss of time, vehicle use, owner inconvenience nor related expenses. Dakota Digital will cover the return standard freight once the product has been evaluated for warranty consideration; however the incoming transportation is to be covered by the owner.